SIST EN ISO 9712:2022

SLOVENSKI STANDARD
01-junij-2022
Nadomešča:
SIST EN ISO 9712:2012
Neporušitvene preiskave - Kvalificiranje in certificiranje osebja za neporušitvene
preiskave (ISO 9712:2022)
Non-destructive testing - Qualification and certification of NDT personnel (ISO
9712:2022)
Zerstörungsfreie Prüfung - Qualifizierung und Zertifizierung von Personal der
zerstörungsfreien Prüfung (ISO 9712:2022)
Essais non destructifs - Qualification et certification du personnel END (ISO 9712:2022)
Ta slovenski standard je istoveten z: EN ISO 9712:2022
ICS:
03.100.30 Vodenje ljudi Management of human
resources
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9712
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 03.100.30; 19.100 Supersedes EN ISO 9712:2012
English Version
Non-destructive testing - Qualification and certification of
NDT personnel (ISO 9712:2021)
Essais non destructifs - Qualification et certification du Zerstörungsfreie Prüfung - Qualifizierung und
personnel END (ISO 9712:2021) Zertifizierung von Personal der zerstörungsfreien
Prüfung (ISO 9712:2021)
This European Standard was approved by CEN on 16 December 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9712:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered. 4

European foreword
This document (EN ISO 9712:2022) has been prepared by Technical Committee ISO/TC 135 "Non-
destructive testing" in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 9712:2012.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 9712:2021 has been approved by CEN as EN ISO 9712:2022 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request M/071
“Mandate to CEN for standardization in the field of Pressure equipment” to provide one voluntary
means of conforming to essential requirements of Directive 2014/68/EU OF THE EUROPEAN
PARLIAMENT AND OF THE COUNCIL of 15 May 2014 on the harmonization of the laws of the Member
States relating to the making available on the market pressure equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential Requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2014/68/EU
Essential Safety Clauses/sub- clauses of this EN Remarks/Notes
Requirements (ERs) of
Directive 2014/68/EU
3.1.3 5, 6, 7, 8, 9, 10 (C2 excepted) and 11 Non-destructive testing of permanent
joints. For pressure equipment in the
categories III and IV the certification body
is a recognised third party organisation.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 9712
Fifth edition
2021-12
Non-destructive testing —
Qualification and certification of NDT
personnel
Essais non destructifs — Qualification et certification du personnel
END
Reference number
ISO 9712:2021(E)
ISO 9712:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 9712:2021(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Abbreviated terms . 6
5 Responsibilities . .6
5.1 General . 6
5.2 Certification body . 6
5.3 Authorized qualification body . 8
5.4 Examination centre . 8
5.5 Employer . 8
5.6 Candidate . 9
5.7 Certificate holders . 9
5.8 Examiners . 10
5.9 Referee . 10
6 Levels of certification .10
6.1 Level 1 . 10
6.2 Level 2 . 10
6.3 Level 3 . 11
7 Eligibility .11
7.1 General . 11
7.2 Training . 11
7.3 Industrial NDT experience.13
7.3.1 General .13
7.3.2 Level 3 . 13
7.3.3 Possible reductions . 14
7.4 Vision requirements — all levels . 14
7.4.1 General . 14
7.4.2 Near vision acuity . 14
7.4.3 Colour vision . 14
7.4.4 Personnel administering vision tests . 15
8 Examinations .15
8.1 Overview . 15
8.1.1 General .15
8.1.2 Examination elements . 15
8.1.3 Examination time . 16
8.1.4 Examination aids . 16
8.2 Examination content and grading for Level 1 and Level 2 . 16
8.2.1 General examination element . 16
8.2.2 Specific examination element . 16
8.2.3 Practical examination element . 16
8.2.4 NDT instruction writing examination element . 17
8.2.5 Grading of the Level 1 and Level 2 examination . 17
8.3 Examination content and grading for Level 3. 18
8.3.1 General . 18
8.3.2 Basic examination element . 18
8.3.3 Main method examination element . 19
8.3.4 Grading of Level 3 examinations . 19
8.4 Conduct of examinations .20
8.5 Re-examination . 20
iii
ISO 9712:2021(E)
8.6 Supplementary examinations . 21
9 Certification .21
9.1 Administration . 21
9.2 Certificates . 21
9.3 Conditions of certification .22
9.3.1 General .22
9.3.2 Granting. 22
9.3.3 Scope extension . 22
9.3.4 Suspension of certification . 22
9.3.5 Withdrawal of certification . 22
9.3.6 Certification after withdrawal. 23
9.3.7 Waiting period prior to certification after withdrawal .23
9.4 Certificates issued by other certification bodies . 23
10 Renewal .23
11 Recertification.24
11.1 General . 24
11.2 Levels 1 and 2 . 25
11.3 Level 3 . 25
12 Files .26
13 Transition period .27
Annex A (normative) Sectors .28
Annex B (normative) Minimum number and type of specimens for the Level 1 and Level 2
practical examination element . .30
Annex C (normative) Structured credit system for renewal Level 1, 2 and 3 and for Level 3
recertification .31
Annex D (normative) Grading practical examination elements .35
Annex E (informative) Engineering of NDT .37
Annex F (informative) Training requirements for techniques .38
Annex G (informative) Psychometric principles .41
Bibliography .42
iv
ISO 9712:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 135, Non-destructive testing,
Subcommittee SC 7, Personnel qualification, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive testing, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This fifth edition cancels and replaces the fourth edition (ISO 9712:2012), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— clarified responsibilities for the certification body, the authorized qualification body, the examination
centre and the employer;
— added and revised definitions;
— defined responsibilities for examiners and referees;
— revised requirements for the duration of training and industrial experience;
— modified requirements for visual acuity testing;
— revised requirements for examinations;
— included an option for the use of a psychometric process at the discretion of the certification body;
— revised requirements for the certification documents;
— revised requirements for the conditions of certification;
— added requirements for candidates for the renewal of certificates;
— revised structured credit system for Level 3 recertification;
— included a new Annex F for techniques;
v
ISO 9712:2021(E)
— included a new Annex G for psychometric principles;
— other minor technical and editorial changes.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
vi
ISO 9712:2021(E)
Introduction
Since the effectiveness of any application of non-destructive testing (NDT) depends upon the
capabilities of the persons who perform or are responsible for the test, a procedure has been developed
to provide a means of evaluating and documenting the competence of personnel whose duties require
the appropriate theoretical and practical knowledge of the non-destructive tests they perform, specify,
supervise, monitor or evaluate. An added incentive stems from the worldwide comparability of a wide
range of industrial applications requiring common non-destructive testing approaches.
When certification of NDT personnel is required in product standards, regulations, codes or
specifications, it is important to certify the personnel in accordance with this document. When
latitude is provided in the criteria within this document, the certification body has the final decision in
determining specific requirements.
When there is no requirement in legislation, in standard or in the order for certification of NDT
personnel, it is for employers of such personnel to decide how to assure themselves that they are
competent to do the work assignments. Thus, they may employ people who are already certified or
they may apply their own expertise so as to assure themselves that their employee has the necessary
competence. In this last case, prudent employers would no doubt use this document as a reference
document.
vii
INTERNATIONAL STANDARD ISO 9712:2021(E)
Non-destructive testing — Qualification and certification of
NDT personnel
1 Scope
This document specifies requirements for the qualification and certification of personnel who perform
industrial non-destructive testing (NDT) in the following methods.
a) acoustic emission testing;
b) eddy current testing;
c) leak testing (hydraulic pressure tests excluded);
d) magnetic testing;
e) penetrant testing;
f) radiographic testing;
g) strain gauge testing;
h) thermographic testing;
i) ultrasonic testing;
j) visual testing (direct unaided visual tests and visual tests carried out during the application of
another NDT method are excluded).
The system specified in this document is also applicable to other NDT methods or to NDT techniques
within an established NDT method, provided a comprehensive scheme of certification exists and
the NDT method or NDT technique is covered by international, regional or national standards or the
NDT method or the NDT technique has been demonstrated to be effective to the satisfaction of the
certification body.
NOTE 1 The term "industrial" implies the exclusion of applications in the field of medicine.
NOTE 2 CEN/TR 14748 provides guidance on the methodology for qualification of non-destructive tests.
NOTE 3 This document specifies requirements for what are, in effect, third party conformity assessment
schemes. These requirements do not directly apply to conformity assessment by second or first parties, but
relevant parts of this document can be referred to in such arrangements.
NOTE 4 The term “direct unaided visual testing” implies where there is an uninterrupted optical path from
the observer’s eye to the test area and the observer uses no tools or devices (e.g. mirror, endoscope, fibre optic).
NOTE 5 Calculations of strain based on other NDT methods are excluded.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 17024:2012, Conformity assessment — General requirements for bodies operating certification of
persons
ISO 9712:2021(E)
ISO 18490:2015, Non-destructive testing — Evaluation of vision acuity of NDT personnel
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
applicant
person who has submitted an application to be admitted into the certification process (3.8)
3.2
authorized qualification body
body, independent of the employer (3.11), authorized by the certification body (3.6) to prepare and
administer examinations (3.12)
3.3
basic examination element
written examination (3.12), at Level 3, which demonstrates the candidate’s (3.4) knowledge of the
materials science and process technology and types of discontinuities, the specific qualification (3.33)
and certification system, and the basic principles of NDT methods (3.25) as required for Level 2
Note 1 to entry: For an explanation of the three levels of qualification, see Clause 6.
Note 2 to entry: The qualification and certification system is specified in this document.
3.4
candidate
applicant (3.1) who has fulfilled specified prerequisites and has been admitted to the certification
process (3.8)
3.5
certificate
document in the form of a letter, card or other medium (e.g. digital certificate), issued by a certification
body (3.6) under the provisions of this document, indicating that the named person has fulfilled the
certification requirements (3.9)
3.6
certification body
body that administers procedures for certification according to specified requirements
3.7
certification cycle
maximum period of time permitted from the date of certification to the date of recertification (3.34)
inclusive of the renewal (3.36) period
3.8
certification process
activities by which a certification body (3.6) determines that a person fulfils certification requirements
(3.9), including application, assessment, decision on certification, renewal (3.36), recertification (3.34)
and use of certificates (3.5) and logos/marks
3.9
certification requirements
set of specified requirements, including requirements of the scheme to be fulfilled in order to establish
or maintain certification
ISO 9712:2021(E)
3.10
competence
ability to apply knowledge and skills to achieve intended results
3.11
employer
legal entity by whom the candidate (3.4) is employed
Note 1 to entry: A candidate may be self-employed.
3.12
examination
mechanism that is part of the assessment which measures a candidate's (3.4) competence (3.10) by one
or more means
3.13
examination centre
centre approved by the certification body (3.6) where examinations (3.12) are carried out
3.14
examination element
component of an examination (3.12)
3.15
examiner
person competent to conduct and score an examination (3.12), where the examination requires
professional judgement
3.16
general examination element
written examination (3.12), at Level 1 or Level 2, concerned with the principles of an NDT method (3.25)
3.17
higher education
formal learning that occurs after completion of secondary education in the field of engineering or
science
3.18
industrial experience
work activities (3.46) performed under supervision (3.45), in the NDT method (3.25) in the sector (3.37)
concerned, needed to acquire the skill and knowledge to fulfil the provisions of qualification (3.33)
3.19
invigilator
proctor
test administrator
person authorized by the certification body (3.6) who supervises an examination (3.12), but does not
evaluate the competence (3.10) of the candidate (3.4)
3.20
job-specific training
training, provided by the employer (3.11) (or their agent) to the certificate (3.5) holder in aspects of
non-destructive testing specific to the employer’s products, NDT equipment, NDT procedures (3.27),
and applicable codes, standards, specifications (3.40) and procedures, leading to the award of operating
authorizations (3.30)
3.21
main method examination element
written examination (3.12), at Level 3, which demonstrates the candidate’s (3.4) general and specific
knowledge, and the ability to write NDT procedures (3.27) for the NDT method (3.25) as applied in the
industrial or product sector(s) (3.37) for which certification is sought
ISO 9712:2021(E)
3.22
multiple choice examination question
wording of a question giving rise to potential replies, only one of which is correct, the remaining being
incorrect or incomplete
3.23
NDT instruction
written description of the precise steps to be followed in testing to an established standard, code,
specification (3.40) or NDT procedure (3.27)
3.24
NDT media
testing products used to create visible indications caused by imperfections or flaws
EXAMPLE Magnetic powder, contrast aid paints, colour contrast penetrant, developer.
3.25
NDT method
discipline applying a physical principle in non-destructive testing
EXAMPLE Ultrasonic testing.
3.26
NDT personnel
personnel who perform non-destructive testing
3.27
NDT procedure
written description of all essential parameters and precautions to be applied when non-destructively
testing products in accordance with standard(s), code(s) or specification(s) (3.40)
3.28
NDT technique
specific way of utilizing an NDT method (3.25)
3.29
NDT training
process of instruction in theory and practice in the NDT method (3.25) in which certification is sought,
which takes the form of training courses to a syllabus approved by the certification body (3.6)
3.30
operating authorization
written statement issued by the employer (3.11), based upon the scope of certification, authorizing the
individual to carry out specified tasks
Note 1 to entry: Such authorization can be dependent on the provision of job-specific training (3.20).
3.31
practical examination element
assessment of practical skills, in which the candidate (3.4) demonstrates familiarity with, and the
ability to perform, the test
3.32
psychometric process
statistical process to verify examinations (3.12) are fair, reliable and discriminate between a competent
and non-competent individual
3.33
qualification
demonstrated education, training, and work experience
ISO 9712:2021(E)
3.34
recertification
process for revalidation of a certificate (3.5) by examination (3.12) or by otherwise satisfying the
certification body (3.6) that the published criteria for recertification have been met
3.35
referee
individual that attests the validity of the candidate’s (3.4) industrial experience (3.18)
3.36
renewal
process for revalidation of a certification at any time up to five years after success in an initial,
supplementary or recertification (3.34) examination (3.12)
3.37
sector
section of industry or technology where specialized NDT practices are used, requiring specific product-
related knowledge, skill, equipment or training
Note 1 to entry: A sector can be interpreted to mean a product (welded products, castings) or an industry
(aerospace, in-service testing). See Annex A.
3.38
significant interruption
absence or change of work activity (3.46) which prevents the certified individual from practising the
duties corresponding to the level in the method and the sector(s) (3.37) within the certified scope, for
either a continuous period in excess of one year, or two or more periods for a total time exceeding two
years
Note 1 to entry: Legal holidays or periods of sickness or training courses of less than 30 days are not taken into
account when calculating the interruption.
3.39
specific examination element
written examination (3.12), at Level 1 or Level 2, concerned with testing techniques applied in a
particular sector(s) (3.37), including knowledge of the product(s) tested and of codes, standards,
specifications (3.40), procedures and acceptance criteria
3.40
specification
document stating requirements
3.41
specimen
sample used in practical examinations (3.12), possibly including radiographs and data sets, which is
representative of products typically tested in the applicable sector (3.37)
Note 1 to entry: A specimen can include more than one area or volume to be tested.
3.42
specimen master report
model answer, indicating the optimum result for a practical examination (3.12) given a specified set
of conditions (equipment type, settings, technique, specimen (3.41), etc.) against which the candidate’s
(3.4) test report is graded
3.43
structured credit system
point system based on the NDT activities of the candidate (3.4) used as an alternative to examination
(3.12) for renewal (3.36) or recertification (3.34)
ISO 9712:2021(E)
3.44
structured experience program
SEP
program approved by the certification body (3.6) to reduce industrial experience (3.18)
3.45
supervision
act of directing the application of NDT performed by other NDT personnel (3.26), which includes the
control of actions involved in the preparation of the test, performance of the test and reporting of the
results
3.46
work activity
performance of NDT-related functions and tasks
Note 1 to entry: See Clause 6.
4 Abbreviated terms
For the purposes of this document, the abbreviated terms listed in Table 1 are used to identify NDT
methods.
Table 1 — Methods and abbreviated terms
NDT method Abbreviated terms
Acoustic emission testing AT
Eddy current testing ET
Leak testing LT
Magnetic testing MT
Penetrant testing PT
Radiographic testing RT
Strain gauge testing ST
Thermographic testing TT
Ultrasonic testing UT
Visual testing VT
5 Responsibilities
5.1 General
The certification system, which shall be controlled and administered by a certification body, includes
all procedures necessary to demonstrate the qualification and the competence of an individual to carry
out tasks in a specific NDT method and product or industrial sector, leading to certification.
5.2 Certification body
5.2.1 The certification body shall fulfil the requirements of ISO/IEC 17024.
5.2.2 The certification body:
a) shall initiate, promote, maintain and administer the certification scheme according to ISO/IEC 17024
and this document;
b) shall be independent of any single interest;
ISO 9712:2021(E)
c) shall be responsible for the definition of sectors (see Annex A);
d) shall publish information regarding the scope of the certification scheme and a general description
of the certification process;
e) shall provide information for training courses that include the syllabi which embody the content of
recognized documents; ISO/TS 25107 or equivalent can be used as guidance;
f) shall conduct an initial audit and subsequent periodic surveillance audits of the authorized
qualification body(ies) to ensure their conformity to the specifications;
g) shall monitor, in accordance with a documented procedure, all delegated functions;
h) shall approve properly staffed and equipped examination centres, which it shall monitor on a
periodic basis;
i) shall administer examinations through approved examination centres;
j) shall bear full responsibilities for examinations conducted on temporary basis at external premises;
k) shall be responsible for ensuring the security of all examination materials (examination specimens,
specimen master reports, question banks, examination papers, etc.) and shall ensure that these
materials are not in use for training purposes;
l) shall be responsible for granting, extension, suspension, withdrawal or revalidation of certification;
m) shall establish an appropriate system for the maintenance of records, which shall be retained for at
least one certification cycle;
n) shall require all candidates and certificate holders to give a signed or stamped undertaking to
abide by a code of ethics which it shall develop for the purpose and publish;
o) may approve training bodies; ISO/TS 25108 can be used as guidance;
p) may delegate, under its direct responsibility, the detailed administration of qualification to
authorized qualification bodies, to which it shall issue specifications and/or procedures covering
facilities, personnel, verification and control of NDT equipment, examination materials, specimens,
conduct of examinations, examination gradi
...