SIST-TS CEN/TS 15534-2:2007

SLOVENSKI STANDARD
01-september-2007
Lesno-polimerni kompoziti (WPC) - 2. del: Karakterizacija WPC materialov
Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials
Holz-Polymer-Werkstoffe (WPC) - Teil 2: Beschreibung von WPC-Werkstoffen
Composites bois-plastiques (WPC) - Partie 2 : Caractérisation des matériaux WPC
Ta slovenski standard je istoveten z: CEN/TS 15534-2:2007
ICS:
79.060.01 /HVQHSORãþHQDVSORãQR Wood-based panels in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN/TS 15534-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2007
ICS 79.060.01
English Version
Wood-plastics composites (WPC) - Part 2: Characterisation of
WPC materials
Composites bois-plastiques (WPC) - Partie 2 : Holz-Kunststoff-Verbundstoffe (WPC) - Teil 2:
Caractérisation des matériaux WPC Beschreibung von WPC-Werkstoffen
This Technical Specification (CEN/TS) was approved by CEN on 29 December 2006 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15534-2:2007: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Characterisation of WPC materials.5
Annex A (informative) Technical data templates .7

Foreword
This document (CEN/TS 15534-2:2007) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by NBN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
CEN/TS 15534 consists of the following parts, under the general title Wood plastics composites (WPC):
 Part 1: Test methods for characterisation of WPC materials and products
 Part 2: Characterisation of WPC materials
 Part 3: Characterisation of WPC products
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

1 Scope
This Technical Specification identifies the required and optional properties of wood-plastics composite (WPC)
materials. It is intended to be used as a basis for the specifications of WPC materials.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 117, Wood preservatives — Determination of toxic values against Reticulitermes species (European
termites) (laboratory method)
EN 317, Particleboards and fibreboards — Determination of swelling in thickness after immersion in water
EN 1534, Wood and parquet flooring — Determination of resistance to indentation (Brinell) — Test method
ENV 12038, Durability of wood and wood-based products — Wood-based panels — Method of test for
determining the resistance against wood-destroying basidiomycetes
CEN/TS 15083-2, Durability of wood and wood-based products — Determination of the natural durability of
solid wood against wood-destroying fungi, test methods — Part 2: Soft rotting micro-fungi
prEN 15458, Paints and varnishes — Laboratory method for testing the efficacy of film preservatives in a
coating against algae
CEN/TS 15534-1:2007, Wood-plastics composites (WPC) — Part 1: Test methods for characterisation of
WPC materials and products
EN ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
(ISO 75-1:2004)
EN ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics, ebonite
and long-fibre-reinforced composites (ISO 75-2:2004)
EN ISO 178, Plastics — Determination of flexural properties (ISO 178:2001)
EN ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
(ISO 179-1:2000)
EN ISO 527-1, Plastics — Determination of tensile
...