SIST EN IEC 61326-2-5:2021

SLOVENSKI STANDARD
01-september-2021
Nadomešča:
SIST EN 61326-2-5:2013
Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za
elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne
konfiguracije, obratovalni pogoji in merila učinkovitosti za delovanje operativnih
naprav s procesnim vodilom v skladu z IEC 61784-1 (IEC 61326-2-5:2020)
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 2-5: Particular requirements - Test configurations, operational conditionsand
performance criteria for field devices with field bus interfaces according to IEC 61784-1
(IEC 61326-2-5:2020)
Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen - Teil 2-5:
Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und
Leistungsmerkmale für Feldgeräte mit Feldbus-Schnittstellen nach IEC 61784-1 (IEC
61326-2-5:2020)
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la
CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de
fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec
les interfaces utilisant des bus de terrain conformes à la CEI 61784-1 (IEC 61326-2-
5:2020)
Ta slovenski standard je istoveten z: EN IEC 61326-2-5:2021
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61326-2-5

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2021
ICS 25.040.40; 17.220.20; 33.100.20 Supersedes EN 61326-2-5:2013 and all of its
amendments and corrigenda (if any)
English Version
Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 2-5: Particular requirements -
Test configurations, operational conditions and performance
criteria for field devices with field bus interfaces according to IEC
61784-1
(IEC 61326-2-5:2020)
Matériel électrique de mesure, de commande et de Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-
laboratoire - Exigences relatives à la CEM - Partie 2-5: Anforderungen - Teil 2-5: Besondere Anforderungen -
Exigences particulières - Configurations d'essai, conditions Prüfanordnungen, Betriebsbedingungen und
de fonctionnement et critères de performance pour les Leistungsmerkmale für Feldgeräte mit Feldbus-
équipements de terrain avec des interfaces utilisant des bus Schnittstellen nach IEC 61784-1
de terrain conformes à l'IEC 61784-1 (IEC 61326-2-5:2020)
(IEC 61326-2-5:2020)
This European Standard was approved by CENELEC on 2020-12-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61326-2-5:2021 E

European foreword
The text of document 65A/978/FDIS, future edition 3 of IEC 61326-2-5, prepared by SC 65A "System
aspects" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61326-2-5:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-06-04
document have to be withdrawn
This document supersedes EN 61326-2-5:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61326-2-5:2020 was approved by CENELEC as a
European Standard without any modification.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZA of EN IEC 61326-1:2021 applies with the following additions:
Publication Year Title EN/HD Year
IEC 61158-2 2014 Industrial communication networks - EN 61158-2 2014
Fieldbus specifications - Part 2: Physical
layer specification and service definition
IEC 61158-3-3 2014 Industrial communication networks - EN 61158-3-3 2014
Fieldbus specifications - Part 3-3: Data-link
layer service definition - Type 3 elements
IEC 61158-5-5 2014 Industrial communication networks - EN 61158-5-5 2014
Fieldbus specifications - Part 5-5:
Application layer service definition - Type 5
elements
IEC 61158-6-10 2019 Industrial communication networks - EN IEC 61158-6-10 2019
Fieldbus specifications - Part 6-10:
Application layer protocol specification -
Type 10 elements
IEC 61326-1 2020 Electrical equipment for measurement, EN IEC 61326-1 2021
control and laboratory use - EMC
requirements - Part 1: General
requirements
IEC 61784-1 2019 Industrial communication networks - EN IEC 61784-1 2019
Profiles Part 1: Fieldbus profiles

IEC 61326-2-5 ®
Edition 3.0 2020-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrical equipment for measurement, control and laboratory use –

EMC requirements –
Part 2-5: Particular requirements – Test configurations, operational conditions

and performance criteria for field devices with field bus interfaces according to

IEC 61784-1
Matériel électrique de mesure, de commande et de laboratoire –

Exigences relatives à la CEM –

Partie 2-5: Exigences particulières – Configurations d'essai, conditions de

fonctionnement et critères de performance pour les équipements de terrain

avec des interfaces utilisant des bus de terrain conformes à l’IEC 61784-1

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20; 25.040.40; 33.100.20 ISBN 978-2-8322-8952-5

– 2 – IEC 61326-2-5:2020 © IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 General . 6
5 EMC test plan . 6
5.1 General . 6
5.2 Configuration of EUT during testing . 6
5.3 Operation conditions of EUT during testing . 6
5.4 Specification of FUNCTIONAL PERFORMANCE . 6
5.5 Test description . 6
6 Immunity requirements . 6
6.1 Conditions during the tests. 6
6.2 Immunity test requirements . 7
6.3 Random aspects . 7
6.4 Performance criteria . 7
7 Emission requirements . 7
8 Test results and test report . 7
9 Instructions for use . 7
Annex A (normative) Immunity test requirements for PORTABLE TEST AND MEASUREMENT
EQUIPMENT powered by battery or from the circuit being measured . 8
Annex B (informative) Guide for analysis and assessment for electromagnetic
compatibility. 9
Annex AA (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 1/1 . 10
AA.1 General . 10
AA.2 EMC test plan . 10
AA.2.1 Configuration of EUT with CP 1/1 interface during testing . 10
AA.2.2 Operation conditions of EUT with CP 1/1 interface during testing . 12
AA.3 Performance criteria . 14
AA.4 Information on the host system . 14
Annex BB (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 3/2 . 15
BB.1 General . 15
BB.2 EMC test plan . 15
BB.2.1 Configuration of EUT with CP 3/2 interface during testing . 15
BB.2.2 Operation conditions of EUT with CP 3/2 interface during testing . 17
BB.3 Performance criteria . 18

Figure AA.1 – Test set up for EUT with CP 1/1 interface . 12
Figure BB.1 – Test set up for EUT with CP 3/2 interface . 17

IEC 61326-2-5:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-5: Particular requirements –
Test configurations, operational conditions and performance criteria
for field devices with field bus interfaces according to IEC 61784-1

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61326-2-5 has been prepared by subcommittee 65A: System
aspects, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This third edition cancels and replaces the second edition published in 2012. This edition
constitutes a technical revision.
This edition includes the following significant technical change with respect to the previous
edition:
– update with respect to IEC 61326-1:2020.

– 4 – IEC 61326-2-5:2020 © IEC 2020
The text of this International Standard is based on the following documents:
FDIS Report on voting
65A/978/FDIS 65A/989/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This part of IEC 61326 series is to be used in conjunction with IEC 61326-1:2020 and follows
the same numbering of clauses, subclauses, tables and figures.
When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in IEC 61326-1 is to be adapted accordingly.
NOTE The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in IEC 61326-1;
– unless notes are in a new subclause or involve notes in IEC 61326-1, they are numbered starting from 101
including those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
A list of all parts of IEC 61326 series, under the general title Electrical equipment for
measurement, control and laboratory use – EMC requirements can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 61326-2-5:2020 © IEC 2020 – 5 –
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-5: Particular requirements –
Test configurations, operational conditions and performance criteria
for field devices with field bus interfaces according to IEC 61784-1

1 Scope
In addition to the requirements of IEC 61326-1, this part of IEC 61326 treats the particular
features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers
only the field bus interface of the equipment.
NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series.
This part refers only to field devices intended for use in process control and process measuring.
In this document, field devices with interfaces according to IEC 61784-1:2019, CP 3/2 and
CP 1/1 as defined in IEC 61784 are covered. Other field bus interfaces may be included in
future editions of this document.
IEC 61784-1:2019 specifies a set of protocol specific communication profiles based on
IEC 61158.
The manufacturer specifies the environment for which the product is intended to be used and/or
selects the appropriate test level specifications of IEC 61326-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
Clause 2 of IEC 61326-1:2020 applies except as follows:
Addition:
IEC 61158-2:2014, Industrial communication networks – Fieldbus specifications – Part 2:
Physical layer specification and service definition
IEC 61158-3-3:2014, Industrial communication networks – Fieldbus specifications – Part 3-3:
Data-link layer service definition – Type 3 elements
IEC 61158-5-5:2014, Industrial communication networks – Fieldbus specificat
...