oSIST prEN ISO 19085-15:2026

SLOVENSKI STANDARD
01-september-2026
Lesnoobdelovalni stroji - Varnost - 15. del: Stiskalnice (ISO/DIS 19085-15:2026)
Woodworking machines - Safety - Part 15: Presses (ISO/DIS 19085-15:2026)
Holzbearbeitungsmaschinen - Sicherheit - Teil 15: Pressen (ISO/DIS 19085-15:2026)
Machines à bois - Sécurité - Partie 15: Presses (ISO/DIS 19085-15:2026)
Ta slovenski standard je istoveten z: prEN ISO 19085-15
ICS:
13.110 Varnost strojev Safety of machinery
25.120.10 Kovaški stroji. Stiskalnice. Forging equipment. Presses.
Škarje Shears
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 19085-15
ISO/TC 39/SC 4
Woodworking machines — Safety —
Secretariat: UNI
Part 15:
Voting begins on:
Presses 2026-07-27
Voting terminates on:
Machines à bois — Sécurité —
2026-10-19
Partie 15: Presses
ICS: 13.110; 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document has not been edited by the ISO Central Secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 19085-15:2026(en)
DRAFT
ISO/DIS 19085-15:2026(en)
International
Standard
ISO/DIS 19085-15
ISO/TC 39/SC 4
Woodworking machines — Safety —
Secretariat: UNI
Part 15:
Voting begins on:
Presses
Voting terminates on:
Machines à bois — Sécurité —
Partie 15: Presses
ICS: 13.110; 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document has not been edited by the ISO Central Secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2026
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 19085-15:2026(en)
ii
ISO/DIS 19085-15:2026(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Safety requirements and measures for controls . 14
4.1 Safety and reliability of control systems.14
4.2 Control devices .14
4.2.1 General .14
4.2.2 Hand-held control set .14
4.2.3 Reset device .14
4.3 Start .14
4.3.1 Direct start .14
4.3.2 Start via control power-on .14
4.4 Safe stops . 15
4.4.1 Stop function . 15
4.4.2 Normal stop . 15
4.4.3 Operational stop . 15
4.4.4 Emergency stop . 15
4.5 Braking function of tools . 15
4.6 Operating modes . 15
4.7 Tool speed . 15
4.8 Failure of any energy supply . 15
4.9 Manual reset control .16
4.10 Standstill detection .16
4.11 Machine moving parts speed monitoring.16
4.12 Time delay.16
4.13 Teleservice .16
4.14 Protection against corruption .16
5 Safety requirements and protective measures against mechanical hazards .16
5.1 Stability .16
5.2 Risk of break-up during operation .17
5.3 Tool holder and tool design .17
5.4 Tool brake . .17
5.5 Safeguards .18
5.5.1 Fixed guards .18
5.5.2 Interlocking moveable guards .18
5.5.3 Hold-to-run control .18
5.5.4 Two hand control .18
5.5.5 Electro-sensitive protective equipment (ESPE) .18
5.5.6 Pressure sensitive protective equipment (PSPE) .18
5.6 Prevention of access to hazardous moving parts .18
5.6.1 Safeguarding machines with manual loading and unloading .18
5.6.2 Safeguarding machines with high-frequency system .19
5.6.3 Safeguarding machines with automatic workpiece loading/unloading systems
type 1, type 2 and type 3 . 20
5.6.4 Safeguarding machines with automatic workpiece loading/unloading systems
type 4 and type 5 . 20
5.6.5 Safeguarding machines with automatic workpiece loading/unloading system
type 6 .21
5.7 Impact hazard . 22
5.8 Clamping devices . 22
5.9 Measures against ejection . 22

iii
ISO/DIS 19085-15:2026(en)
5.10 Workpiece support and guides . 23
5.10.1 General . 23
5.10.2 Roller tables . 23
5.10.3 Roller rails . 23
6 Safety requirements and protective measures against other hazards .23
6.1 Fire . 23
6.2 Noise . 23
6.2.1 Noise reduction at the design stage . 23
6.2.2 Noise emission measurement and declaration . 23
6.3 Emission of chips and dust .24
6.4 Electricity .24
6.5 Ergonomics and handling . 25
6.6 Lighting . 25
6.7 Pneumatics . 26
6.8 Hydraulics . 26
6.9 Electromagnetic compatibility. 26
6.10 Laser . 26
6.11 Static electricity. 26
6.12 Errors of fitting . 26
6.13 Isolation . 26
6.14 Maintenance . 26
6.15 Relevant but not significant hazards . 26
6.16 Extreme temperatures . 26
6.17 Radiation . 26
7 Information .27
7.1 Warning devices .27
7.2 Marking .27
7.2.1 Marking principles and methods .27
7.2.2 Marking content .27
7.3 Instructions for use . 28
7.3.1 Instructions principles and drafting . 28
7.3.2 Instructions content . 28
7.4 Sales Literature . 28
Annex A (informative) List of significant hazards .29
Annex B (informative) Performance level required .31
Annex C (informative) Brake test .32
Annex D (informative) Impact test for guards .33
Annex E (normative) Noise test code .34
Annex ZA (informative) ZA Relationship between this European Standard and the essential
requirements of Regulation (EU) 2023/1230 aimed to be covered .38
Bibliography .40

iv
ISO/DIS 19085-15:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 4,
Woodworking machines, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 142, Woodworking machines - Safety, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This document is intended to be used in conjunction with ISO DIS 19085-1:2025.
This third edition cancels and replaces the second edition (ISO 19085-15:2025), which has been technically
revised. The main changes are as follows:
— the way of reference from this document to ISO DIS 19085-1:2025 has been simplified, as well as its
explanation in Introduction, and aligned to ISO drafting rules;
— the verification methods at the end of each subclause have been deleted, since self-evident;
— 4.2, 7.2, 7.3 have been rearranged, to follow the new subdivision in ISO DIS 19085-1:2025;
A list of all parts in the ISO 19085 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

v
ISO/DIS 19085-15:2026(en)
Introduction
The ISO 19085 series of International Standards provides technical safety requirements for the design and
construction of woodworking machinery, as well as for the content of the relevant instruction handbook. It
concerns designers, manufacturers, suppliers and importers of the machines specified in the Scope.
This document is a type-C standard as stated in ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organisations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
In this document, a subclause can refer to the same subclause of ISO DIS 19085-1:2025 or give specific
requirements or both.
vi
DRAFT International Standard ISO/DIS 19085-15:2026(en)
Woodworking machines — Safety —
Part 15:
Presses
1 Scope
This document specifies the safety requirements and measures for
— cold presses,
— hot presses,
— bending presses,
— edge/face gluing presses,
— membrane presses, and
— embossing presses,
where the pressing force is applied by hydraulic, pneumatic or electrical actuators pushing two flat or shaped
surfaces against each other, capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A,
relevant to machines, when used as intended and under conditions of misuse which are reasonably
foreseeable, as well as when it is transported, assembled, adjusted, maintained, disabled, dismantled and
scrapped.
The machines are designed to process workpieces consisting of:
— solid wood;
— materials with similar characteristics to wood (see ISO DIS 19085-1:2025, 3.2), except those with light
alloy laminates or edges or profiles for high-frequency presses;
— engineered wood (wood-based material) such as particleboard, fibreboard and plywood composed or
laminated with steel sheets or edges or profiles, except for high-frequency presses;
— honeycomb board;
— composite boards made from the materials listed above.
This document is applicable to machines fitted with one or more of the following devices or additional
working units, whose hazards have been dealt with:
a) a device for hot gluing;
b) a device for high-frequency gluing in the frequency range from 1 MHz to 400 MHz;
c) a device for high-frequency shaping in the frequency range from 1 MHz to 400 MHz;
d) an automatic workpiece loading and unloading system;
e) an intermediate additional platen;
f) a workpiece extractor;
ISO/DIS 19085-15:2026(en)
g) a horizontal pressing system;
h) split moveable platens.
This document does not deal with any hazards related to:
— specific devices that differ from the list above;
— hot fluid heating systems internal to the machine other than electrical;
— hot fluid heating systems of any type external to the machine;
— operation of taking intermediate platens out and in again;
— the combination of a single machine being used with any other machine (as part of a line).
This document is not applicable to:
— carcass clamps;
— membrane presses where the pressing force is applied by vacuum only;
— presses for producing particleboard, fibreboard, OSB;
— machines intended for use in potentially explosive atmosphere;
— machines manufactured before the date of publication of this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 7010:2019, Graphical symbols — Safety colours and safety signs — Registered safety signs
ISO 7010:2019/Amd 1:2020, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 1
ISO 7010:2019/Amd 2:2020, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 2
ISO 7010:2019/Amd 3:2021, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 3
ISO 7010:2019/Amd 4:2021, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 4
ISO 7010:2019/Amd 5:2022, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 5
ISO 7010:2019/Amd 6:2022, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 6
ISO 7010:2019/Amd 7:2023, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 7
ISO 7010:2019/Amd 8:2024, Graphical symbols — Safety colours and safety signs — Registered safety signs —
Amendment 8
ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 13850:2015, Safety of machinery — Emergency stop function — Principles for design

ISO/DIS 19085-15:2026(en)
ISO 13855:2024, Safety of machinery — Positioning of safeguards with respect to the approach of the human
body
ISO/DIS 19085-1:2025, Woodworking machines — Safety — Part 1: Common requirements
IEC 60204-1:2016, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
IEC 61310-1:2007, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for visual,
acoustic and tactile signals
IEC 62311:2019, Assessment of electronic and electrical equipment related to human exposure restrictions for
electromagnetic fields (0 Hz to 300 GHz)
E N 12198 -1:2000 +A 1: 2008 , Safety of machinery — Assessment and reduction of risks arising from radiation
emitted by machinery — Part 1: General principles
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12100:2010, ISO 13849-1:2023,
ISO DIS 19085-1:2025 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
cold press
machine used to laminate or join together flat panels, or both, in which the pressing force is applied by
hydraulic, pneumatic or electrical actuators pushing two cold flat platens against each other
Note 1 to entry: The moveable platen can be the top or the bottom one or both. Examples of different machine designs
are illustrated in Figures 1 and 2 (safeguarding devices are not fully illustrated).
Note 2 to entry: The following devices can be provided:
— automatic panel loading and unloading;
— split moveable platens (see Figure 14).
3.2
hot press
machine used to laminate or join together flat panels, or both, in which the pressing force is applied by
hydraulic actuators pushing two hot flat platens against each other
Note 1 to entry: The moveable platen can be the top or the bottom one or both. Examples of different machine designs
are illustrated in Figures 1 and 2 (safeguarding devices are not fully illustrated).
Note 2 to entry: The following devices can be provided:
— automatic panel loading and unloading;
— intermediate additional platens (see Figure 3).
Note 3 to entry: Platens heating systems can be by electrical resistance or hot fluid (e.g. diathermic oil, water). Fluid
heating system can be internal to the machine or external.

ISO/DIS 19085-15:2026(en)
Figure 1 — Example of a cold or hot press with bottom actuators
Figure 2 — Example of a cold or hot press with top actuators

ISO/DIS 19085-15:2026(en)
Figure 3 — Example of a hot press with intermediate platens
3.3
bending press
machine with manual loading or unloading or both used to assembly or shape flat panels, or both, in which
the pressing force is applied by hydraulic actuators pushing two shaped surfaces against each other, and the
hot gluing process is by hot dies or high-frequency system
Note 1 to entry: For an example, see Figure 4 (safeguarding devices are not fully illustrated).

ISO/DIS 19085-15:2026(en)
Figure 4 — Example of a bending press with top actuators
3.4
edge/face gluing press
machine used to join together solid wood bars, in which the pressing force is applied by hydraulic, pneumatic
or electrical actuators vertically pushing two flat platens against each other, and horizontally pushing
elements against each other, and the gluing process is by hot platens or high-frequency system or as a cold
press with adequate adhesives
Note 1 to entry: The following devices can be provided:
— workpieces extractor;
— automatic panel loading and unloading system;
— horizontal pressing system (3.15).
Note 2 to entry: For an example, see Figure 5 (safeguarding devices are not fully illustrated).

ISO/DIS 19085-15:2026(en)
a) “Bridge” type b) “Cantilever” type
Figure 5 — Example of an edge/face gluing press
3.5
membrane press
machine used to laminate or veneer flat or shaped workpieces, in which the pressing force is applied
through a membrane pushed onto the workpiece by compressed air from above and by vacuum from below,
hermetically enclosed by two shells, of which the upper one is heated, pushed against each other by hydraulic
actuators
Note 1 to entry: Automatic panel loading and unloading devices can be provided.
Note 2 to entry: Upper shell heating systems can be by electrical resistance or hot fluid (e.g. diathermic oil, water).
Fluid heating system can be internal to the machine or external.
Note 3 to entry: For an example, see Figure 6 (safeguarding devices are not fully illustrated).

ISO/DIS 19085-15:2026(en)
Figure 6 — Example of a membrane press
3.6
embossing press
machine used to emboss workpieces by a special mould or die fixed to the upper plate, in which the pressing
force is applied by hydraulic actuators pushing two hot flat platens against each other
Note 1 to entry: The moveable platen can be the top or the bottom one or both. Examples of different machine designs
are illustrated in Figures 1 and 2 (safeguarding devices are not fully illustrated).
Note 2 to entry: Automatic panel loading and unloading devices can be provided.
Note 3 to entry: Platens heating systems can be by electrical resistance or hot fluid (e.g. diathermic oil, water). Fluid
heating system can be internal to the machine or external.
3.7
daylight
compartment between two consecutive pressing platens
3.8
automatic workpiece loading/unloading system
system for automatic dragging workpieces into or out of the machine, whereby the workpiece is manually
loaded onto or unloaded from the system itself
Note 1 to entry: Six usual types of automatic workpiece loading/unloading systems are considered in this document.
3.9
automatic workpiece loading/unloading system type 1
system consisting of an automatic belt or chain or roller conveyor for loading workpieces into the daylight
(3.7), a feeding belt or chain or roller device applied to the bottom platen and idle roller conveyor or an
automatic belt or chain or roller conveyor for unloading workpieces
Note 1 to entry: For an example, see Figure 7 (safeguarding devices are not fully illustrated).

ISO/DIS 19085-15:2026(en)
Key
1 automatic belt conveyor for loading
2 feeding belt device applied to the bottom platen
3 idle roller conveyor for unloading
4 feed direction
Figure 7 — Example of an automatic workpiece loading/unloading system type 1
3.10
automatic workpiece loading/unloading system type 2
system similar to automatic workpiece loading/unloading system type 1 (3.9) but with an automatic hybrid
chain and belt feeding device applied to the platens
Note 1 to entry: For an example, see Figure 8 (safeguarding devices are not fully illustrated).
Key
1 hybrid chain and belt feeding device
2 feed direction
3 shaft for feeding belt tensioning
Figure 8 — Example of a hybrid chain and belt device

ISO/DIS 19085-15:2026(en)
3.11
automatic workpiece loading/unloading system type 3
system consisting of an automatic pusher for loading workpieces into the daylight (3.7)
Note 1 to entry: Loading a workpiece into the daylight pushes out the previous workpiece.
Note 2 to entry: Unloading support can be either inclined idle roller conveyor or horizontal table.
Note 3 to entry: See Figure 9 for an example with an unloading inclined idle roller conveyor (safeguarding devices are
not fully illustrated).
Key
1 automatic pusher
2 feed direction
3 platens
Figure 9 — Example of an automatic workpiece loading/unloading system type 3
3.12
automatic workpiece loading/unloading system type 4
system consisting of an automatic sliding belt conveyor for loading workpieces into the daylight (3.7) and for
unloading workpieces onto a roller conveyor
Note 1 to entry: When the sliding belt conveyor loads a workpiece into the daylight, at the same time it pushes out any
workpiece previously in the daylight.
Note 2 to entry: For an example, see Figure 10.

ISO/DIS 19085-15:2026(en)
Key
1 sliding belt conveyor
2 loaded workpiece
3 unloaded workpiece
4 platens
5 unloading roller conveyor
Figure 10 — Example of an automatic workpiece loading/unloading system type 4
3.13
automatic workpiece loading/unloading system type 5
system consisting of an automatic sliding belt conveyor for loading workpieces in the daylight (3.7) in
combination with a vacuum system for unloading workpieces onto a roller conveyor
Note 1 to entry: For an example, see Figure 11.
Key
1 sliding belt conveyor
2 loaded workpiece
3 unloaded workpiece
4 platens
5 vacuum system for unloading
6 unloading roller conveyor
Figure 11 — Example of an automatic workpiece loading/unloading system type 5

ISO/DIS 19085-15:2026(en)
3.14
automatic workpiece loading/unloading system type 6
system consisting of an automatic belt or roller multi-conveyor for loading workpieces in a multi-daylight
machine, a feeding belt or chain or roller device applied to the platens and an automatic belt or roller multi-
conveyor for unloading workpieces
Note 1 to entry: Each single conveyor of the multi-conveyor (see Figure 12 Keys 2 and 5) can move up and down in
order to align with daylights (3.7).
Note 2 to entry: Multi-conveyors are loaded/unloaded by single automatic belt or roller conveyors.
Note 3 to entry: For an example, see Figure 12 (safeguarding devices are not fully illustrated).
Key
1 single load belt conveyor
2 automatic belt multi-conveyor for loading
3 multi-daylight machine
4 feeding belt devices applied to the platens
5 automatic belt multi-conveyor for unloading
6 roller conveyor for unloading
7 feed direction
Figure 12 — Example of an automatic workpiece loading/unloading system type 6
3.15
horizontal pressing system
system consisting of horizontal pressing elements, together with a beam and a platen that clamp the
workpieces in position from above before the horizontal pressing elements close
Note 1 to entry: For an example, see Figure 13.

ISO/DIS 19085-15:2026(en)
Figure 13 — Examples of horizontal pressing system
3.16
split movable platen
platen, covering the whole working area, divided into sections that move independently, to process smaller
workpieces of different heights at the same time
Note 1 to entry: The split platen can be top or bottom.
Note 2 to entry: For an example, see Figure 14 (safeguarding devices are not fully illustrated).
Figure 14 — Example of a cold press with split moveable platen
3.17
jog
control device for momentary activation of a function or a movement

ISO/DIS 19085-15:2026(en)
4 Safety requirements and measures for controls
4.1 Safety and reliability of control systems
ISO DIS 19085-1:2025, 4.1, shall apply.
Annex B, Table B.1 summarizes the performance levels required (PL ) in Clauses 4 and 5 for all safety
r
functions.
4.2 Control devices
4.2.1 General
ISO DIS 19085-1:2025, 4.2.1, shall apply.
The main electrical control devices of the machine for control power-on, jog, normal stop, two-hand control
and integrated fee
...