oSIST prEN ISO 8233:2020

SLOVENSKI STANDARD
01-oktober-2020
Plastomerni ventili - Vrtilni moment - Preskusna metoda (ISO/DIS 8233:2020)
Thermoplastics valves - Torque - Test method (ISO/DIS 8233:2020)
Armaturen aus Thermoplasten - Drehmoment - Prüfverfahren (ISO/DIS 8233:2020)
Robinets en matériaux thermoplastiques - Couple de manoeuvre - Méthode d’essai
(ISO/DIS 8233:2020)
Ta slovenski standard je istoveten z: prEN ISO 8233
ICS:
23.060.01 Ventili na splošno Valves in general
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 8233
ISO/TC 138/SC 7 Secretariat: UNI
Voting begins on: Voting terminates on:
2020-08-17 2020-11-09
Thermoplastics valves — Torque — Test method
Robinets en matériaux thermoplastiques — Couple de manoeuvre — Méthode d'essai
ICS: 83.140.30; 23.060.01
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8233:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

ISO/DIS 8233:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO/DIS 8233:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specimen . 2
5 Test condition . 2
6 Apparatus . 3
7 Procedure for torque test . 3
8 Test report . 4
Bibliography . 5
ISO/DIS 8233:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 07, Valves and auxiliary equipment of plastics materials.
This second edition cancels and replaces the first edition (ISO 8233:1988), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— updating of the normative references and terms and definitions clauses;
— specification of the type of valve in the test report and explanation for the opening torque.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

ISO/DIS 8233:2020(E)
Introduction
The aim of this document is to establish certain basic requirements for the torque testing of plastics
valves to ensure that uniform test methods are adopted. This document is intended to be considered in
conjunction with any specific requirements in particular product standards applicable to the individual
types of valves.
DRAFT INTERNATIONAL STANDARD ISO/DIS 8233:2020(E)
Thermoplastics valves — Torque — Test method
1 Scope
This International Standard specifies a test method for the determi
...