EN ISO 25137-2:2017

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Polimerni materiali - Sulfonski polimerni materiali za brizganje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 25137-2:2009)Kunststoffe - Sulfonpolymer-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 25137-2:2009)Plastiques - Matériaux pour moulage et extrusion à base de polymères sulfone - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 25137-2:2009)Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009)83.080.20PlastomeriThermoplastic materialsICS:Ta slovenski standard je istoveten z:EN ISO 25137-2:2017SIST EN ISO 25137-2:2017en,fr,de01-marec-2017SIST EN ISO 25137-2:2017SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 25137-2
January
t r s y ICS
z uä r z rä t r English Version
Plastics æ Sulfone polymer moulding and extrusion materials æ Part
tã Preparation of test specimens and determination of propePlastiques æ Matériaux pour moulage et extrusion à base de polymères sulfone æ Partie
tã Préparation des
Kunststoffe æ SulfonpolymeræWerkstoffe æ Teil
tã Herstellung von Probekörpern und Bestimmung von This European Standard was approved by CEN on
t r December
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN ISO
t w s u yæ tã t r s y ESIST EN ISO 25137-2:2017

Reference numberISO 25137-2:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO25137-2First edition2009-01-15Plastics — Sulfone polymer moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties Plastiques — Matériaux pour moulage et extrusion à base de polymères sulfone — Partie 2: Préparation des éprouvettes et détermination des propriétés
ISO 25137-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
ISO 25137-2:2009(E) © ISO 2009 – All rights reserved
iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Preparation of test specimens.3 3.1 General.3 3.2 Treatment of the material before moulding.3 3.3 Injection moulding.3 4 Conditioning of test specimens.3 5 Determination of properties.3
ISO 25137-2:2009(E) iv
INTERNATIONAL STANDARD ISO 25137-2:2009(E) © ISO 2009 – All rights reserved
1Plastics — Sulfone polymer moulding and extrusion materials — Part 2: Preparation of test specimens and determination
...