ISO 62:2008
(Main)Plastics — Determination of water absorption
Plastics — Determination of water absorption
ISO 62:2008 describes a procedure for determining the moisture absorption properties in the “through-the-thickness” direction of flat or curved-form solid plastics. It also describes procedures for determining the amount of water absorbed by plastic specimens of defined dimensions, when immersed in water or when subjected to humid air under controlled conditions. The “through-the-thickness” moisture diffusion coefficient can be determined for single-phase material by assuming Fickian diffusion behaviour with constant moisture absorption properties through the thickness of the test specimen. This model is valid for homogeneous materials and for reinforced polymer-matrix composites tested below their glass transition temperature. However, some two-phase matrices such as hardened epoxies may require a multi-phase absorption model which is not covered by this International Standard. The results obtained using the methods described in this International Standard are applicable to most plastics but are not applicable to cellular plastics, granulates or powders, which can show additional absorption and capillary effects. Plastics exposed to moisture under controlled conditions for defined periods of time provide relative comparisons between them.
Plastiques — Détermination de l'absorption d'eau
L'ISO 62:2008 décrit un mode opératoire permettant de déterminer les propriétés d'absorption de l'humidité dans l'épaisseur de matériaux plastiques solides plats ou courbes. La présente norme décrit également des modes opératoires permettant de déterminer la quantité d'eau absorbée par des éprouvettes de dimensions définies, immergées dans l'eau ou exposées à de l'air humide dans des conditions définies. Le calcul du coefficient de diffusion de l'humidité dans l'épaisseur suppose un matériau fickien monophasé ayant des propriétés constantes d'absorption d'humidité dans l'épaisseur de l'éprouvette. Ce modèle est valable pour les matériaux homogènes et pour les composites renforcés à matrice polymère soumis à essai au-dessous de leur température de transition vitreuse. Toutefois, certaines matrices à deux phases, telles que les époxydes durcis, peuvent nécessiter un modèle d'absorption multiphase qui n'est pas couvert par la présente Norme internationale. Les résultats obtenus en utilisant les méthodes décrites dans l'ISO 62:2008 s'appliquent à la plupart des plastiques, à l'exception des plastiques alvéolaires, des granulés ou des poudres qui peuvent avoir d'autres effets capillaires et d'absorption. Des expositions pendant un laps de temps fixe permettent des comparaisons relatives des plastiques. Les essais décrits pour la détermination du coefficient de diffusion peuvent ne pas être applicables à tous les plastiques. Les plastiques ne pouvant pas garder leur forme lors de leur exposition à l'eau bouillante ne peuvent pas être comparés en utilisant la méthode 2.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 62
Third edition
2008-02-15
Plastics — Determination of water
absorption
Plastiques — Détermination de l'absorption d'eau
Reference number
©
ISO 2008
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Principle. 2
4 Apparatus . 2
5 Test specimens . 2
5.1 General. 2
5.2 Square-shaped test specimens for homogeneous plastics. 3
5.3 Test specimens of reinforced plastics affected by anisotropic diffusion effects. 3
5.4 Tubular test specimens. 3
5.5 Rod-shaped test specimens . 4
5.6 Specimens cut from finished products, extrusion compounds, sheets or laminates . 4
6 Test conditions and procedures . 4
6.1 General. 4
6.2 General conditions . 4
6.3 Method 1: Determination of amount of water absorbed after immersion in water at 23 °C. 5
6.4 Method 2: Determination of amount of water absorbed after immersion in boiling water . 5
6.5 Method 3: Determination of water-soluble matter lost during immersion. 6
6.6 Method 4: Determination of amount of water absorbed after exposure to 50 % relative
humidity . 6
7 Expression of results . 6
7.1 Percentage by mass of water absorbed. 6
7.2 Determination of the water content at saturation and the water diffusion coefficient using
Fick’s laws. 7
8 Precision. 8
9 Test report . 9
Annex A (informative) Correlation between water absorption by test specimens and Fick’s
diffusion laws. 10
Annex B (informative) Precision statement. 12
Bibliography . 15
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 62 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 6, Ageing, chemical
and environmental resistance.
This third edition cancels and replaces the second edition (ISO 62:1999), to which a precision statement has
been added.
iv © ISO 2008 – All rights reserved
Introduction
Plastics exposed to water are subject to several different effects:
a) dimensional changes (e.g. swelling) caused by absorption of water;
b) extraction of water-soluble components;
c) changes in other properties.
However, exposure to humidity, immersion and exposure to boiling water can result in distinctly different
material responses. The equilibrium moisture content can be used to compare the amount of water absorbed
by different types of plastics when they are exposed to moisture. Moisture content determined under non-
equilibrium conditions can be used to compare different batches of the same material and to determine the
diffusion constant of the material when determined under carefully controlled non-equilibrium conditions of
exposure to moisture and when using plastic specimens of defined dimensions.
INTERNATIONAL STANDARD ISO 62:2008(E)
Plastics — Determination of water absorption
1 Scope
1.1 This International Standard describes a procedure for determining the moisture absorption properties in
the “through-the-thickness” direction of flat or curved-form solid plastics. This International Standard also
describes procedures for determining the amount of water absorbed by plastic specimens of defined
dimensions, when immersed in water or when subjected to humid air under controlled conditions. The
“through-the-thickness” moisture diffusion coefficient can be determined for single-phase material by
assuming Fickian diffusion behaviour with constant moisture absorption properties through the thickness of
the test specimen. This model is valid for homogeneous materials and for reinforced polymer-matrix
composites tested below their glass transition temperature. However, some two-phase matrices such as
hardened epoxies may require a multi-phase absorption model which is not covered by this International
Standard.
1.2 Ideally, the best comparison of the water absorption properties and/or diffusion coefficients of materials
should be carried out only using the equilibrium moisture content of plastics exposed to identical conditions.
The comparison of materials using properties at moisture equilibrium does not assume, and is therefore not
limited to, single-phase Fickian diffusion behaviour.
1.3 Alternatively, water absorption of plastic specimens of defined dimensions exposed to immersion or
humidity under controlled conditions but for an arbitrary time period can be used to compare different batches
of the same material or for quality control tests of a given material. For this type of comparison, it is essential
that all test specimens be of identical dimensions and, as nearly as possible, have the same physical
attributes, e.g. surface smoothness, internal stresses, etc. However, moisture equilibrium is not reached under
these conditions. Therefore, results from this type of test cannot be used to compare the water absorption
properties of different types of plastics. For more reliable results, simultaneous tests are recommended.
1.4 The results obtained using the methods described in this International Standard are applicable to most
plastics but are not applicable to cellular plastics, granulates or powders, which can show additional
absorption and capillary effects. Plastics exposed to moisture under controlled conditions for defined periods
of time provide relative comparisons between them. The tests described for the determination of the diffusion
coefficient may not be applicable to all plastics. Plastics that do not retain their shape when immersed in
boiling water should not be compared using method 2 (see 6.4).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 175:1999, Plastics — Methods of test for the determination of the effects of immersion in liquid chemicals
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
ISO 2818, Plastics — Preparation of test specimens by machining
3 Principle
Test specimens are immersed in distilled water at 23 °C or in boiling distilled water, or exposed to 50 %
relative humidity at given temperatures, for prescribed periods. The amount of water absorbed by each test
specimen is determined by measuring its change in mass, i.e. the difference between its initial mass and that
after exposure to water, the change being expressed as a percentage of the initial mass. If required, the
amount of water lost after drying the test specimens can also be determined.
In some applications, 70 % to 90 % relative humidity and temperatures of 70 °C to 90 °C may be necessary.
Relative humidities and temperatures higher than those recommended in this International Standard may be
used by agreement between the interested parties. When relative humidity and temperature conditions other
than those recommended are used, a complete description of these conditions (with appropriate tolerances)
shall be included in the test report.
4 Apparatus
4.1 Balance, with an accuracy of ± 0,1 mg (see also 6.1.3).
4.2 Oven, with forced-air convection or vacuum, maintained at (50,0 ± 2,0) °C or at any other agreed
temperature (see also 6.1.2).
4.3 Containers, containing distilled water or water of equivalent purity, equipped with a means of heating
capable of maintaining the temperature specified.
4.4 Desiccator, with a desiccant (e.g. P O ).
2 5
4.5 Means of measuring the dimensions of the test specimens to an accuracy of ± 0,1 mm, if required.
5 Test specimens
5.1 General
For each material evaluated, test at least three test specimens. Test specimens of the required dimensions
may be prepared by moulding or extrusion. The methods used for preparation of all test specimens shall be
included in the test report.
NOTE The results of this method may be influenced by surface effects. For some materials, different results can be
obtained between moulded specimens and specimens cut from a larger sheet.
Any contaminant on the test specimen surface which could influence water absorption shall be removed by a
cleaning agent which does not attack the plastic, the degree of attack being determined in accordance with
ISO 175 — for example, the notation “none” (no change in appearance) in ISO 175:1999, Table 1. Allow
specimens to dry at 23 °C and 50 % relative humidity for at least 2 h after cleaning and before beginning the
test. Wear clean gloves when handling test specimens to prevent contamination.
The cleaning agent shall have no effect on the the water absorption. When determining the moisture
equilibrium content in accordance wit
...
NORME ISO
INTERNATIONALE 62
Troisième édition
2008-02-15
Plastiques — Détermination de
l'absorption d'eau
Plastics — Determination of water absorption
Numéro de référence
©
ISO 2008
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2008
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2008 – Tous droits réservés
Sommaire Page
Avant-propos. iv
Introduction . v
1 Domaine d'application. 1
2 Références normatives . 1
3 Principe. 2
4 Appareillage . 2
5 Éprouvettes . 2
5.1 Généralités . 2
5.2 Éprouvettes carrées de plastiques homogènes. 3
5.3 Éprouvettes de plastiques renforcés affectés par des effets de diffusion anisotrope . 3
5.4 Éprouvettes tubulaires. 3
5.5 Éprouvettes en forme de jonc . 4
5.6 Éprouvettes découpées dans des profilés finis, des mélanges pour extrusion,
des feuilles ou des stratifiés. 4
6 Conditions d'essai et modes opératoires . 4
6.1 Généralités . 4
6.2 Conditions générales . 4
6.3 Méthode 1: Détermination de l'absorption d'eau après immersion dans l'eau à 23 °C. 5
6.4 Méthode 2: Détermination de l'absorption d'eau après immersion dans l'eau bouillante. 5
6.5 Méthode 3: Détermination de la perte de matières solubles dans l'eau au cours
de l'immersion. 6
6.6 Méthode 4: Détermination de l'absorption d'eau après exposition à une humidité relative
de 50 %. 6
7 Expression des résultats . 6
7.1 Pourcentage en masse d'eau absorbée .6
7.2 Détermination de l'absorption d'eau à saturation et du coefficient de diffusion
selon la théorie de Fick . 7
8 Fidélité . 9
9 Rapport d'essai . 9
Annexe A (informative) Corrélation entre l'absorption d'eau par les éprouvettes et la théorie
de Fick. 10
Annexe B (informative) Énoncé concernant la fidélité . 12
Bibliographie . 15
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 62 a été élaborée par le comité technique ISO/TC 61, Plastiques, sous-comité SC 6, Vieillissement et
résistance aux agents chimiques et environnants.
Cette troisième édition annule et remplace la deuxième édition (ISO 62:1999), à laquelle a été ajouté un
énoncé concernant la fidélité.
iv © ISO 2008 – Tous droits réservés
Introduction
Les plastiques exposés à l'eau sont soumis à plusieurs actions différentes:
a) des modifications dimensionnelles (par exemple gonflement) provoquées par l'absorption d'eau;
b) l'extraction des éléments solubles dans l'eau;
c) des modifications d'autres propriétés.
Toutefois, l'exposition à l'humidité, l'immersion et l'exposition à de l'eau bouillante peuvent entraîner des
réponses nettement différentes du matériau. La teneur en eau à l'équilibre peut permettre de comparer la
quantité d'eau absorbée par différents types de plastiques exposés à l'humidité. Une exposition
soigneusement contrôlée, mais non équilibrée, d'éprouvettes de plastique ayant des dimensions définies peut
être utilisée pour comparer différents lots d'un même matériau et déterminer la constante de diffusion du
matériau soumis à essai.
NORME INTERNATIONALE ISO 62:2008(F)
Plastiques — Détermination de l'absorption d'eau
1 Domaine d'application
1.1 La présente Norme internationale spécifie un mode opératoire permettant de déterminer les propriétés
d'absorption de l'humidité dans l'épaisseur de matériaux plastiques solides plats ou courbes. La présente
norme décrit également des modes opératoires permettant de déterminer la quantité d'eau absorbée par des
éprouvettes de dimensions définies, immergées dans l'eau ou exposées à de l'air humide dans des conditions
définies. Le calcul du coefficient de diffusion de l'humidité dans l'épaisseur suppose un matériau fickien
monophasé ayant des propriétés constantes d'absorption d'humidité dans l'épaisseur de l'éprouvette. Ce
modèle est valable pour les matériaux homogènes et pour les composites renforcés à matrice polymère
soumis à essai au-dessous de leur température de transition vitreuse. Toutefois, certaines matrices à deux
phases, telles que les époxydes durcis, peuvent nécessiter un modèle d'absorption multiphase qui n'est pas
couvert par la présente Norme internationale.
1.2 Idéalement, la meilleure comparaison des propriétés d'absorption d'eau et/ou des coefficients de
diffusion des matériaux ne devrait être faite qu'en utilisant la teneur en humidité à l'équilibre de plastiques
exposés exactement aux mêmes conditions. La comparaison de matériaux utilisant la teneur en humidité à
l'équilibre ne suppose pas de comportement monophasé de diffusion fickien et n'y est donc pas limitée.
1.3 En variante, l'absorption d'eau d'éprouvettes de plastique ayant une géométrie définie et faisant l'objet
d'une immersion ou de mises en présence d'humidité dans des conditions définies, pendant un laps de temps
arbitraire, peut permettre de comparer différents lots du même matériau ou de servir d'essai de contrôle
qualité d'un matériau. Pour ces types de comparaisons, il est indispensable que toutes les éprouvettes aient
des dimensions identiques et soient, autant que possible, dans le même état physique (poli de surface,
tensions internes, etc.). Néanmoins, ces expositions ne provoquant pas une humidité d'équilibre, les résultats
de ce type d'essai ne peuvent pas être utilisés pour comparer les propriétés d'absorption d'eau de types de
plastiques différents. Il est recommandé de soumettre simultanément à essai les différents lots du même
matériau afin d'obtenir les résultats les plus fiables.
1.4 Les résultats obtenus en utilisant les méthodes spécifiées dans la présente Norme internationale
s'appliquent à la plupart des plastiques, à l'exception des plastiques alvéolaires, des granulés ou des poudres
qui peuvent avoir d'autres effets capillaires et d'absorption. Des expositions pendant un laps de temps fixe
permettent des comparaisons relatives des plastiques. Les essais décrits pour la détermination du coefficient
de diffusion peuvent ne pas être applicables à tous les plastiques. Les plastiques ne pouvant pas garder leur
forme lors de leur exposition à l'eau bouillante ne peuvent pas être comparés en utilisant la méthode 2
(voir 6.4).
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 175:1999, Plastiques — Méthodes d'essai pour la détermination des effets de l'immersion dans des
produits chimiques liquides
ISO 294-3, Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques —
Partie 3: Plaques de petites dimensions
ISO 2818, Plastiques — Préparation des éprouvettes par usinage
3 Principe
Les éprouvettes sont immergées dans de l'eau distillée à 23 °C ou dans de l'eau distillée bouillante, ou encore
exposées à des atmosphères à 50 % d'humidité relative, à des températures définies et pendant des laps de
temps spécifiés. La quantité d'eau absorbée par l'éprouvette est déterminée par mesurage de sa variation de
masse, c'est-à-dire la différence entre sa masse après exposition à l'eau et sa masse initiale, et elle est
exprimée en pourcentage de la masse initiale. Si besoin est, il est également possible de déterminer la
quantité d'eau perdue après séchage des éprouvettes.
Certaines applications peuvent nécessiter des atmosphères ayant une humidité relative comprise entre 70 %
et 90 % et une température située entre 70 °C et 90 °C. Il est possible d'utiliser des atmosphères ayant une
humidité relative et une température supérieures à celles recommandées dans la présente Norme
internationale, si ces conditions ont fait l'objet d'un accord entre les parties intéressées. Si des conditions
d'humidité relative et de température autres que celles recommandées sont utilisées, elles doivent faire l'objet
d'une description complète (avec les tolérances appropriées) dans le rapport d'essai.
4 Appareillage
4.1 Balance, précise à ± 0,1 mg (voir aussi 6.1.3).
4.2 Étuve, à ventilation forcée ou à vide, réglable à (50,0 ± 2,0) °C ou à toute autre température convenue
(voir aussi 6.1.2).
4.3 Récipients, contenant de l'eau distillée, ou de l'eau de pureté équivalente, équipés d'un dispositif de
chauffage
...
МЕЖДУНАРОДНЫЙ ISO
СТАНДАРТ 62
Третье издание
2008-02-15
Пластмассы. Определение поглощения
воды
Plastics – Determination of water absorption
Ответственность за подготовку русской версии несёт GOST R
(Российская Федерация) в соответствии со статьёй 18.1 Устава ISO
Ссылочный номер
©
ISO 2008
Отказ от ответственности при работе в PDF
Настоящий файл PDF может содержать интегрированные шрифты. В соответствии с условиями лицензирования, принятыми
фирмой Adobe, этот файл можно распечатать или смотреть на экране, но его нельзя изменить, пока не будет получена
лицензия на интегрированные шрифты и они не будут установлены на компьютере, на котором ведется редактирование. В
случае загрузки настоящего файла заинтересованные стороны принимают на себя ответственность за соблюдение
лицензионных условий фирмы Adobe. Центральный секретариат ISO не несет никакой ответственности в этом отношении.
Adobe - торговый знак фирмы Adobe Systems Incorporated.
Подробности, относящиеся к программным продуктам, использованные для создания настоящего файла PDF, можно найти в
рубрике General Info файла; параметры создания PDF были оптимизированы для печати. Были приняты во внимание все
меры предосторожности с тем, чтобы обеспечить пригодность настоящего файла для использования комитетами-членами
ISO. В редких случаях возникновения проблемы, связанной со сказанным выше, просьба проинформировать Центральный
секретариат по адресу, приведенному ниже.
ДОКУМЕНТ ОХРАНЯЕТСЯ АВТОРСКИМ ПРАВОМ
© ISO 2008
Все права сохраняются. Если не указано иное, никакую часть настоящей публикации нельзя копировать или использовать в
какой-либо форме или каким-либо электронным или механическим способом, включая фотокопии и микрофильмы, без
предварительного письменного согласия ISO, которое должно быть получено после запроса о разрешении, направленного по
адресу, приведенному ниже, или в комитет-член ISO в стране запрашивающей стороны.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 09 47
E-mail copyright @ iso.org
Web www.iso.org
Опубликовано в Швейцарии
ii © ISO 2008 – Все права сохраняются
Содержание Страница
Предисловие .iv
Введение .v
1 Область применения .1
2 Нормативные ссылки .1
3 Сущность метода.2
4 Аппаратура.2
5 Образцы для испытания.2
5.1 Общие положения .2
5.2 Образцы прямоугольной формы для гомогенных пластмасс .3
5.3 Образцы для испытания армированных пластмасс под действием анизотропной
диффузии.3
5.4 Образцы трубок .3
5.5 Образцы прутков.4
5.6 Образцы, отрезанные от готовых изделий, композиций для экструзии, листов или
многослойного материала.4
6 Условия испытания и проведение испытания.4
6.1 Общие положения .4
6.2 Обычные условия .5
6.3 Метод 1: Определение количества воды, поглощенной после погружения в воду при
температуре 23 °C.5
6.4 Метод 2: Определение количества воды, поглощенной после погружения в кипящую
воду.6
6.5 Метод 3: Определение растворимого в воде вещества, теряемого при погружении в
воду.6
6.6 Метод 4: Определение количества воды, поглощенной после воздействия
относительной влажности 50 % .6
7 Обработка результатов.7
7.1 Процент поглощенной воды по массе .7
7.2 Определение содержания воды при насыщении и коэффициента диффузии по
законам Фика.7
8 Прецизионность.9
9 Протокол испытания.9
Приложение A (информативное) Корреляция между водопоглощением испытуемых
образцов и законами диффузии Фика .10
Приложение B (информативное) Показатели прецизионности.12
Библиография.15
Предисловие
Международная организация по стандартизации (ISO) представляет собой всемирную федерацию,
состоящую из национальных органов по стандартизации (комитеты-члены ISO). Работа по разработке
международных стандартов обычно ведется Техническими комитетами ISO. Каждый комитет-член,
заинтересованный в теме, для решения которой образован данный технический комитет, имеет право
быть представленным в этом комитете. Международные организации, правительственные и
неправительственные, поддерживающие связь с ISO, также принимают участие в работе. ISO тесно
сотрудничает с Международной электротехнической комиссией (IEC) по всем вопросам
стандартизации в области электротехники.
Международные стандарты разрабатываются в соответствии с правилами, установленными в Части 2
Директив ISO/IEC.
Основное назначение технических комитетов заключается в разработке международных стандартов.
Проекты международных стандартов, принятые Техническими комитетами, направляются комитетам-
членам на голосование. Для их опубликования в качестве международных стандартов требуется
одобрение не менее 75 % комитетов-членов, участвовавших в голосовании.
Внимание обращается на тот факт, что отдельные элементы данного документы могут составлять
предмет патентных прав. ISO не несет ответственность за идентификацию каких–либо или всех
подобных патентных прав.
ISO 62 был подготовлен Техническим комитетом ISO/TC 61, Пластмассы, Подкомитетом SC 6,
Стойкость к старению, химическим и атмосферным воздействиям.
Настоящее третье издание отменяет и заменяет второе издание (ISO 62:1999), к которому был
добавлен раздел Прецизионность.
iv © ISO 2008 – Все права сохраняются
Введение
Пластмассы, подвергающиеся воздействию воды, демонстрируют три типа реакции:
a) изменения размеров (например, разбухание), вызванные поглощением воды;
b) экстракция растворимых в воде компонентов;
c) изменение других свойств.
Однако, только воздействие влажности, погружение и выдерживание в кипящей воде может привести к
различным реакциям материала. Равновесное содержание влаги можно использовать для сравнения
количества воды, поглощенной различными типами пластмасс под воздействием влаги. Содержание
влаги, определенное в неравновесных состояниях, можно использовать для сравнения разных партий
одного и того же материала и для определения коэффициента диффузии материала при определении
в тщательно контролируемых неравновесных условиях воздействия влаги и при использовании
образцов пластмассы определенных размеров.
МЕЖДУНАРОДНЫЙ СТАНДАРТ ISO 62:2008(R)
Пластмассы. Определение поглощения воды
1 Область применения
1.1 В данном международном стандарте описывается метод определения свойств влагопоглощения
в направлении «сквозь толщину» твердых пластмасс плоской или искривленной формы. Настоящий
международный стандарт также описывает методы определения количества воды, поглощенной
образцами пластмассы определенных размеров, при погружении в воду или под воздействием
влажного воздуха в контролируемых условиях. Коэффициент диффузии влаги “сквозь толщину” можно
определить для однофазного материала, предположив поведение образцов по закону диффузии Фика
с постоянными параметрами абсорбции по толщине образца. Такая модель действительна для
гомогенных материалов и для армированных композитов с пластмассовой матрицей, испытанных при
температуре ниже температуры стеклования. Однако некоторые двухфазные матрицы, такие как
отвержденные эпоксидные смолы, могут потребовать модели многофазной абсорбции, которая не
подпадает под данный международный стандарт.
1.2 В идеальном случае наилучшее сопоставление свойств поглощения воды и/или коэффициентов
диффузии материалов следует выполнять только, используя равновесное содержание влаги в
пластмассах, подвергаемых воздействию в идентичных состояниях. Сопоставление материалов,
используя свойства при влажном равновесии, не предполагает, и поэтому не ставит ограничения до
однофазной диффузии по закону Фика.
1.3 Альтернативно поглощение воды образцами пластмасс определенных размеров, погружаемых в
воду или подвергающихся влиянию влажности в контролируемых условиях, но в течение
произвольного периода времени, можно использовать для сравнения различных партий одного и того
же материала или для контроля качества данного материала. Для сравнения такого типа важно, чтобы
все испытуемые образцы были идентичных размеров и, имели максимально близкие физические
свойства, например, гладкость поверхности, внутренние напряжения, и т.д. Однако, влажное
равновесие в этих условиях не достигается. Поэтому результаты данного типа испытания нельзя
использовать для сравнения свойств влагопоглощения различных типов пластмасс. Для получения
более надежных результатов рекомендуется проводить испытания одновременно.
1.4 Результаты, полученные с использованием методов, описанных в данном международном
стандарте, применимы к большинству пластмасс на не применимы к ячеистым пластмассам,
гранулированным материалам или порошкам, которые могут продемонстрировать дополнительное
поглощение и капиллярные эффекты. Пластмассы, подвергаемые воздействию влаги в
контролируемых условиях в течение определенных периодов времени, обеспечивают относительные
аналогии между собой. Испытания, описанные для определения коэффициента диффузии, не могут
применяться ко всем пластмассам. Пластмассы, которые не держат форму при погружении в кипящую
воду, не рекомендуется сравнивать по методу 2 (см. 6.4).
2 Нормативные ссылки
Нижеследующие документы являются обязательными для применения данного документа. Для
датированных ссылок действительно только указанное издание. В случае недатированных ссылок
используется последняя редакция документа, на который дается ссылка (включая все изменения).
ISO 175:1999, Пластмассы. Методы определения эффектов от погружения в жидкие химические
соединения
ISO 294-3, Пластмассы. Формование под давлением образцов для испытания термореактивных
материалов. Часть3. Мелкие пластинки
ISO 2818, Пластмассы. Подготовка образцов для испытания с помощью механической обработки
3 Сущность метода
Образцы для испытания погружают в дистиллированную воду при температуре 23 °C или в кипящую
дистиллированную воду или выдерживают в атмосфере с относительной влажностью 50 % при
заданных температурах в течение установленных промежутков времени. Количество воды,
поглощенной каждым испытуемым образцом, определяют путем измерения изменения его массы, т.е.
разность между начальной массой и массой, измеренной после воздействия воды, изменение,
выраженное в процентах от начальной массы. Если требуется, количество воды, потерянной после
просушивания испытуемых образцов, также можно определить.
В некоторых задачах может потребоваться относительная влажность от 70 % до 90 % и температуры
от 70 °C до 90 °C. Относительная влажность и температуры выше рекомендованных данным
международным стандартом значений можно использовать по соглашению между заинтересованными
сторонами. Если используются условия относительной влажности и температуры отличаются от
рекомендованных, полное описание этих условий (с соответствующими допусками), необходимо
отразить это в протоколе испытания.
4 Аппаратура
4.1 Весы, точностью ± 0,1 мг (см. также 6.1.3).
4.2 Печь, с принудительной циркуляцией воздуха или вакуумная печь, поддерживаемая при
температуре (50,0 ± 2,0) °C или другой согласованной температуре (см. также 6.1.2).
4.3 Контейнеры, содержащие дистиллированную воду или воду эквивалентной чистоты,
оснащенные средствами
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.