EN 10051:2010

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen - Grenzabmaße und FormtoleranzenBandes laminées à chaud en continu, bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés - Tolérances sur les dimensions et la formeContinuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10051:2010SIST EN 10051:2012en,fr,de01-januar-2012SIST EN 10051:2012SLOVENSKI
STANDARDSIST EN 10051:19981DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10051
November 2010 ICS 77.140.50 Supersedes EN 10051:1991 + A1:1997English Version
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
Bandes laminées à chaud en continu, bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés - Tolérances sur les dimensions et la forme
Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen -Grenzabmaße und Formtoleranzen This European Standard was approved by CEN on 23 October 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10051:2010: ESIST EN 10051:2012

Standards with steel grades for this dimensional standard . 14Annex B (normative)
Options . 16 SIST EN 10051:2012

This European Standard does not apply to stainless steels and not to hot-rolled strip rolled in widths w < 600 mm (see EN 10048). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020, Definition and classification of grades of steel EN 10048, Hot-rolled narrow steel strip  Tolerances on dimensions and shape EN 10079, Definition of steel products 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 non-alloy and alloy steels
see EN 10020 3.2 wide strip and sheet/plate see EN 10079 3.3 crown difference in thickness between one of the edges and the centre of a rolled product SIST EN 10051:2012

1 200 mm, with trimmed edges (GK), nominal length 2 500 mm of steel 34Cr4 (1.7033) as specified in EN 10083-3: 20 sheets EN 10051 – 2,0 x 1 200GK x 2 500 steel EN 10083-3 – 34Cr4 EXAMPLE 2 5 t of strip according to this European Standard with nominal thickness of 4,5 mm, nominal width
1 500 mm, with mill edges of steel S235JR (1.0038), as specified in EN 10025-2: 5 t strip EN 10051 – 4,5 x 1 500 steel EN 10025-2 – S235JR 5 Form of supply 5.1 Sheet/plate and strip shall be supplied with mill edges or with trimmed edges (GK), as agreed at the time of enquiry and order (see Annex B, option a)). In the absence of information on the form of supply, sheet/plate and strip shall be supplied with mill edges. 5.2 The possibility of delivering coils with welding seams can be agreed at the time of enquiry and order. The indication of the location of the weld can be agreed at the same time (see Annex B, option b)). 5.3 Where no specific choice is made by the purchaser concerning points g), h), and i) of 4.1 is given by the purchaser, the supplier shall refer back to the purchaser. SIST EN 10051:2012

≤ 3,00 ±0,15 ±0,17 ±0,18 ±0,20 3,00 < t
≤ 4,00 ±0,17 ±0,18 ±0,20 ±0,20 4,00 < t ≤ 5,00 ±0,18 ±0,20 ±0,21 ±0,22 5,00 < t ≤ 6,00 ±0,20 ±0,21 ±0,22 ±0,23 6,00 < t ≤ 8,00 ±0,22 ±0,23 ±0,23 ±0,26 8,00 < t ≤ 11,00 ±0,24 ±0,25 ±0,25 ±0,28
6.1.2 The tolerances on thickness for steels, not covered by 6.1.1, are given in Tables 3 to 6. These tolerances are indicated as categories A, B, C, D. The dimensional tolerances of steel grades which do not have a specified minimum yield strength are the ones of category D. Table 3 — Tolerances on thickness for strip and sheet/plate of steels with a specified minimum yield strength Re ≤ 300 MPa (category A) Dimensions in mm Nominal thickness t Tolerances for a nominal width w w ≤ 1 200 1 200 < w ≤ 1 500 1 500 < w ≤ 1 800 w > 1 800 t ≤ 2,00 ±0,17 ±0,19 ±0,21 – 2,00 < t ≤ 2,50 ±0,18 ±0,21 ±0,23 ±0,25 2,50 < t ≤ 3,00 ±0,20 ±0,22 ±0,24 ±0,26 3,00 < t ≤ 4,00 ±0,22 ±0,24 ±0,26 ±0,27 4,00 < t ≤ 5,00 ±0,24 ±0,26 ±0,28 ±0,29 5,00 < t ≤ 6,00 ±0,26 ±0,28 ±0,29 ±0,31
...