EN 10207:2017

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stähle für einfache Druckbehälter - Technische Lieferbedingungen für Blech, Band und StabstahlAciers pour appareils à pression simples - Conditions techniques de livraison des tôles, bandes et barresSteels for simple pressure vessels - Technical delivery requirements for plates, strips and bars77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposes23.020.32Pressure vesselsICS:Ta slovenski standard je istoveten z:EN 10207:2017SIST EN 10207:2018en01-februar-2018SIST EN 10207:2018SLOVENSKI
STANDARDSIST EN 10207:20051DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10207
November
t r s y ICS
y yä s v rä u r Supersedes EN
s r t r yã t r r wEnglish Version
Steels for simple pressure vessels æ Technical delivery requirements for platesá strips and bars Aciers pour appareils à pression simples æ Conditions techniques de livraison des tôlesá bandes et barres
Stähle für einfache Druckbehälter æ Technische Lieferbedingungen für Blechá Band und Stabstahl This European Standard was approved by CEN on
t z August
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r t r yã t r s y ESIST EN 10207:2018

European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Classification and designation . 5 4.1 Classification . 5 4.2 Designation. 5 5 Information to be supplied by the purchaser . 6 5.1 Mandatory information . 6 5.2 Options . 6 6 Manufacturing process . 6 6.1 Steelmaking . 6 6.2 Delivery condition . 6 7 Requirements . 7 7.1 General . 7 7.2 Chemical composition . 7 7.3 Mechanical properties . 8 7.4 Surface condition . 10 7.5 Internal soundness . 10 7.6 Dimensions and tolerances on dimensions . 10 7.7 Calculation of mass . 12 8 Inspection . 12 8.1 Types of inspection and inspection documents . 12 8.2 Tests to be carried out for specific inspection . 12 9 Sampling and preparation of samples and test pieces . 13 9.1 Test units for specific inspection . 13 9.2 Preparation of samples and test pieces . 13 9.3 Preparation of test pieces . 15 10 Test methods . 16 10.1 Chemical analysis . 16 10.2 Tensile test at room temperature . 16 10.3 Impact test . 16 10.4 Tensile test at elevated temperature . 17 10.5 Visual examination . 17 10.6 Ultrasonic test . 17 10.7 Retests, sorting and reprocessing . 17 11 Marking . 17 Annex A (informative)
Definition of “simple pressure vessel” . 18 Annex B (informative)
Changes to the previous version EN 10207:2005 . 19 Annex ZA (informative)
Relationship between this document and the Essential Requirements of the Directive for Simple Pressure Vessels 2014/29/EU aimed to be covered. 20 Bibliography . 21 SIST EN 10207:2018

« s r ¹C for nominal thicknesses
w mm < t or b < 6mm (only flat products or rectangular bars). 5.2 Options A number of options are specified in this document and listed below. In the event that the purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, the products shall be supplied in accordance with the basic specification (see 5.1): 1) steelmaking process (see 6.1.1); 2) internal soundness (see 7.5); 3) additional tests (see 8.2.2); 4) circular test pieces for the tensile test (see Table 6, footnote b); 5) test temperature for tensile test at elevated temperature (see 10.4). 6 Manufacturing process 6.1 Steelmaking 6.1.1 Unless a special steelmaking process has been agreed at the time of enquiry and order, the steelmaking process for steels in accordance with this document shall be at the discretion of the manufacturer. 6.1.2 The steels shall be fully killed and not susceptible to ageing. NOTE For these steels covered in Table 1, requirements of the Directive 2014/29/EU were taken into account by the specification of a minimum total aluminium content of 0,020 %. 6.2 Delivery condition The products shall be delivered in the normalized or in an equivalent condition obtained by normalizing rolling (see 3.1). SIST EN 10207:2018

apply. If such nitrogen binding elements were added to the steel their content shall be given in the inspection
document. SIST EN 10207:2018
...