EN 14783:2006

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Vollflächig unterstützte Dachdeckungs- und Wandbekleidungselemente für die Innen- und Außenanwendung aus Metallblech - Produktspezifikation und AnforderungenTôles et bandes métalliques totalement supportées pour couverture, bardages extérieur et intérieur - Spécification de produit et exigencesFully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements91.060.20StreheRoofs91.060.10Stene. Predelne stene. FasadeWalls. Partitions. Facades77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 14783:2006SIST EN 14783:2006en01-december-2006SIST EN 14783:2006SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14783September 2006ICS 77.140.50; 77.150.01; 91.060.10; 91.060.20 English VersionFully supported metal sheet and strip for roofing, externalcladding and internal lining - Product specification andrequirementsTôles et bandes métalliques totalement supportées pourcouverture, bardages extérieur et intérieur - Spécificationde produit et exigencesVollflächig unterstützte Dachdeckungs- undWandbekleidungselemente für die Innen- undAußenanwendung aus Metallblech - Produktspezifikationund AnforderungenThis European Standard was approved by CEN on 6 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14783:2006: ESIST EN 14783:2006

Multilayer coated steel sheet.15 A.1 General.15 A.2 Substrate material.15 A.3 Specific requirements.15 A.3.1 Minimum nominal values of thickness.15 A.3.2 Bituminous coating specification.16 A.3.3 Durability.16 A.4 Freedom from defects.16 Annex B (normative)
Test conditions for the reaction to fire tests.17 B.1 General.17 B.2 Mounting and fixing conditions of test specimens in the SBI test.17 B.2.1 General.17 SIST EN 14783:2006

Clauses of this European Standard addressing the provisions of EU Construction Products Directive.20 ZA.1 Scope and relevant characteristics.20 ZA.2 Procedure(s) for the attestation of conformity of products.22 ZA.2.1 Systems of attestation of conformity.22 ZA.2.2 Declaration of conformity.23 ZA.3 CE marking and labelling.24 Bibliography.27
4.3 Water permeability As long as the products covered by this European Standard have no holes (as defects), they are water impermeable. Where required, the absence of holes shall be checked by visual inspection of the finished product. 4.4 Dimensional change The thermal expansion shall be taken into account in the change of dimensions of the product, where this change may have an effect on the performance of the product, by stating the appropriate thermal expansion coefficient. In the absence of experimental data the following thermal expansion coefficient shall be used:  aluminium: 24 x 10–6 K–1,  copper: 16,8 x 10–6 K–1,  lead: 29,3 x 10–6 K–1,  stainless steel: 10,0 x 10–6 K–1 to 17,0 x 10–6 K–1, depending on the grade, according to EN 10088-1,  steel: 12 x 10–6 K–1,  zinc: 22 x 10–6 K–1, unless the manufacturer demonstrates by appropriate means that more accurate values are applicable. 4.5 Dimensional tolerances The dimensional tolerances specified for roof covering products in the applicable standard from the following: EN 501, EN 502, EN 504, EN 505, EN 507 and EN 12588, shall not be exceeded. For other products, the tolerances declared shall be appropriate, due account being taken of any national provisions of the country of use. SIST EN 14783:2006

PCS ≤ 4,0 MJ/m2 or a mass ≤ 200 g/m2. NOTE Individual Member States may have "deemed to satisfy" lists which go beyond the list given in the Commission Decision 2000/553/EC. 5.1.2 Products classified without the need for further testing The following products are considered to be classified in classes B ROOF(t1), B ROOF(t2), B ROOF(t3) and B ROOF(t4) without further testing in accordance with Commission Decision 2005/403/EC: profiled steel sheets, flat steel sheets or panels of coil coated galvanised or zinc-aluminium alloy coated steel of metal thickness ≥ 0,40 mm SIST EN 14783:2006

Table 3 have not been declared for the base material in accordance with Table 2 or are changed during the production process, the manufacturer claiming compliance with this European Standard shall assess and declare the characteristics of Table 3 that have not been declared. The base material may be presumed to have the performances stated of them by their supplier, although this does not replace the responsibility on the roofing, cladding or lining product manufacturer to ensure that only a base material having the correct values of characteristics to allow the finished roofing, cladding or lining product to meet the requirements of this European Standard is used. All characteristics in Clause 4 shall be subject to initial type testing, with the following exceptions:  external fire performance when using the CWFT option, in accordance with 5.1.2 or when deemed to satisfy in accordance with 5.1.1 (although measurement may be required to ensure that the product meets the definition required for CWFT and deemed to satisfy);  reaction to fire when deemed to satisfy Class A1, in accordance with 5.2.1;  release of dangerous substances that may be assessed indirectly by controlling the content of the substance concerned. Whenever a change occurs in the base material, the finished product or the production process (subject to the definition of a family), which could change significantly one or more of the characteristics, the type tests shall be repeated for the appropriate characteristic(s). The results of the initial type testing shall be recorded and held by the manufacturer for at least 10 years after the end of production of the product to which they apply. SIST EN 14783:2006
...