EN 13244-1:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.6SORãQRKunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 1: AllgemeinesSystemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 1: GénéralitésPlastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN 13244-1:2002SIST EN 13244-1:2003en01-oktober-2003SIST EN 13244-1:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13244-1December 2002ICS 93.030English versionPlastics piping systems for buried and above-ground pressuresystems for water for general purposes, drainage and sewerage- Polyethylene (PE) - Part 1: GeneralSystèmes de canalisations en plastique pour lesapplications générales de transport d'eau, de branchementet de collecteurs d'assainissement, enterrés sous pression- Polyéthylène (PE) - Partie 1: GénéralitésKunstoff-Rohrleitungssysteme für erd- und oberirdischverlegte Druckrohrleitungen für Brauchwasser,Entwässerung und Abwasser - Polyethylen (PE) - Teil 1:AllgemeinesThis European Standard was approved by CEN on 14 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13244-1:2002 ESIST EN 13244-1:2003

Pressure reduction coefficients.15Bibliography.16SIST EN 13244-1:2003

Plastics piping and ducting systems — Polyolefin pipes and fittings — Determination of oxidationinduction time.EN 1056,
Plastics piping and ducting systems – Plastics pipes and fittings – Method for exposure to direct (natural)weathering.EN 12099,
Plastics piping systems — Polyethylene piping materials and components — Determination of volatilecontent.EN 12107,
Plastics piping systems — Injection-moulded thermoplastics fittings, valves and ancillary equipment —Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of pipingcomponents.
1)1 bar = 105 N/m2.SIST EN 13244-1:2003

Plastics piping systems — Determination of moisture content in thermoplastics by coulometry.EN 13244-2,
Plastics piping systems for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage — Polyethylene (PE) – Part 2: Pipes.EN ISO 1133:1999,
Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate(MVR) of thermoplastics (ISO 1133:1997).EN ISO 12162:1995,
Thermoplastics materials for pipes and fittings for pressure applications — Classification anddesignation — Overall service (design) coefficient (ISO 12162:1995).EN ISO 13478:1997, Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapidcrack propagation (RCP) — Full-scale test (FST) (ISO 13478:1997).EN ISO 13479:1997,
Polyolefine pipes for the conveyance of fluids — Determination of resistance to crackpropagation — Test method for slow crack growth on notched pipes (notch test) (ISO 13479:1997).ISO 3:1973,
Preferred numbers — Series of preferred numbers.ISO 472:1988,
Plastics — Vocabulary.ISO 760:1998,
Determination of water – Karl Fischer method (General method).ISO 1043-1:1997,
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their specialcharacteristics.ISO 1183:1987,
Plastics — Methods for determining the density and relative density of non-cellular plastics.ISO 6964:1986,
Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis— Test method and basic specification.ISO/TR 9080:1992,
Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostaticstress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials.ISO 11414:1996,
Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test pieceassemblies by butt fusion.ISO 13477:1997,
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crackpropagation (RCP) — Small-scale steady-state test (S4 test).ISO 13953:2001,
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode oftest pieces from a butt-fused joint.ISO 18553:2002, Method for the assessment of the degree of pigment or carbon black dispersion in polyolefinpipes, fittings and compounds.3 Definitions, symbols and abbreviations3.1 Terms and definitionsFor the purposes of this European Standard, the terms and definitions in ISO 3:1973, ISO 472:1988 andISO 1043-1:1997 together with the following apply.NOTE The symbols de, e, emin and emax in EN 13244 are equivalent to dey, ey, ey,min and ey,max respectively inISO 11922-1[1].SIST EN 13244-1:2003
...