General Information

Abstract

This document specifies the interface geometry between valves and pump adapters as well as flow rate performance, pressure, marking and labelling for air pumps for inflatable consumer articles (see definition in 3.1).
This document does not apply to:
- valves of personal flotation devices according to EN ISO 12402;
- diving accessories and buoyancy compensators according to EN 1809.
This document excludes the following valve types:
- valves used for bicycles and vehicles;
- needle valves (e. g. valves used for team sport balls).

Status
Published
Publication Date
10-Jan-2012
Withdrawal Date
30-Jul-2012
ICS
23.080 - Pumps
Technical Committee
CEN/TC 136 - Sports, playground and other recreational equipment
Drafting Committee
CEN/TC 136/WG 13 - Floating leisure articles for use on water
Current Stage
9093 - Decision to confirm - Review Enquiry
Start Date
30-Nov-2023
Completion Date
23-Sep-2026
Ref Project
SIST EN 16051-1:2012 - Inflation devices and accessories for inflatable consumer products - Part 1: Compatibility of valves and valve adapters

Buy Documents

Overview

EN 16051-1:2012 is a CEN standard that defines the mechanical and performance compatibility between valves and pump adapters for inflatable consumer products. It specifies valve interface geometry, pressure classing, strength and retention requirements, marking/label needs and basic flow/compatibility considerations to ensure efficient, safe inflation of leisure inflatables (air beds, pool toys, small boats, air furniture, etc.). The standard excludes personal flotation device valves (EN ISO 12402), diving/buoyancy equipment (EN 1809), bicycle/vehicle valves and needle valves (sport balls).

Key Topics

  • Interface geometry - Dimensional locations where pump adapters and valves connect are defined so adapters and hoses mate reliably. Typical sizes for screw and plug valves are given (examples: screw valve di - X‑Large 46.8 mm, Large 31.0 mm, Medium 24.0 mm, Small 17.5 mm).
  • Valve types covered - Screw valves (with/without twist‑lock), plug valves (sinkable and non‑sinkable), valves with non‑return devices and corresponding adapter interfaces.
  • Pressure classes - Valves are classified by nominal operating pressure:
    • Class A: 0.3 bar < P ≤ 0.8 bar
    • Class B: 0.06 bar ≤ P ≤ 0.3 bar
    • Class C: P < 0.06 bar
  • Retention and strength requirements - Components must remain attached when opened; securing devices are tested at 10 N, 40 °C for 10 minutes. The valve–adapter connection must not disengage at 1.2 × nominal pressure.
  • Testing conditions - Unless specified otherwise, tests are performed at room temperature. EN 16051-1 references test methods and adapters described in EN 16051-2.
  • Marking and labelling - Requirements are included to ensure correct use and to aid compatibility between pumps and products (details are specified in the standard).

Applications

  • Designing valves, pump adapters and inflation fittings for consumer inflatables.
  • Specifying interface dimensions and pressure classes in product technical documentation.
  • Verifying product compatibility and safety during product development and QA testing.
  • Ensuring market compliance and facilitating interoperability between pumps and inflatables sold separately.
  • Guiding retailers, OEMs and accessory manufacturers to reduce user frustration and safety risks from incompatible pumps/adapters.

Who should use this standard

  • Manufacturers of inflatable consumer articles and pump/adapter suppliers
  • Product designers and mechanical engineers working on inflatables
  • Test laboratories and conformity assessment bodies
  • Compliance officers and quality assurance teams
  • Retailers and aftermarket accessory producers focused on compatibility

Related standards

  • EN 16051-2 - Safety requirements, durability, performance, compatibility and test methods of inflators (companion standard)
  • EN ISO 12402, EN 1809 - referenced as out of scope for this part (personal flotation and diving equipment)

Keywords: EN 16051-1:2012, inflation devices, valve compatibility, pump adapters, inflatable consumer products, valve interface geometry, pressure classes, CEN standard.

Relations

Refers
EN 16051-2:2012 - Inflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators
Effective Date
28-Jan-2026
Referred By
EN IEC 61400-6:2020 - Wind energy generation systems - Part 6: Tower and foundation design requirements
Effective Date
09-Feb-2026
Referred By
EN ISO 19903:2006 - Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)
Effective Date
28-Jan-2026
Referred By
EN ISO 11296-9:2022 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
Effective Date
28-Jan-2026
Referred By
EN 15649-1:2009+A1:2012 - Floating leisure articles for use on and in the water - Part 1: Classification, materials, general requirements and test methods
Effective Date
28-Jan-2026
Referred By
EN 15649-1:2009+A2:2013 - Floating leisure articles for use on and in the water - Part 1: Classification, materials, general requirements and test methods
Effective Date
28-Jan-2026
Referred By
EN ISO 25649-1:2024 - Floating leisure articles for use on and in the water - Part 1: Classification, materials, general requirements and test methods (ISO 25649-1:2024)
Effective Date
28-Jan-2026
Referred By
EN ISO 25649-1:2017 - Floating leisure articles for use on and in the water - Part 1: Classification, materials, general requirements and test methods (ISO 25649-1:2017)
Effective Date
28-Jan-2026

Buy Documents

Get Certified

Connect with accredited certification bodies for this standard

Institut za varilstvo d.o.o. (Welding Institute)

Slovenia's leading welding institute since 1952. ISO 3834, EN 1090, pressure equipment certification, NDT personnel, welder qualification. Only IIW Au

SA Slovenia Verified
Visit Website

Sponsored listings

Frequently Asked Questions

EN 16051-1:2012 is a standard published by the European Committee for Standardization (CEN). Its full title is "Inflation devices and accessories for inflatable consumer products - Part 1: Compatibility of valves and valve adapters". This standard covers: This document specifies the interface geometry between valves and pump adapters as well as flow rate performance, pressure, marking and labelling for air pumps for inflatable consumer articles (see definition in 3.1). This document does not apply to: - valves of personal flotation devices according to EN ISO 12402; - diving accessories and buoyancy compensators according to EN 1809. This document excludes the following valve types: - valves used for bicycles and vehicles; - needle valves (e. g. valves used for team sport balls).

This document specifies the interface geometry between valves and pump adapters as well as flow rate performance, pressure, marking and labelling for air pumps for inflatable consumer articles (see definition in 3.1). This document does not apply to: - valves of personal flotation devices according to EN ISO 12402; - diving accessories and buoyancy compensators according to EN 1809. This document excludes the following valve types: - valves used for bicycles and vehicles; - needle valves (e. g. valves used for team sport balls).

EN 16051-1:2012 is classified under the following ICS (International Classification for Standards) categories: 23.080 - Pumps. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 16051-1:2012 has the following relationships with other standards: It is inter standard links to EN 16051-2:2012, EN IEC 61400-6:2020, EN ISO 19903:2006, EN ISO 11296-9:2022, EN 15649-1:2009+A1:2012, EN 15649-1:2009+A2:2013, EN ISO 25649-1:2024, EN ISO 25649-1:2017. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 16051-1:2012 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pumpen und Pumpenzubehör für aufblasbare Verbraucherartikel - Teil 1: Kompatibilität von Ventilen und VentiladapternPompes et accessoires pour des produits gonflables destinés aux consommateurs - Partie 1: Compatibilité des valves et des adaptateursInflation devices and accessories for inflatable consumer products - Part 1: Compatibility of valves and valve adapters97.220.01Sports equipment and facilities in generalICS:Ta slovenski standard je istoveten z:EN 16051-1:2012SIST EN 16051-1:2012en,fr,de01-marec-2012SIST EN 16051-1:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16051-1
January 2012 ICS 23.080 English Version
Inflation devices and accessories for inflatable consumer products - Part 1: Compatibility of valves and valve adapters
Dispositifs et accessoires de gonflage pour biens de consommation gonflables - Partie 1: Compatibilité des valves et adaptateurs de valves
Pumpen und Pumpenzubehör für aufblasbare Verbraucherartikel - Teil 1: Kompatibilität von Ventilen und Ventiladaptern This European Standard was approved by CEN on 29 October 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16051-1:2012: ESIST EN 16051-1:2012

This part of the standard, Part 1, addresses the requirements for valves and where necessary, adaptors to ensure good fit and mechanical efficiency when inflating the device. 1 Scope This document specifies the valve side interface geometry between valves and pump adapters as well as strength requirements of valves and valve adapters for inflatable consumer articles (see definition in 3.1). This document does not apply for
 valves of personal flotation devices according to EN ISO 12402;  diving accessories and buoyancy compensators according to EN 1809.
This document excludes the following valve types:  valves used for bicycles and vehicles;  needle valves (e. g. valves used for team sport balls). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16051-2, Inf
...