EN 13244-5:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 5: Gebrauchstauglichkeit des SystemsSystemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 5: Aptitude a l'emploi du systemePlastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN 13244-5:2002SIST EN 13244-5:2003en01-oktober-2003SIST EN 13244-5:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13244-5December 2002ICS 93.030English versionPlastics piping systems for buried and above-ground pressuresystems for water for general purposes, drainage and sewerage- Polyethylene (PE) - Part 5: Fitness for purpose of the systemSystèmes de canalisations en plastique pour lesapplications générales de transport d'eau, de branchementet de collecteurs d'assainissement, enterrés sous pression- Polyéthylène (PE) - Partie 5: Aptitude à l'emploi dusystèmeKunstoff-Rohrleitungssysteme für erd- und oberirdischverlegte Druckrohrleitungen für Brauchwasser,Entwässerung und Abwasser - Polyethylen (PE) - Teil 5:Gebrauchstauglichkeit des SystemsThis European Standard was approved by CEN on 16 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13244-5:2002 ESIST EN 13244-5:2003

Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforcedthermosetting (GRP) plastics based on polyester resin (UP).EN 1456,
Plastics piping systems for buried and above-ground drainage and sewerage under pressure —Unplasticized poly(vinyl chloride) (PVC-U).According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13244-5:2003

Thermoplastics piping systems — End-load-bearing mechanical joints between pressure pipes andfittings — Test method for resistance to pull-out under constant longitudinal force.EN 713,
Plastics piping systems — Mechanical joints between fittings and polyolefin pressure pipes — Testmethod for leaktightness under internal pressure of assemblies subjected to bending.EN 715,
Thermoplastics piping systems — End-load-bearing joints between small diameter pressure pipes andfittings — Test method for leaktightness under internal water pressure, including end thrust.EN 911,
Plastics piping systems — Elastomeric sealing ring type joints and mechanical joints for thermoplasticspressure piping — Test method for leaktightness under external hydrostatic pressure.
1)1 bar = 105 N/m2.SIST EN 13244-5:2003

Plastics piping systems — Thermoplastics pipes — Determination of resistance to internal pressureat constant temperature.EN 13244-1:2002,
Plastics piping systems for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage — Polyethylene (PE) — Part 1: General.ISO 11413:1996,
Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE)pipe and an electrofusion fitting.ISO 11414:1996,
Plastics pipes and fittings — Preparation of polyeth
...