oSIST prEN IEC 60335-2-6:2026

SLOVENSKI STANDARD
01-januar-2026
Gospodinjski in podobni električni aparati - Varnost - 2-6. del: Posebne zahteve za
nepremične štedilnike, kuhalnike, pečice in podobne aparate
Household and similar electrical appliances - Safety - Part 2-6: Particular requirements
for stationary cooking ranges, hobs, ovens and similar appliances
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-6:
Besondere Anforderungen für ortsfeste Herde, Kochmulden, Backöfen und ähnliche
Geräte
Appareils électrodomestiques et analogues - Sécurité - Partie 2-6: Exigences
particulières pour les cuisinières, les tables de cuisson, les fours et les appareils fixes
analogues
Ta slovenski standard je istoveten z: prEN IEC 60335-2-6:2025
ICS:
13.120 Varnost na domu Domestic safety
97.040.20 Štedilniki, delovni pulti, Cooking ranges, working
pečice in podobni aparati tables, ovens and similar
appliances
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
prEN IEC 60335-2-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2025
ICS 13.120; 97.040.20 Will supersede EN 60335-2-6:2015; EN 60335-2-
6:2015/A1:2020; EN 60335-2-6:2015/A11:2020
English Version
Household and similar electrical appliances - Safety - Part 2-6:
Particular requirements for stationary cooking ranges, hobs,
ovens and similar appliances
(IEC 60335-2-6:2024)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-6: Exigences particulières pour les cuisinières, les ähnliche Zwecke - Teil 2-6: Besondere Anforderungen für
tables de cuisson, les fours et les appareils fixes analogues ortsfeste Herde, Kochmulden, Backöfen und ähnliche
(IEC 60335-2-6:2024) Geräte
(IEC 60335-2-6:2024)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2026-02-13.

The text of this draft consists of the text of IEC 60335-2-6:2024.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 80663 Ref. No. prEN IEC 60335-2-6:2025 E

1 European foreword
2 This document (prEN IEC 60335-2-6:2025) consists of the text of IEC 60335-2-6:2024 prepared by
3 IEC/TC 61 "Safety of household and similar electrical appliances".
4 This document is currently submitted to the Enquiry.
5 The following dates are proposed:
• latest date by which the existence of this document (doa) dav + 6 months
has to be announced at national level
• latest date by which this document has to be (dop) dav + 12 months
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) dav + 36 months
conflicting with this document have to be withdrawn (to be confirmed or
modified when voting)
6 This document will supersede EN 60335-2-6:2015 and all of its amendments and corrigenda (if any).
7 This document is read in conjunction with prEN IEC 60335-2-6:2025/prAA:2025.
8 This document has been prepared under a standardisation request addressed to CENELEC by the
9 European Commission. The Standing Committee of the EFTA States subsequently approves these
10 requests for its Member States.
11 For relationship with EU legislation, see informative Annexes ZZA and ZZC, which are an integral part
12 of prEN IEC 60335-2-6:2025/prAA:2025.
Sensitivity: Internal / Non-Personal Data

IEC 60335-2-6 ®
Edition 7.0 2024-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Household and similar electrical appliances – Safety –

Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens

and similar appliances
Appareils électrodomestiques et analogues – Sécurité –

Partie 2-6: Exigences particulières pour les cuisinières, les tables de cuisson,

les fours et les appareils fixes analogues

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.120, 97.040.20 ISBN 978-2-8322-9460-4

– 2 – IEC 60335-2-6:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 9
4 General requirement . 15
5 General conditions for the tests . 15
6 Classification . 15
7 Marking and instructions . 16
8 Protection against access to live parts . 20
9 Starting of motor-operated appliances . 20
10 Power input and current . 20
11 Heating . 21
12 Charging of metal-ion batteries . 26
13 Leakage current and electric strength at operating temperature . 26
14 Transient overvoltages . 27
15 Moisture resistance . 27
16 Leakage current and electric strength . 29
17 Overload protection of transformers and associated circuits . 30
18 Endurance . 30
19 Abnormal operation . 30
20 Stability and mechanical hazards . 32
21 Mechanical strength . 33
22 Construction . 35
23 Internal wiring . 45
24 Components . 45
25 Supply connection and external flexible cords . 46
26 Terminals for external conductors . 46
27 Provision for earthing . 46
28 Screws and connections . 46
29 Clearances, creepage distances and solid insulation . 46
30 Resistance to heat and fire . 47
31 Resistance to rusting . 47
32 Radiation, toxicity and similar hazards . 47
Annexes . 55
Annex B (normative) Battery-operated appliances, separable batteries and detachable
batteries for battery-operated appliances . 55
Annex R (normative) Software evaluation . 56
Annex AA (informative) Guidance for the application of remote operation for induction
hobs . 57
Bibliography . 58
Index of defined terms . 59

IEC 60335-2-6:2024 © IEC 2024 – 3 –

Figure 101 – Vessel for testing hob elements . 48
Figure 102 – Vessel for testing induction hob elements . 49
Figure 103 – Load for testing rotating spits . 50
Figure 104 – Probe for measuring surface temperatures . 51
Figure 105 – Arrangement of work surface for spillage test on built-in ovens . 51
Figure 106 – Detail of bottle cap and position of hole . 52
Figure 107 – Spillage solution bottle . 52
Figure 108 – Bottle position for the spillage test . 53
Figure 109 – Probe for measuring temperatures inside empty vessels . 53
Figure 110 – Indication for decentring vessels . 54
Figure AA.1 – Guidance for the application of remote operation for induction hobs . 57

Table 101 – Quantity of liquid in the vessel . 11
Table 102 – Maximum temperature rises for specified external accessible surfaces
under normal operating conditions . 25
Table 103 (Australia and New Zealand) – Maximum temperature rises for specified

external accessible surfaces under normal operating conditions . 26
Table 104 – Test loads . 34

– 4 – IEC 60335-2-6:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-6: Particular requirements for stationary cooking ranges,
hobs, ovens and similar appliances

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60335-2-6 has been prepared by IEC technical committee 61: Safety of household and
similar electrical appliances. It is an International Standard.
This seventh edition cancels and replaces the sixth edition published in 2014 and
Amendment 1:2018. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) alignment with IEC 60335-1:2020;
b) deletion of notes (15.2) and conversion of notes to normative text (Clause 1, 3.1.9.101,
7.103, 11.7, 15.2, 16.2, 22.109, 22.120, 22.132, 22.124, Figure 103);

IEC 60335-2-6:2024 © IEC 2024 – 5 –
c) application of test probe 19 (8.1.1, 20.2);
d) alignment of limits on the temperature rise of external accessible surfaces (Clause 11);
e) addition of requirements for automatic regulation systems and remote automatic regulation
systems for induction hobs (3.7.103, 3.11.4, 3.11.5, 3.11.101, 7.12, 19.102, 22.40, 22.62,
Annex AA);
f) addition of requirements for remote operation of ovens (22.51).
The text of this International Standard is based on the following documents:
Draft Report on voting
61/7253/FDIS 61/7275/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts of the IEC 60335 series, under the general title: Household and similar
electrical appliances – Safety, can be found on the IEC website.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments unless that edition precludes it; in that case, the latest edition that does not
preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
NOTE 1 When "Part 1" is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to convert
that publication into the IEC standard: Particular requirements for stationary cooking ranges,
hobs, ovens and similar appliances.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as
far as is reasonable. When this standard states "addition", "modification" or "replacement", the
relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.

– 6 – IEC 60335-2-6:2024 © IEC 2024
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations can need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally
not earlier than 12 months or later than 36 months from the date of publication.
The following differences exist in the countries indicated below.
– 11.101: Table 103 is applicable for limits on surface temperatures (Australia, New Zealand).
– 24.101: Socket-outlets have to be provided with residual current devices which may be
combined with the overcurrent protective device (Australia).
– 25.3: Cooking ranges that are not built-in shall not be permanently connected to the fixed
wiring (New Zealand).
IMPORTANT – The "colour inside" logo on the cover page of this document indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

IEC 60335-2-6:2024 © IEC 2024 – 7 –
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
Guidance documents concerning the application of the safety requirements for appliances can
be accessed via TC 61 supporting documents on the IEC website
https://www.iec.ch/tc61/supportingdocuments
This information is given for the convenience of users of this International Standard and does
not constitute a replacement for the normative text in this standard.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in normal
use taking into account the manufacturer's instructions. It also covers abnormal situations that
can be expected in practice and takes into account the way in which electromagnetic
phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that there
is compatibility with the wiring rules when the appliance is connected to the supply mains.
However, national wiring rules can differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with in
Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal publications, basic safety publications and group safety publications covering a hazard are not
applicable since they have been taken into consideration when developing the general and particular requirements
for the IEC 60335 series of standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of the
requirements and, if found to be substantially equivalent, may be considered to comply with the
standard.
NOTE 3 Standards dealing with non-safety aspects of household appliances are:
– IEC standards published by TC 59 concerning methods of measuring performance;
– CISPR 11, CISPR 14-1 and relevant IEC 61000-3 series standards concerning electromagnetic emissions;
– CISPR 14-2 concerning electromagnetic immunity;
– IEC standards published by TC 111 concerning environmental matters.

– 8 – IEC 60335-2-6:2024 © IEC 2024
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-6: Particular requirements for stationary cooking ranges,
hobs, ovens and similar appliances

1 Scope
This clause of Part 1 is replaced by the following.
This Part of IEC 60335 deals with the safety of stationary electric cooking appliances, such
as cooking ranges, hobs, and ovens, for household use, their rated voltage being not more
than 250 V for single-phase appliances connected between one phase and neutral, and 480 V
for other appliances including direct current (DC) supplied appliances and battery-operated
appliances.
This standard also includes some requirements for ovens that are intended to be used on board
ships.
Examples of appliances that are within the scope of this standard are:
– griddles;
– grills;
– induction hobs;
– induction wok elements;
– pyrolytic self-cleaning ovens;
– steam ovens.
As far as is practicable, this standard deals with the common hazards presented by appliances
that are encountered by all persons in and around the home. However, in general, it does not
take into account:
– persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
Attention is drawn to the fact that:
– for appliances intended to be used in vehicles or on board ships or aircraft, additional
requirements can be necessary;
– in many countries, additional requirements are specified by the national health authorities,
the national authorities responsible for the protection of labour, the national water supply
authorities and similar authorities.

IEC 60335-2-6:2024 © IEC 2024 – 9 –
This standard does not apply to:
– appliances intended for commercial catering;
– appliances intended to be used in locations where special conditions prevail, such as the
presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– grills, toasters and similar portable cooking appliances (IEC 60335-2-9);
– microwave ovens (IEC 60335-2-25).
2 Normative references
This clause of Part 1 is applicable except as follows.
Addition:
IEC 60584-1, Thermocouples – Part 1: EMF specifications and tolerances
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 60068-2-52:2017, Environmental testing – Part 2-52: Tests – Test Kb: Salt mist, cyclic
(sodium chloride solution)
3 Terms and definitions
This clause of Part 1 is applicable except as follows.
3.1 Definitions relating to physical characteristics
3.1.6
rated current
Note 101 to entry: For appliances having more than three heating units per phase, other than those that are
controlled by programmable electronic circuits that limit the number of heating elements and/or motors from being
energized at the same time, a diversity factor is applied to the rated current or rated power input when determining
the current used to establish the size of the terminals and the nominal cross-sectional area of the supply cord. The
diversity factor F is calculated from the following formula, where N is the number of heating units per phase that
can be energized together:
0,65
F 0,35+
N
3.1.9 Modification:
normal operation
Replace the first paragraph with the following:
operation of the appliance as specified in 3.1.9.101 to 3.1.9.107
Replace the first dashed item of the second paragraph with the following:
– the battery that is fully discharged is charged with the battery-operated appliance
operating as specified, if allowed by the construction of the appliance.
=
– 10 – IEC 60335-2-6:2024 © IEC 2024
3.1.9.101 Hob elements, other than induction hob elements and induction wok elements,
are operated with vessels containing cold water. The vessel is made of unpolished commercial
quality aluminium, has a flat bottom and is covered with a lid that is positioned so that steam
does not affect the tests. Thermal controls are adjusted to their highest setting until the water
boils and then adjusted so that the water boils gently. Water is added to maintain the level
during boiling.
In case of doubt, vessels as specified in Figure 101 are used.
Induction hob elements are operated with vessels as specified in Figure 102 that contain
cooking oil at room temperature. Thermal controls are adjusted to their highest setting until
the oil temperature reaches 180 °C ± 4 °C and then adjusted so that this temperature is
maintained. The oil temperature is measured 10 mm above the centre of the bottom of the
vessel.
Induction hob elements in a flexible induction cooking zone are operated with vessels
according to Figure 102 with diameters as specified in Figure 101 as follows:
a) the maximum number of vessels which can be separately controlled at the same time,
arranged to cover the flexible induction cooking zone as far as possible. Any combination
of vessels giving the most unfavourable results shall be used for the test. Several vessels
with the same diameter may be used;
b) the vessel which provides the highest power density (W/cm );
c) the smallest vessel that allows an induction hob element to operate.
Operation as specified in a), b) or c), that results in the most unfavourable condition for the
tests specified in the relevant subclauses is applied.
Induction wok elements are operated with a wok having an equivalent sphere diameter that
does not differ from the equivalent sphere diameter of the induction wok element cavity by
more than %. This wok can be supplied by the manufacturer.
− 1
The wok is made of low carbon steel having a maximum carbon content of 0,08 % and a
thickness of 2 mm ± 0,5 mm. The height of the wok shall be approximately twice the depth of
the induction wok element cavity.
The wok is filled to approximately half of its height with cooking oil at room temperature.
Thermal controls are adjusted to their highest setting until the oil temperature reaches
180 °C ± 4 °C and then adjusted so that this temperature is maintained. The oil temperature is
measured 10 mm above the centre of the bottom of the vessel.
For all hob elements other than those in a flexible induction cooking zone and induction
wok elements, the diameter of the bottom of the vessel is approximately equal to the diameter
of the cooking zone and the quantity of liquid is specified in Table 101. The vessel is positioned
centrally on the cooking zone.
If several cooking zones are marked for one hob element, the most unfavourable cooking
zone is used for the test.
For non-circular cooking zones, the smallest non-circular vessel is used which will cover the
cooking zone as far as possible, taking into account the hob rim and the other vessels. The
quantity of liquid is determined on the basis of the minor diameter of the cooking zone.

IEC 60335-2-6:2024 © IEC 2024 – 11 –
Table 101 – Quantity of liquid in the vessel
Diameter of cooking zone Quantity of water or oil
mm l
≤ 110 0,6
1,0
> 110 and ≤ 145
1,5
> 145 and ≤ 180
> 180 and ≤ 220 2,0
> 220 and ≤ 300 3,0
3.1.9.102 Ovens and steam convection ovens are operated empty with the door closed.
Thermal controls are adjusted so that the mean temperature in the centre of the oven is
maintained at
– 220 °C ± 4 °C for ovens with forced air circulation;
– 240 °C ± 4 °C for other ovens.
If the temperature cannot be attained, the thermal control is adjusted to its highest setting.
Ovens without thermal controls are switched on and off so that the temperature in the centre
of the oven is maintained at 240 °C ± 15 °C.
Atmospheric steam ovens and pressure steam ovens are operated in accordance with the
instructions. Lids, doors and covers are in position and closed. Controls are adjusted to their
highest setting until the cooking temperature is reached and then adjusted to the lowest setting
that maintains this temperature.
Steam generators intended to be filled by hand are filled according to the instructions, water
being added to maintain the steam generation.
Steam generators intended to be filled automatically are connected to a water supply, the
pressure of which is set according to the instructions.
The supply water has a temperature of
– 15 °C ± 5 °C for appliances to be connected to a cold water supply;
– 60 °C ± 5 °C or the temperature indicated in the instructions, whichever is the higher, for
appliances to be connected to a hot water supply.
Steam convection ovens are also operated while generating steam but with the thermal
controls adjusted as for operation without steam.
3.1.9.103 Grills are operated empty with the grill pan and food supports in the most
unfavourable position for normal use, the door and any other accessories being positioned in
accordance with the instructions. In the absence of such instructions, the door and other
accessories are placed in the most unfavourable position in which they can be left. Thermal
controls are adjusted to their highest setting. However, if the instructions for grills incorporated
in ovens specify a lower setting, this setting is used. Any reflectors intended to be placed above
heating elements are in position.
3.1.9.104 Rotating spits in ovens or grills are operated with the load on the rotating spit as
shown in Figure 103. The load is positioned on the rotary spit so that the fixing screw contacts
the diameter of the spit. The appliance is operated taking into account the instructions with
regard to:
– the heating elements to be operated;
– the setting of the thermal control;
– the position of the door and grill pan.

– 12 – IEC 60335-2-6:2024 © IEC 2024
In the absence of such instructions, the control is adjusted to its highest setting and the door is
fully open or is placed in the most unfavourable intermediate position in which it can be left.
Any grill pan is placed in its lowest position.
3.1.9.105 Warming drawers and similar compartments are operated in the closed position with
their controls adjusted to the highest setting.
3.1.9.106 Griddles are operated so that the temperature at the centre of the heated surface
is maintained at 275 °C ± 15 °C by adjusting their thermal controls or by switching the supply
on or off.
3.1.9.107 Cooking ranges are operated with their individual heating units being operated
under their stated conditions of normal operation.
3.1.101
rated water pressure
water pressure assigned to the appliance by the manufacturer
3.1.102
rated cooking pressure
maximum working pressure of pressure steam ovens assigned by the manufacturer to the
pressurized parts of the appliance
3.5 Definitions relating to types of appliances
3.5.101
oven
appliance having a heated cavity with a door and constructed so that food, which can be in a
container, can be placed on a shelf
3.5.102
grill
heating unit constructed so that the food is supported on a grid or spit and is cooked by radiant
heat
Note 1 to entry: The cooking operation in a grill is known as grilling or broiling.
3.5.103
hob
appliance that incorporates a hob surface and one or more hob elements, and is built in or
part of a cooking range
3.5.104
cooking range
appliance incorporating a hob and an oven and which can incorporate a grill or griddle
3.5.105
pyrolytic self-cleaning oven
oven in which cooking deposits are removed by heating the oven to a temperature exceeding
350 °C
3.5.106
steam oven
oven intended for cooking food by steam in the appliance

IEC 60335-2-6:2024 © IEC 2024 – 13 –
3.5.106.1
steam convection oven
steam oven intended for cooking food by conventional heating and steam generated at
atmospheric pressure in the appliance
Note 1 to entry: The operation temperature can exceed the boiling point of water.
3.5.106.2
atmospheric steam oven
steam oven in which the pressure within the cooking compartment differs from atmospheric
pressure by 50 kPa or less
3.5.106.3
pressure steam oven
steam oven intended for cooking food by direct steam generated at a pressure that is at least
50 kPa higher than atmospheric pressure
3.5.107
griddle
heating unit having a surface on which the food is placed directly for cooking
3.5.108
induction hob
hob containing at least one induction hob element or one induction wok element
3.6 Definitions relating to parts of an appliance
3.6.101
heating unit
any part of the appliance that fulfils an independent cooking or warming function
Note 1 to entry: Examples are hob elements, ovens, grills and warming drawers.
3.6.102
hob surface
horizontal part of the appliance on which vessels can be placed
3.6.103
hob element
heating unit attached to the hob surface or positioned below the cooking zone
3.6.104
induction hob element
hob element that heats metallic vessels by means of eddy currents
Note 1 to entry: The eddy currents are induced in the vessel by the electromagnetic field of a coil.
3.6.105
induction wok element
induction hob element with the hob surface of an approximate spherical shape to accept
a wok
3.6.106
cooking zone
area marked on a hob surface where the vessel is placed for heating food
Note 1 to entry: When a hob element protrudes above the hob surface, its surface is the cooking zone.

– 14 – IEC 60335-2-6:2024 © IEC 2024
3.6.107
pan detector
device incorporated in a hob element that prevents its operation unless a vessel is placed on
the cooking zone
3.6.108
touch control
control actuated by contact or proximity of a finger, with little or no movement of the contact
surface
3.6.109
temperature-sensing probe
device that is inserted into the food to measure its temperature and which is a part of an oven
control
3.6.110
flexible induction cooking zone
area on a cooking zone with induction hob elements that is not marked to indicate where
vessels are to be placed for heating food
3.7 Definitions relating to safety components
3.7.101
pressure regulator
control that maintains the pressure at a particular value during normal use
3.7.102
pressure-relief device
control that limits the pressure under abnormal operating conditions
3.7.103
automatic regulation system
regulation system for hobs that uses wired or wireless sensors to enable and control an
automatic cooking process and maintaining a target value
Note 1 to entry: Wireless sensors can communicate by means of radio communication.
Note 2 to entry: The target value can be e.g. temperature, time, power level.
3.8 Definitions relating to miscellaneous matters
3.8.101
open deck
area that is exposed to marine environment
3.8.102
dayroom
area that can be exposed to marine environment from time to time
3.11 Definitions relating to remote functionality
3.11.4
remote communication
Note 101 to entry: Transmission of data for operating functions that do not control heating units (e.g. brightness
of displays or buzzer sounds) that can be initiated by the user out of sight of the appliance is considered remote
communication, but not considered remote operation.
Note 102 to entry: In the case where a wireless sensor uses short range communication technology and exclusively
communicates with the hob through its connectivity module to exchange sensor data, the communication between
the wireless sensor and the hob is not considered as communication through a public network.

IEC 60335-2-6:2024 © IEC 2024 – 15 –
3.11.5
remote operation
Note 101 to entry: Remote operation refers to commands initiated by the user out of sight of the appliance that
control intended functions such as the control of heating units.
Note 102 to entry: Remote communication including change of target values of the system which require manual
confirmation at the hob is not considered remote operation.
Note 103 to entry: General guidance for the application of remote automatic regulation systems for hobs is given
in the informative Annex AA, Figure AA.1.
3.11.101
remote automatic regulation system
automatic regulation system that can be initiated or modified by means of remote
communication
4 General requirement
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable except as follows.
5.3 Addition:
For pyrolytic self-cleaning ovens, the tests of 22.108 to 22.111 are carried out before the
tests of Clause 19.
5.4 Addition:
Appliances that also use gas are supplied with gas at the appropriate rated pressure. Vessels
having a diameter of approximately 220 mm are filled with 2 l of water, covered with a lid and
placed on the hob burners. The controls are adjusted to their highest setting until the water
boils. They are then adjusted so that the water simmers, water being added when necessary to
maintain the level.
5.101 Class III temperature-sensing probes are only subjected to the tests of Clause 19.
5.102 Steam convection ovens are tested as ovens.
6 Classification
This clause of Part 1 is applicable except as follows.
6.1 Modification:
Replace the first paragraph with the following:
Appliances shall be class I, class II or class III.
Addition:
Cooking ranges incorporating socket-outlets shall be class I appliances.

– 16 – IEC 60335-2-6:2024 © IEC 2024
6.2 Addition:
Ovens for open deck use shall be IPX6.
7 Marking and instructio
...