SIST EN ISO 17871:2020/kFprA2:2026

SLOVENSKI STANDARD
SIST EN ISO 17871:2020/oprA2:2026
01-marec-2026
Plinske jeklenke - Ventili jeklenk za hitro razbremenitev - Specifikacija in
preskušanje tipa - Dopolnilo A2 (ISO 17871:2020/DAM 2:2026)
Gas cylinders - Quick-release cylinder valves - Specification and type testing -
Amendment 2 (ISO 17871:2020/DAM 2:2026)
Gasflaschen - Schnellöffnungs-Flaschenventile - Spezifikation und Baumusterprüfung -
Änderung 2 (ISO 17871:2020/DAM 2:2026)
Bouteilles à gaz - Robinets de bouteilles à ouverture rapide - Spécifications et essais de
type - Amendement 2 (ISO 17871:2020/DAM 2:2026)
Ta slovenski standard je istoveten z: EN ISO 17871:2020/prA2
ICS:
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
SIST EN ISO 17871:2020/oprA2:2026 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN ISO 17871:2020/oprA2:2026

SIST EN ISO 17871:2020/oprA2:2026
DRAFT
Amendment
ISO 17871:2020/
DAM 2
ISO/TC 58/SC 2
Gas cylinders — Quick-release
Secretariat: AFNOR
cylinder valves — Specification and
type testing
Voting begins on:
2026-01-15
AMENDMENT 2
Voting terminates on:
2026-04-09
Bouteilles à gaz — Robinets de bouteilles à ouverture rapide —
Spécifications et essais de type
AMENDEMENT 2
ICS: 23.020.35
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO 17871:2020/DAM 2:2026(en)
SIST EN ISO 17871:2020/oprA2:2026
DRAFT
ISO 17871:2020/DAM 2:2026(en)
Amendment
ISO 17871:2020/
DAM 2
ISO/TC 58/SC 2
Gas cylinders — Quick-release
Secretariat: AFNOR
cylinder valves — Specification and
type testing
Voting begins on:
AMENDMENT 2
Voting terminates on:
Bouteilles à gaz — Robinets de bouteilles à ouverture rapide —
Spécifications et essais de type
AMENDEMENT 2
ICS: 23.020.35
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2026
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO 17871:2020/DAM 2:2026(en)
ii
SIST EN ISO 17871:2020/oprA2:2026
ISO 17871:2020/DAM 2:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder valves.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iii
SIST EN ISO 17871:2020/oprA2:2026

SIST EN ISO 17871:2020/oprA2:2026
ISO 17871:2020/DAM 2:2026(en)
Gas cylinders — Quick-release cylinder valves — Specification
and type testing
AMENDMENT 2
1  Scope, paragraph after NOTE 2
Replace the paragraph with the following paragraph:
“This document only covers the function of a quick-release cylinder valve as a closure. Other functions that
are possibly integrated in the valve can be covered by other standards. Such standards do however not
constitute requirements according to this document.”

1  Scope, new NOTE 3
Add the following Note at the end of clause 3:
“NOTE 3 Certain specific requirements for quick-release cylinder valves for fixed fire-fighting systems
in addition to those that are given in this document are specified in ISO 16003 and at a regional level, e.g. in
EN 12094–4. Certain specific requirements for residual pressure valves (RPV), in addition to those that are
given in this document, are given in ISO 15996.”

2  Reference to ISO 10297 and ISO 17879
Substitute “ISO 10297:2014+Amd1:2017” with “ISO 10297:2024” and “ISO 17879:2017” with “ISO 17879:2026”.

4.1  First paragraph
Substitute the first paragraph with the following paragraph:
“Quick-release cylinder valves shall comply with all requirements of ISO 10297, ISO 17879 or ISO 23826
(except Clause 8), as applicable, unless this document expressly allows differing requirements or stipulates
additional requirements.”
4.1  Last paragraph
Substitute “ISO 10297:2014+Amd1:2017, 5.2” with “ISO 10297:2024, 5.2” and “ISO 17879:2017, 5.2” with
“ISO 17879:2026, 5.2”.
4.2.1  First paragraph
Substitute the first para
...