oSIST prEN 16898:2015
(Main)Safety and control devices for gas burners and gas burning appliances - Gas filters having a maximum working pressure up to and including 600 kPa
Safety and control devices for gas burners and gas burning appliances - Gas filters having a maximum working pressure up to and including 600 kPa
This European Standard specifies the safety, design, construction, and performance requirements and testing for gas filters for burners and appliances burning one or more gaseous fuels.
This European Standard is applicable to
- gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal connection size up to and including DN 250 for use with one or more fuel gases in accordance with EN 437:2003+A1:2009,
- gas filters specified as pressure accessories as defined by EU Directive 97/23/EC (see Annex F).
NOTE For pressure accessories, the requirements of EN 13611:2015, Annex F also applies.
This European Standard is not applicable to gas filters that are connected directly to mains pipe-work or to a container that maintains a standard distribution pressure.
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasbrennstoffgeräte - Gasfilter für einen Betriebsdruck bis einschließlich 600 kPa
Diese Europäische Norm legt die Sicherheits-, Konstruktions- und Funktionsanforderungen sowie die Prüfung für Gasfilter für Brenner und Brennstoffgeräte für einen oder mehrere gasförmige(n) Brennstoff(e) fest.
Diese Europäische Norm gilt für:
- Gasfilter mit einem angegebenen höchsten Eingangsdruck bis einschließlich 600 kPa mit Anschluss-nennweiten bis einschließlich DN 250 zur Verwendung mit einem oder mehreren Brenngas(en) nach EN 437:2003A1:2009;
- Gasfilter, die als druckhaltende Ausrüstungsteile nach Richtlinie 97/23/EG festgelegt sind (siehe Anhang F).
ANMERKUNG Für druckhaltende Ausrüstungsteile gelten ebenfalls die Anforderungen nach EN 13611:2015, Anhang F.
Diese Europäische Norm gilt nicht für Gasfilter, die direkt an die Gasversorgungsleitung angeschlossen sind oder einen Behälter, der einen Standardverteilungsdruck aufrechterhält.
Équipements auxiliaires pour brûleurs à gaz et appareils à gaz - Filtres à gaz ayant une pression de service maximale inférieure ou égale à 600 kPa
La présente Norme européenne spécifie les exigences en matière de sécurité, de conception, de construction et de performance ainsi que les essais applicables aux filtres à gaz pour brûleurs et appareils utilisant un ou plusieurs combustibles gazeux.
La présente Norme européenne est applicable :
- aux filtres à gaz dont la pression amont maximale déclarée est inférieure ou égale à 600 kPa, de diamètre nominal de raccordement inférieur ou égal à DN 250, et conçus pour une utilisation avec un ou plusieurs combustibles gazeux conformes à l’EN 437:2003+A1:2009 ;
- aux filtres à gaz désignés comme accessoires sous pression, comme défini dans la Directive Européenne 97/23/CE (voir Annexe F).
NOTE En ce qui concerne les accessoires sous pression, les exigences de l'Annexe F de l'EN 13611:2015 s'appliquent également.
La présente Norme européenne ne s'applique pas aux filtres à gaz qui sont raccordés directement au réseau de distribution ou à un conteneur qui maintient en aval une pression de distribution normalisée.
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - Filtri za plin za najvišji delovni tlak do vključno 600 kPa
General Information
- Status
- Not Published
- Public Enquiry End Date
- 09-Nov-2015
- Technical Committee
- PLN - Gas appliances for domestic use
- Current Stage
- 98 - Abandoned project (Adopted Project)
- Start Date
- 15-May-2019
- Due Date
- 20-May-2019
- Completion Date
- 15-May-2019
- Directive
- Not Harmonized2009/142/EC - Appliances burning gaseous fuels
Not Harmonized97/23/EC - Pressure equipment
Relations
- Effective Date
- 01-May-2020
Overview
oSIST prEN 16898:2015 is a European standard that establishes the safety, design, construction, performance, and testing requirements for gas filters used in gas burners and appliances that burn gaseous fuels. Developed by the Slovenian Institute for Standardization (SIST), this standard applies to gas filters with a maximum working pressure up to and including 600 kPa and nominal connection sizes up to DN 250. These filters are intended for use with one or more fuel gases in accordance with EN 437:2003+A1:2009 and may be specified as pressure accessories as defined by EU Directive 97/23/EC.
This standard is crucial for manufacturers, suppliers, and installers looking for compliance and a high level of safety in filtration components of gas-burning systems. It explicitly does not cover gas filters directly connected to mains pipe-work or containers maintaining a standard distribution pressure.
Key Topics
Scope and Applicability:
- Covers gas filters for use up to 600 kPa.
- Applies to connection sizes up to DN 250.
- Relevant for burners and appliances using various gaseous fuels.
Design and Construction Requirements:
- Mechanical parts must meet strict standards - no moving parts or breather holes are allowed.
- Filter elements must be easily replaceable and securely fixed after pressure testing.
- Materials used must comply with EN 13611:2015 and associated provisions for pressurized components.
- Zinc alloys are not permitted in the construction.
Performance and Filtration Efficiency:
- Minimum filtration efficiency is defined depending on filter material (85% for needle-felt or cellulose, 75% for polypropylene fiber).
- Detailed test procedures, including dust dosing and leak-tightness assessments, ensure reliability and effectiveness.
Marking and Instructions:
- Clear, permanent marking of manufacturer details, pressure ratings, temperature range, gas flow direction, and manufacturing date.
- Installation and operating manuals must specify gas filter suitability, pressures, temperatures, installation positions, connection details, and performance limits.
Compliance with EU Directives:
- Aligns with Directive 2009/142/EC for appliances burning gaseous fuels.
- Aligns with Directive 97/23/EC for pressure equipment.
Applications
Gas filters compliant with oSIST prEN 16898:2015 are essential in the following practical contexts:
Industrial Gas Burning Equipment:
Ensures reliable removal of particulates (e.g., dust, rust) from gas supply lines in industrial burners to protect downstream equipment and enhance combustion safety.Commercial and Residential Appliances:
Applied in boilers, heaters, and other gas appliances to maintain gas cleanliness, reduce risk of clogging, and ensure consistent appliance operation.Pressure Accessories:
Suitable for systems that fall under the scope of the Pressure Equipment Directive (PED), where additional requirements for safety and pressure resilience are critical.System Maintenance:
Facilitates routine maintenance thanks to standardized requirements for filter element replacement and servicing documentation.Product Certification and Market Access:
Enables manufacturers and suppliers of gas filters to demonstrate conformity with EU safety and performance requirements, facilitating market acceptance and regulatory compliance.
Related Standards
EN 13611:2015
General requirements for safety and control devices for burners and appliances burning gaseous and/or liquid fuels.EN 437:2003+A1:2009
Detailing fuel gases and their properties, essential for determining suitability of filters with various gas types.EN 779:2012
Standard for particulate air filters used in general ventilation, referenced for test procedures and performance criteria.EN 60312-1:2013
Methods for measuring vacuum cleaner performance, referenced for dust filtration efficiency testing.ISO 12103-1:1997
Provides specifications for test dust used in filter evaluation test methods.Relevant EU Directives:
- 2009/142/EC (Appliances burning gaseous fuels)
- 97/23/EC (Pressure Equipment Directive)
Implementing oSIST prEN 16898:2015 ensures industry best practices for gas filter safety and performance, supports regulatory compliance, and safeguards gas-burning installations across a range of applications.
Get Certified
Connect with accredited certification bodies for this standard
DNV
DNV is an independent assurance and risk management provider.
Lloyd's Register
Lloyd's Register is a global professional services organisation specialising in engineering and technology.
DNV Energy Systems
Energy and renewable energy certification.
Sponsored listings
Frequently Asked Questions
oSIST prEN 16898:2015 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Safety and control devices for gas burners and gas burning appliances - Gas filters having a maximum working pressure up to and including 600 kPa". This standard covers: This European Standard specifies the safety, design, construction, and performance requirements and testing for gas filters for burners and appliances burning one or more gaseous fuels. This European Standard is applicable to - gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal connection size up to and including DN 250 for use with one or more fuel gases in accordance with EN 437:2003+A1:2009, - gas filters specified as pressure accessories as defined by EU Directive 97/23/EC (see Annex F). NOTE For pressure accessories, the requirements of EN 13611:2015, Annex F also applies. This European Standard is not applicable to gas filters that are connected directly to mains pipe-work or to a container that maintains a standard distribution pressure.
This European Standard specifies the safety, design, construction, and performance requirements and testing for gas filters for burners and appliances burning one or more gaseous fuels. This European Standard is applicable to - gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal connection size up to and including DN 250 for use with one or more fuel gases in accordance with EN 437:2003+A1:2009, - gas filters specified as pressure accessories as defined by EU Directive 97/23/EC (see Annex F). NOTE For pressure accessories, the requirements of EN 13611:2015, Annex F also applies. This European Standard is not applicable to gas filters that are connected directly to mains pipe-work or to a container that maintains a standard distribution pressure.
oSIST prEN 16898:2015 is classified under the following ICS (International Classification for Standards) categories: 27.060.20 - Gas fuel burners. The ICS classification helps identify the subject area and facilitates finding related standards.
oSIST prEN 16898:2015 has the following relationships with other standards: It is inter standard links to SIST EN 16898:2022. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
oSIST prEN 16898:2015 is associated with the following European legislation: EU Directives/Regulations: 2009/142/EC, 2014/68/EU, 97/23/EC; Standardization Mandates: M/071, M/BC/CEN/89/6. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
oSIST prEN 16898:2015 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2015
9DUQRVWQHLQQDG]RUQHQDSUDYH]DSOLQVNHJRULOQLNHLQSOLQVNHDSDUDWH)LOWUL]D
SOLQ]DQDMYHþMLGHORYQLWODNGRYNOMXþQRN3D
Safety and control devices for gas burners and gas burning appliances - Gas filters
having a maximum working pressure up to and including 600 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasbrennstoffgeräte - Gasfilter
für einen Betriebsdruck bis einschließlich 600 kPa
Équipements auxiliaires pour brûleurs à gaz et appareils à gaz - Filtres à gaz ayant une
pression de service maximale inférieure ou égale à 600 kPa
Ta slovenski standard je istoveten z: prEN 16898
ICS:
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2015
ICS 27.060.20
English Version
Safety and control devices for gas burners and gas burning
appliances - Gas filters having a maximum working pressure up
to and including 600 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und
Gasbrennstoffgeräte - Gasfilter für einen Betriebsdruck bis
einschließlich 600 kPa
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 58.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16898:2015 E
worldwide for CEN national Members.
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 Classification .7
5 Test conditions and uncertainty of measurements .7
6 Design and construction requirements .7
7 Performance . 10
8 Electrical requirements . 12
9 Electromagnetic compatibility (EMC) . 12
10 Marking, installation and operating instructions . 13
Annex A (informative) Void . 14
Annex B (informative) Leak-tightness test for gas controls – volumetric method . 15
Annex C (informative) Leak-tightness test for gas controls – pressure loss method . 16
Annex D (normative) Conversion of pressure loss into leakage rate . 17
Annex E (normative) Electrical/electronic component fault modes . 18
Annex F (normative) Additional requirements for safety accessories and pressure accessories as
defined in EU Directive 97/23/EC . 19
Annex G (normative) Materials for pressurized parts . 20
Annex H (normative) Additional materials for pressurized parts . 21
Annex I (normative) Requirements for controls used in DC supplied burners and appliances
burning gaseous or liquid fuels . 22
Annex J (normative) Method for the determination of a Safety integrity level (SIL) . 23
Annex K (normative) Method for the determination of a Performance Level (PL) . 24
Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance Level
(PL) . 25
Annex M (normative) Reset functions . 26
Annex N (informative) Guidance document on Environmental Aspects . 27
Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures . 28
Annex AA (normative) Dust collecting device . 29
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2009/142/EC relating to appliances burning gaseous fuels . 30
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 97/23/EC concerning pressure equipment . 32
Bibliography . 33
Figures
Figure 1 — Standards house . 5
Figure 2 — Test apparatus filtration efficiency . 12
Figure AA.1 — Outlet filter . 29
Tables
Table AA.1 — Specifications for dust collecting bag . 29
Table ZA.1 — Correspondence between this European Standard and Directive 2009/142/EC
relating to appliances burning gaseous fuels . 30
Table ZB.1 — Correspondence between this European Standard and Directive 97/23/EC
concerning pressure equipment . 32
Foreword
This document (prEN 16898:2015) has been prepared by Technical Committee CEN/TC 58 “Safety and
control devices for burners and appliances burning gaseous or liquid fuels”, the secretariat of which is held by
BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directives 2009/142/EC and
97/23/EC.
For relationship with EU Directive(s), see informative Annex ZA and Annex ZB, which are integral parts of this
document.
Introduction
The generic requirements for controls are given in EN 13611:2015 and methods for classification and
assessment for new controls and control functions are given in prEN 14459:2014, Clauses 1 up to and
including 7.13 (see Figure 1).
The requirements for controls are given in the specific control standard (see Figure 1).
Multifunctional Controls (MFC) according to EN 126:2012 with two or more controls and Application Control
Functions, e.g. the Gas Shut-off Control Function, being inherently multifunctional controls. Each control
integrated in the MFC meets the applicable requirements of the relevant control standard(s). In addition,
EN 126:2012 covers requirements for the safety related interactions between the different devices.
Figure 1 — Standards house
This control standard refers to clauses of EN 13611:2015 or adapts it by stating “with the following
modification”, “with the following addition”, “is replaced by the following” or “is not applicable” in the
corresponding clause. This document adds clauses or sub-clauses to the structure of EN 13611:2015 which
are particular to this standard, i.e. sub-clauses or annexes which are additional to those in EN 13611:2015 are
numbered starting from 101 or are designated as Annex AA. It should be noted that these clauses and sub-
clauses are not indicated as an addition.
1 Scope
This European Standard specifies the safety, design, construction, and performance requirements and testing
for gas filters for burners and appliances burning one or more gaseous fuels.
This European Standard is applicable to
— gas filters with declared maximum inlet pressure up to and including 600 kPa, of nominal connection size
up to and including DN 250 for use with one or more fuel gases in accordance with
EN 437:2003+A1:2009;
— gas filters specified as pressure accessories as defined by EU Directive 97/23/EC (see Annex F).
NOTE For pressure accessories, the requirements of EN 13611:2015, Annex F also applies.
This European Standard is not applicable to gas filters that are connected directly to mains pipe-work or to a
container that maintains a standard distribution pressure.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 779:2012, Particulate air filters for general ventilation — Determination of the filtration performance
EN 13611:2015, Safety and control devices for burners and appliances burning gaseous and/or liquid fuels —
General Requirements
EN 60312-1:2013, Vacuum cleaners for household use — Part 1: Dry vacuum cleaners — Methods for
measuring the performance (IEC 60312-1:2010, modified + A1:2011, modified)
ISO 12103-1:1997, Road vehicles — Test dust for filter evaluation — Part 1: Arizona test dust
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13611:2015 and the following apply.
3.1
gas filter
device that segregates particles from the gas flow e. g. dust and rust
3.2
filter material
part of the filter, which segregates particles
3.3
filter element
filter material with support
3.4
filtration efficiency
percentage ratio of filtered amount of dust to charged amount of dust
4 Classification
4.1 Classes of control
EN 13611:2015, 4.1 is not applicable.
4.2 Groups of control
Shall be according to EN 13611:2015, 4.2.
4.3 Classes of control functions
EN 13611:2015, 4.3 is not applicable.
4.4 Types of DC supplied controls
EN 13611:2015, 4.4 is not applicable.
5 Test conditions and uncertainty of measurements
Shall be according to EN 13611:2015, Clause 5.
6 Design and construction requirements
6.1 General
Shall be according to EN 13611:2015, 6.1.
6.2 Mechanical parts of the control
6.2.1 Appearance
Shall be according to EN 13611:2015, 6.2.1.
6.2.2 Holes
Shall be according to EN 13611:2015, 6.2.2.
6.2.3 Breather holes
EN 13611:2015, 6.2.3 is replaced by the following:
Breather holes are not allowed.
EN 13611:2015, 6.2.4 is not applicable (see 6.2.3).
6.2.4 Screwed fastenings
Shall be according to EN 13611:2015, 6.2.4.
6.2.5 Jointing
Shall be according to EN 13611:2015, 6.2.5.
6.2.6 Moving parts
EN 13611:2015, 6.2.6 is replaced by the following:
Moving parts are not allowed.
6.2.7 Sealing caps
Shall be according to EN 13611:2015, 6.2.7.
6.2.8 Dismantling and reassembly
Shall be according to EN 13611:2015, 6.2.8.
6.2.9 Auxiliary canals and orifices
EN 13611:2015, 6.2.9 is not applicable.
6.2.10 Presetting device
EN 13611:2015, 6.2.10 is not applicable.
6.2.101 Filter element replacement
— The filter lid shall be removable with commonly available tools.
— The filter insert shall be easily replaceable when following the installation and operation instruction.
— Non-metallic seals e.g. O-rings which provide the external leak tightness shall be enclosed.
6.2.102 Fixing of filter element
6.2.102.1 Requirement
The filter element shall remain fixed and in place after the test of 6.2.102.2.
6.2.102.2 Test
Block the filter element with tape of less than 0,05 mm thickness covering the whole inlet side of the filter.
Then pressurize the inlet of the gas filter to 1,5 times of the maximum pressure difference of the filter element
as stated in the installation and operating instruction.
Repeat the test 5 times.
Check conformity to 6.2.102.1 after the test.
6.3 Materials
6.3.1 General material requirements
Shall be according to EN 13611:2015, 6.3.1 with the following addition:
Materials shall conform to EN 13611:2015, Annexes F to H, if applicable.
6.3.2 Housing
Shall be according to EN 13611:2015, 6.3.2.
6.3.3 Zinc alloys
EN 13611:2015, 6.3.3 is replaced by the following:
Zinc alloys shall not be used.
6.3.4 Springs
EN 13611:2015, 6.3.4 is not applicable.
6.3.5 Resistance to corrosion and surface protection
Shall be according to EN 13611:2015, 6.3.5.
6.3.6 Impregnation
Shall be according to EN 13611:2015, 6.3.6.
6.3.7 Seals for glands for moving parts
EN 13611:2015, 6.3.7 is not applicable.
6.4 Gas Connections
6.4.1 Making connections
Shall be according to EN
...