SIST EN ISO 11114-5:2022

SLOVENSKI STANDARD
01-september-2022
Plinske jeklenke - Združljivost materialov za ventil in jeklenko s plinom - 5. del:
Preskusne metode za vrednotenje plastičnih notranjih prevlek (ISO 11114-5:2022)
Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 5:
Test methods for evaluating plastic liners (ISO 11114-5:2022)
Gasflaschen - Verträglichkeit von Werkstoffen für Gasflaschen und Ventile mit den in
Berührung kommenden Gasen - Teil 5: Prüfverfahren zur Bewertung der
Kunststoffinnenbehälter (ISO 11114-5:2022)
Bouteilles à gaz - Compatibilité des matériaux des bouteilles et des robinets avec les
contenus gazeux - Partie 5: Méthodes d’essai pour l’évaluation des liners en plastique
(ISO 11114-5:2022))
Ta slovenski standard je istoveten z: EN ISO 11114-5:2022
ICS:
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11114-5
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2022
EUROPÄISCHE NORM
ICS 23.020.35
English Version
Gas cylinders - Compatibility of cylinder and valve
materials with gas contents - Part 5: Test methods for
evaluating plastic liners (ISO 11114-5:2022)
Bouteilles à gaz - Compatibilité des matériaux des Gasflaschen - Verträglichkeit von Werkstoffen für
bouteilles et des robinets avec les contenus gazeux - Gasflaschen und Ventile mit den in Berührung
Partie 5: Méthodes d'essai pour l'évaluation des liners kommenden Gasen - Teil 5: Prüfverfahren zur
en plastique (ISO 11114-5:2022) Bewertung der Kunststoffinnenbehälter (ISO 11114-
5:2022)
This European Standard was approved by CEN on 26 December 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11114-5:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11114-5:2022) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2022, and conflicting national standards shall be
withdrawn at the latest by July 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11114-5:2022 has been approved by CEN as EN ISO 11114-5:2022 without any
modification.
INTERNATIONAL ISO
STANDARD 11114-5
First edition
2022-01
Gas cylinders — Compatibility of
cylinder and valve materials with gas
contents —
Part 5:
Test methods for evaluating plastic
liners
Bouteilles à gaz — Compatibilité des matériaux des bouteilles et des
robinets avec les contenus gazeux —
Partie 5: Méthodes d’essai pour l’évaluation des liners en plastique
Reference number
ISO 11114-5:2022(E)
ISO 11114-5:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 11114-5:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Tests to be performed on specimens . 2
5.1 Permeation test . 2
5.1.1 Disc samples . 2
5.1.2 Test bench and set-up . 3
5.1.3 Procedure . 5
5.1.4 Calculation of the permeability coefficient. 6
5.1.5 Recording and interpretation of test results . 6
5.2 Swelling/blistering test . 7
5.2.1 Disc samples . 7
5.2.2 Recording and interpretation of tests results . 7
5.3 Ageing test . 8
5.3.1 Samples . 8
5.3.2 Procedure . 8
5.3.3 Recording and interpretation of the results . 8
6 Tests to be performed on cylinders .9
6.1 Liner collapse due to internal pressure in the cylinder being below atmospheric
pressure . 9
6.1.1 General . 9
6.1.2 Procedure . 9
6.1.3 Evaluation parameters . 9
6.2 Permeability test . 9
6.2.1 General . 9
6.2.2 Procedure . 9
6.2.3 Evaluation parameters . 10
6.3 Liner collapse and blistering test . 10
6.3.1 General . 10
6.3.2 Procedure . 10
6.3.3 Evaluation parameters . 10
7 Rejection and rendering cylinders used for testing unserviceable .12
8 Test report .12
Bibliography .14
iii
ISO 11114-5:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 23, Transportable gas
cylinders, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
A list of all parts in the ISO 11114 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 11114-5:2022(E)
Introduction
Non-metallic materials are used for the manufacturing of liners of some composite gas cylinders and
therefore are in contact with gas contents.
The compatibility of plastic liners with gas cylinder contents is a key parameter for the manufacturing
of composite gas cylinders with plastic liners. Therefore, it is necessary to clarify such compatibility
and to give test procedures and evaluation parameters.
This document provides some testing methodologies to evaluate suitability of plastic materials
concerning the risks identified in ISO 11114-2. Furthermore, this document is intended to be used
together with the design standard (e.g. ISO 11515, EN 12245) which gives the requirements for certain
tests, as well as the criteria, while this document describes the test procedure.
v
INTERNATIONAL STANDARD ISO 11114-5:2022(E)
Gas cylinders — Compatibility of cylinder and valve
materials with gas contents —
Part 5:
Test methods for evaluating plastic liners
1 Scope
This document specifies some gas compatibility test methods to evaluate plastic materials suitable for
use in the manufacture of composite gas cylinder liners. It is also applicable to the evaluation of the
suitability of plastic matrix materials used for Type 5 cylinders.
Some fluids like water, used for cylinders testing, can react positively or negatively when in contact
with plastic liners. This compatibility issue is not covered by this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 178, Plastics — Determination of flexural properties
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 527 (all parts), Plastics — Determination of tensile properties
ISO 3167, Plastics — Multipurpose test specimens
ISO 8256, Plastics — Determination of tensile-impact strength
ISO 10286, Gas cylinders — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10286 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
blister
localized delamination or void within the liner material that looks like a bubble
3.2
maximum permissible filling mass
maximum mass of gas in kg which is allowed in a filled cylinder
Note 1 to entry: This term applies to liquefied gas.
[SOURCE: ISO 24431:2016, 3.13]
ISO 11114-5:2022(E)
3.3
Type 5 cylinder
fully wrapped cylinder without a liner and with composite reinforcement on both the cylindrical
portion and dome ends
4 General requirements
This document is designed to determine the suitability of the materials with regard to the risks
identified in ISO 11114-2 and to evaluate materials not listed in ISO 11114-2.
Two types of tests can be performed:
a) tests on discs or other specimens (see Clause 5);
b) tests on cylinders (see Clause 6).
To determine the suitability of materials for a given liner, testing shall be performed on cylinders in
accordance with Clause 6.
The tests on specimens should only be performed to compare different plastic materials (e.g. to select
the most suitable material) or to check if some zones on the liner permeate more than others, or both.
Tests on disc or specimen are difficult in case of Type 5 cylinders. Therefore, tests on cylinders are
recommended.
Some substances (e.g. moisture, sulfur compounds) can have a positive or negative effect on the
material performance, and this shall be taken into account when designing and carrying out tests.
These substances can be present in the gas or released by the plastic materials, or both.
Analysis of test gas shall be recorded to identify any possible contamination (e.g. moisture, sulfur
compounds, etc.) both prior to and after the test.
5 Tests to be performed on specimens
5.1 Permeation test
5.1.1 Disc samples
The disc samples shall be taken either from a liner or using samples manufactured according to the
intended process, such as injection moulding or blow moulding (e.g. to select the most suitable material).
NOTE 1 Treatments such as curing can affect the properties of the liner materials.
It is recommended that all process steps that influence the behaviour of the liner material that are
applied to the finished cylinder, including thermal treatment, are applied to the sp
...