SIST EN IEC 60317-89:2024
(Main)Specifications for particular types of winding wires - Part 89: Polyesterimide enameled round aluminum wire, class 200 (IEC 60317-89:2023)
Specifications for particular types of winding wires - Part 89: Polyesterimide enameled round aluminum wire, class 200 (IEC 60317-89:2023)
IEC 60317-89:2023 specifies the requirements of enamelled round aluminium winding wire of class 200 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is as follows:
grade 1: 0,250 mm up to and including 1,600 mm;
grade 2: 0,250 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and IEC 60317-0-3:2008/AMD1:2013. This International Standard is to be used in conjunction with IEC 60317-0-3:2008, its Amendment 1 (2013) and its Amendment 2 (2019).
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten Teil 89: Runddrähte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 200 (IEC 60317-89:2023)
Spécifications pour types particuliers de fils de bobinage - Partie 89: Fil de section circulaire en aluminium émaillé au polyestérimide, classe 200 (IEC 60317-89:2023)
IEC 60317-89-2023 spécifie les exigences relatives aux fils de bobinage de section circulaire en aluminium émaillé de classe 200, avec un revêtement simple à base de résine polyestérimide, qui peut être modifiée sous réserve qu'elle conserve l'identité chimique de la résine initiale et respecte l'ensemble des exigences spécifiées du fil. NOTE Une résine modifiée est une résine dont les propriétés chimiques ont été modifiées, ou qui contient un ou plusieurs additifs visant à améliorer certaines performances ou caractéristiques d’application. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est:
grade 1: de 0,250 mm jusqu’à 1,600 mm (inclus);
grade 2: de 0,250 mm jusqu’à 5,000 mm (inclus).
Les diamètres nominaux des conducteurs sont spécifiés à l’Article 4 de l’IEC 60317-0-3:2008 et de l’IEC 60317-0-3:2008/AMD1:2013. La présente Norme internationale doit être utilisée conjointement avec l'IEC 60317-0-3:2008, son Amendement 1 (2013) et son Amendement 2 (2019).
Specifikacije za posebne vrste navijalnih žic - 89. del: Okrogla aluminijeva žica, lakirana s poliesterimidnim lakom, razred 200 (IEC 60317-89:2023)
Standard IEC 60317-89:2023 določa zahteve za okroglo aluminijevo navijalno žico razreda 200, lakirano z eno samo prevleko na osnovi poliestramidne smole, ki se lahko spremeni, če ohrani kemijsko identiteto izvirne smole in izpolnjuje vse določene zahteve za žice. OPOMBA: Spremenjena smola je smola, ki je bila kemijsko spremenjena ali vsebuje enega ali več aditivov za izboljšanje določene lastnosti učinkovitosti ali uporabe. Razpon nazivnega premera prevodnika, ki ga zajema ta standard, je, kot sledi:
razred 1: od 0,250 mm do (vključno) 1,600 mm;
razred 2: od 0,250 mm do (vključno) 5,000 mm.
Nazivni premeri prevodnika so navedeni v točki 4 standarda IEC 60317-0-3:2008 in IEC 60317-0-3:2008/AMD1:2013. Ta mednarodni standard je treba uporabljati v povezavi s standardom IEC 60317-0-3:2008, njegovo spremembo 1 (2013) in spremembo 2 (2019).
General Information
- Status
- Published
- Public Enquiry End Date
- 31-Mar-2023
- Publication Date
- 17-Mar-2024
- Technical Committee
- I09 - Imaginarni 09
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 20-Sep-2023
- Due Date
- 25-Nov-2023
- Completion Date
- 18-Mar-2024
Relations
- Effective Date
- 03-Feb-2026
- Refers
SIST EN 60851-4:2016 - Winding wires - Test methods - Part 4: Chemical properties (IEC 60851-4:2016) - Effective Date
- 03-Feb-2026
- Effective Date
- 03-Feb-2026
- Effective Date
- 03-Feb-2026
Overview
SIST EN IEC 60317-89:2024 defines the requirements for polyesterimide enameled round aluminum wires of class 200. This standard, aligned with IEC 60317-89:2023, covers wires with a polyesterimide resin coating, which can be modified if the core chemical identity is maintained and all performance standards are met. The wire grades addressed are:
- Grade 1: Nominal diameters from 0.250 mm to 1.600 mm
- Grade 2: Nominal diameters from 0.250 mm to 5.000 mm
These enamelled aluminum wires are key in electrical applications requiring reliable insulation and thermal endurance. The standard incorporates requirements and test methods to ensure quality and uniformity.
Key Topics
Polyesterimide Enameled Wire Requirements
- Thermal Class 200: The wires must have a minimum temperature index of 200 and withstand a heat shock temperature of at least 220 °C.
- Wire Dimensions: Specific nominal conductor diameters are referenced and must comply with IEC 60317-0-3:2008 and amendments.
- Electrical Resistance: Ensures suitability for electrical applications by referencing established test procedures.
- Mechanical Properties: Tests for elongation, flexibility, adherence, and resistance to abrasion (as outlined in Table 1 of the standard) to guarantee durability during production and operation.
- Chemical Resistance: Includes solvent resistance and hydrolysis tests conforming to IEC 60851-4:2016 requirements.
- Insulation Integrity: Requirements for breakdown voltage, continuity of insulation, and pinhole testing help prevent insulation failures.
Wire Coating Modification
- The use of modified polyesterimide resins is permitted if they enhance performance but maintain the required chemical identity and compliance.
Testing Methods
- The standard is to be used with IEC 60317-0-3, including amendments from 2013 and 2019, ensuring harmonization of dimensional, physical, and electrical parameters.
Applications
Polyesterimide enameled round aluminum wires specified by SIST EN IEC 60317-89:2024 are used extensively in:
- Electric Motors: For manufacturing stator and rotor windings, benefiting from high thermal performance and chemical resistance.
- Transformers: Ensuring reliable coil insulation for both small and medium-sized power transformers and enabling efficient energy transfer.
- Generators: Used in winding applications due to their robust insulation properties and ability to withstand elevated temperatures.
- Inductors and Coils: In electrical and electronic devices, where space-saving and performance at high temperatures are required.
- Automotive and Appliance Components: In high-efficiency motors and compact devices needing durable, heat-resistant windings.
The wide range of conductor diameters makes these wires suitable for both precision electronics and heavy-duty equipment.
Related Standards
For comprehensive wire selection and testing, consult these relevant standards:
- IEC 60317-0-3: General requirements for enameled round aluminum wire - provides foundational dimensional and test criteria.
- IEC 60851 (all parts): Describes various test methods for winding wires, including chemical properties, resistance, and flexibility.
- IEC 60264 (series): Sets guidelines for packaging of winding wires to ensure safe transport and storage.
These related standards, together with SIST EN IEC 60317-89:2024, form the basis for quality assurance and international compatibility in winding wire specification and application.
Keywords: SIST EN IEC 60317-89:2024, polyesterimide enameled round aluminum wire, class 200, winding wire specifications, IEC 60317-89:2023, electrical insulation, thermal class 200, mechanical properties, transformer winding wire, enamelled aluminum wire standard.
Get Certified
Connect with accredited certification bodies for this standard
Element Materials Technology
Materials testing and product certification.
IMQ S.p.A. (Certification)
Italian electrical product certification.
SLG Prüf- und Zertifizierungs GmbH
German testing and certification body.
Sponsored listings
Frequently Asked Questions
SIST EN IEC 60317-89:2024 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Specifications for particular types of winding wires - Part 89: Polyesterimide enameled round aluminum wire, class 200 (IEC 60317-89:2023)". This standard covers: IEC 60317-89:2023 specifies the requirements of enamelled round aluminium winding wire of class 200 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,250 mm up to and including 1,600 mm; grade 2: 0,250 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and IEC 60317-0-3:2008/AMD1:2013. This International Standard is to be used in conjunction with IEC 60317-0-3:2008, its Amendment 1 (2013) and its Amendment 2 (2019).
IEC 60317-89:2023 specifies the requirements of enamelled round aluminium winding wire of class 200 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,250 mm up to and including 1,600 mm; grade 2: 0,250 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and IEC 60317-0-3:2008/AMD1:2013. This International Standard is to be used in conjunction with IEC 60317-0-3:2008, its Amendment 1 (2013) and its Amendment 2 (2019).
SIST EN IEC 60317-89:2024 is classified under the following ICS (International Classification for Standards) categories: 29.060.10 - Wires; 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN IEC 60317-89:2024 has the following relationships with other standards: It is inter standard links to SIST EN 60317-0-3:2008/A2:2019, SIST EN 60851-4:2016, SIST EN 60317-0-3:2008, SIST EN 60317-0-3:2008/A1:2014. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN IEC 60317-89:2024 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2024
Specifikacije za posebne vrste navijalnih žic - 89. del: Okrogla aluminijeva žica,
lakirana s poliesterimidnim lakom, razred 200 (IEC 60317-89:2023)
Specifications for particular types of winding wires - Part 89: Polyesterimide enameled
round aluminum wire, class 200 (IEC 60317-89:2023)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten Teil 89:
Runddrähte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 200 (IEC 60317-
89:2023)
Spécifications pour types particuliers de fils de bobinage - Partie 89: Fil de section
circulaire en aluminium émaillé au polyestérimide, classe 200 (IEC 60317-89:2023)
Ta slovenski standard je istoveten z: EN IEC 60317-89:2023
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60317-89
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2023
ICS 29.060.10
English Version
Specifications for particular types of winding wires - Part 89:
Polyesterimide enamelled round aluminum wire, class 200
(IEC 60317-89:2023)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 89: Fil de section circulaire en aluminium émaillé au Wickeldrähten Teil 89: Runddrähte aus Aluminium,
polyestérimide, classe 200 lackisoliert mit Polyesterimid, Klasse 200
(IEC 60317-89:2023) (IEC 60317-89:2023)
This European Standard was approved by CENELEC on 2023-09-04. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-89:2023 E
European foreword
The text of document 55/1939/CDV, future edition 1 of IEC 60317-89, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-06-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-09-04
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60317-89:2023 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60264 (series) NOTE Approved as EN 60264 (series)
IEC 60317 (series) NOTE Approved as EN 60317 (series)
IEC 60851 (series) NOTE Approved as EN 60851 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60317-0-3 2008 Specifications for particular types of winding EN 60317-0-3 2008
wires - Part 0-3: General requirements -
Enamelled round aluminium wire
+ A1 2013 + A1 2013
+ A2 2019 + A2 2019
IEC 60851-4 2016 Winding wires - Test methods - Part 4: EN 60851-4 2016
Chemical properties
IEC 60317-89 ®
Edition 1.0 2023-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 89: Polyesterimide enamelled round aluminum wire, class 200
Spécifications pour types particuliers de fils de bobinage –
Partie 89: Fil de section circulaire en aluminium émaillé au polyestérimide,
classe 200
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-7303-6
– 2 – IEC 60317-89:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 9
15 Temperature index . 9
16 Resistance to refrigerants . 9
17 Solderability . 9
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to hydrolysis and to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Resistance to abrasion . 8
IEC 60317-89:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES
...