oSIST prEN 16568:2026

SLOVENSKI STANDARD
01-december-2026
Goriva za motorna vozila - Metilni estri maščobnih kislin (FAME) goriv in mešanic z
dizelskim gorivom - Določanje oksidacijske stabilnosti z metodo pospešene
oksidacije pri 120 °C
Automotive fuels - Blends of Fatty acid methyl ester (FAME) with diesel fuel -
Determination of oxidation stability by rapidly accelerated oxidation method at 120 °C
Kraftstoffe - Mischungen von Fettsäure-Methylestern (FAME) mit Dieselkraftstoff -
Bestimmung der Oxidationsstabilität mittels stark beschleunigtem Oxidationsverfahren
bei 120 °C
Carburants pour automobiles - Mélanges d'esters méthyliques d'acides gras (EMAG)
avec du gazole - Détermination de la stabilité à l'oxydation par méthode d'oxydation plus
accélérée à 120 °C
Ta slovenski standard je istoveten z: prEN 16568
ICS:
75.160.20 Tekoča goriva Liquid fuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2026
ICS Will supersede EN 16568:2023
English Version
Automotive fuels - Fatty acid methyl ester (FAME) fuel and
blends with diesel fuel - Determination of oxidation
stability by rapidly accelerated oxidation method at 120 °C
Carburants pour automobiles - Esters méthyliques d' Kraftstoffe für Kraftfahrzeuge - Fettsäuremethylester
acides gras (EMAG) et mélanges avec du gazole - (FAME) Kraftstoff und Mischungen mit Dieselkraftstoff
Détermination de la stabilité à l'oxydation par méthode - Bestimmung der Oxidationsstabilität mittels stark
d'oxydation plus accélérée à 120 °C beschleunigtem Oxidationsverfahren bei 120 °C
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 19.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye
and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
C O M I T É E U R O P É E N D E N O R M A L I S A T I O N
E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16568 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Reagents and materials . 6
6 Apparatus . 6
6.1.1 Air filter . 9
6.1.2 Gas membrane pump . 9
6.1.3 Reaction vessel . 9
6.1.4 Closed measurement cell . 9
6.1.5 Electrodes . 9
6.1.6 Measuring and recording apparatus . 9
6.1.7 Contact thermometer graduated in 0,1 °C or Pt 100 element . 9
6.1.8 Heating block . 9
6.1.9 Standard laboratory PC, equipped with software for measurement and data
evaluation . 9
7 Sampling . 10
8 Preparation of measurement . 10
8.1 Preparation of test sample . 10
8.2 Preparation of the apparatus . 10
8.2.1 Cleaning procedure . 10
8.2.2 Temperature correction . 11
9 Measurement . 11
10 Calculation and evaluation . 14
10.1 Automatic evaluation . 14
10.2 Manual evaluation . 14
11 Expression of results . 15
12 Precision . 15
12.1 General . 15
12.2 Repeatability, r . 15
12.3 Reproducibility, R . 15
13 Test report . 15
Bibliography . 17
European foreword
This document (prEN 16568:2026) has been prepared by Technical Committee CEN/TC 19 “Gaseous
and liquid fuels, lubricants and related products of petroleum, synthetic and biological origin”, the
secretariat of which is held by NEN.
This document will supersede EN 16568:2023.
— extension of the scope from blends of fatty acid methyl ester with diesel fuel to neat FAME
— introduction of additional precision data for neat FAME
— alignment with the revised EN 15751 [1] .
Introduction
This document is based on EN 15751 [1], which was specifically developed for the determination of the
oxidation stability of neat fatty acid methyl esters (FAME) and blends with diesel fuel. The oxidation
stability is assessed by determining the induction period of the fuel. The induction period is a measure
for the ageing reserve of the fuel.
The first version of EN 15751 [1] was developed under CEN/TC 19 for a test temperature of 110 °C in
order to stay directly comparable to EN 14112 [2] which is used to determine the oxidation stability of
neat FAME. The stability of diesel/FAME blends is generally higher compared to neat FAME, thus leading
to long measuring times. To better accommodate the needs of laboratories, the reaction temperature
was raised to 120 °C. Degradation of the ageing reserve of the fuel follows the Arrhenius law. By
increasing the temperature by 10 °C, the reaction rate is doubled, cutting in half the induction period.
The modifications introduced into EN 16568:2014 [3] relative to EN 15751 [1] were restricted to diesel
fuel blends containing a volume fraction of FAME in the range of 2 % to 50 %. Neat FAME was not
included in the scope. Not enough adequate data was available showing that the ability is sufficient to
differentiate between different qualities of neat FAME when the induction period is reduced by 50 %.
Hence, a new validation was required to cover neat FAME. In 2024, an Inter-Laboratory Study (ILS) was
organized, executed by CEN/TC 19/JWG 1 (Vegetable fats and oils and their by-products for use in
automotive fuels, Joint working group with CEN/TC 307) in cooperation with CEN/TC 19/WG 44 (FAME
fuel developments) and CEN/ TC 19/WG 36 (Precision evaluation). The results obtained confirmed that
EN 16568 [4] at 120 °C is suitable for measuring the oxidation stability of neat FAME with a precision
that is in the same range as that determined for EN 15751 [1].
While developing the specification for paraffinic diesel fuel, three labs executed a small test on neat
paraffinic diesel and on 7 % FAME blends based on products originating from both Fischer-Tropsch
synthesis and hydrotreatment process. As no indications towards a different interaction were found
when EN 15751 [1] was applied, it was concluded that the stability of paraffinic diesel fuels can be
determined by the induction period. With respect to EN 16568 [4] , no verification at 120 °C was
performed, leaving the applicability of EN 16568 [4] to paraffinic diesel and FAME blends likely but
unconfirmed.
1 Scope
This document specifies a test method for the determination of the oxidation stability at 120 °C of fuels
for diesel engines, by means of measuring the induction period of the fuel. Two different areas of
application with separate precision statements are covered. For diesel fuel having a FAME content in
the range between 2 % and 50 %, an induction period of up to 20 hours can be determined. For neat
FAME, the maximum induction period is limited to 12 hours. The precision of the test method has been
developed for petroleum-based diesel originating from conventional sources.
This test method is applicable for FAME blends with paraffinic diesel fuels as specified in EN 15940
[5], however, precision has not been determined for this type of fuel.
NOTE 1 An almost identical test method for oxidation stability at 110 °C is described in EN 15751 [1] , which
applies to neat FAME and diesel/FAME blends containing 2 % of FAME at minimum. Other alternative test methods
for the determination of the oxidation stability of distillate fuels are described in CEN/TR 17225 [6].
NOTE 2 The precision of this method was determined by two studies using samples of diesel fuel blends with
FAME displaying a maximum induction period of approximately 20 h, respectively of neat FAME with a maximum
induction period of 12 hours. Higher induction periods are not covered by the precision statement; however,
experience from EN 15751 [1] indicates that this method can be used to determine induction periods up to 48 h.
NOTE 3 The presence of cetane improver can reduce the oxidation stability determined by this test method.
Limited studies with 2-ethyl hexyl nitrate (EHN) indicated that the stability is reduced to an extent which is within
the reproducibility of the test method.
NOTE 4 For the purposes of this document, percentages referring to FAME or other fuel content blends (e.g.
"FAME content in the range of 2 % to 50 %"), are volume fractions unless otherwise specified.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 3170, Hydrocarbon Liquids - Manual Sampling (ISO 3170:2025)
EN ISO 3171, Petroleum liquids - Automatic pipeline sampling (ISO 3171:1988)
EN ISO 3696, Water for analytical laboratory use - Specification and test methods (ISO 3696:1987)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
• ISO Online browsing platform: available at http://www.iso.org/obp
• IEC Electropedia: available at http://www.electropedia.org/
3.1
induction period
time which passes between the moment when the measurement is started and the moment when the
formation of oxidation products begins to increase rapidly
3.2
oxidation stability
induction period determined in accordance with the procedure specified in this document
4 Principle
A stream of purified air is passed through the sample which has been heated to the specified, elevated
temperature. Volatile compounds are formed during the oxidation process. They are passed, together
with the air, into a measurement cell containing demineralized or distilled water and equipped with a
conductivity electrode. The electrode is connected to a measuring and recording device. It indicates the
end of the induction period by rapid increase of the conductivity due to the dissociation of volatile
carboxylic acids produced during the oxidation process and absorbed in the water. For more details on
the background of the method see CEN/TR 17225 [6].
5 Reagents and materials
5.1 Distilled or demineralized water, conforming to EN ISO 3696.
5.2 Alkaline laboratory glass cleaning solution.
5.3 Ternary solvent mixture, 1 + 1 + 1 (by volume), consisting of methanol/toluene/acetone, each
of recognized analytical grade.
5.4 2-Propanol, of recognized analytical grade.
5.5 Thermo-stable oil, e.g. silicon oil.
6 Apparatus
6.1 Device for the determination of oxidation stability, consisting of the following parts (see
Figure 1 and Figure 2).
NOTE An instrument for determining the oxidation stability is commercially available under the trade name
Rancimat® (model 743 or higher) or OSI® Instrument.
Key
1 air filter 6.1.1
Rancimat® is a trademark of Metrohm AG, Herisau, Switzerland and OSI® Instrument is a trademark from
Omnion Inc., Rockland, Massachusetts, USA. This information is given for the convenience of users of this document
and does not constitute an endorsement by CEN of the products named. Equivalent devices may be used if they
can be shown to lead to the same results, at the same or better precision.
...