SIST EN 302 065-4-4 V1.1.1:2022
(Main)Short Range Devices (SRD) using Ultra Wide Band technology (UWB) - Harmonised Standard for access to radio spectrum - Part 4: Material Sensing devices - Sub-part 4 - Exterior material sensing applications for ground based vehicles
Short Range Devices (SRD) using Ultra Wide Band technology (UWB) - Harmonised Standard for access to radio spectrum - Part 4: Material Sensing devices - Sub-part 4 - Exterior material sensing applications for ground based vehicles
The present document specifies the requirements for technical characteristics and methods of measurements for material
sensing applications using UWB technology for external material sensing applications for ground-based vehicles.
The present document only covers non-contact based UWB material sensing devices according to ECC/DEC(07)01 [i.1]
and Commission Decision 2019/785/EU [i.2].
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB) tehnologijo - Harmonizirani standard za dostop do radijskega spektra - 4. del: Zaznavala snovi - 4. poddel: Naprave za zaznavanje zunanjih materialov za talna vozila
Ta dokument določa zahteve za tehnične lastnosti in merilne metode za zaznavala snovi z uporabo ultra širokopasovne (UWB) tehnologije za naprave za zaznavanje zunanjih materialov za talna vozila.
Dokument zajema samo zaznavala snovi, ki uporabljajo brezstično ultra širokopasovno tehnologijo v skladu z določili ECC/DEC(07)01 [i.1] in sklepom Komisije 2019/785/EU [i.2].
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.3] je podano v dodatku A.
General Information
Standards Content (Sample)
Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications for
ground based vehicles
2 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
3 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 EUT categories . 10
4.2.1 General . 10
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 11
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 12
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 13
4.3.3.3.1 EUT without any active mitigation techniques . 13
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 15
4.3.5 Total Radiated Power (TRP) . 15
4.3.5.1 Applicability. 15
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques. . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 16
4.3.6 Listen Before Talk (LBT) . 16
4.3.6.1 Applicability. 16
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 17
ETSI
4 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 19
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 General conditions for testing .
...
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications
for ground based vehicles
2 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
3 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 EUT categories . 11
4.2.1 General . 11
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 12
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 13
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 14
4.3.3.3.1 EUT without any active mitigation techniques . 14
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 16
4.3.5 Total Radiated Power (TRP) . 16
4.3.5.1 Applicability. 16
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 17
4.3.6 Listen Before Talk (LBT) . 17
4.3.6.1 Applicability. 17
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 18
ETSI
4 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 20
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing .
...
SLOVENSKI STANDARD
01-september-2022
Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB)
tehnologijo - Harmonizirani standard za dostop do radijskega spektra - 4. del:
Zaznavala snovi - 4. poddel: Naprave za zaznavanje zunanjih materialov za talna
vozila
Short Range Devices (SRD) using Ultra Wide Band technology (UWB) - Harmonised
Standard for access to radio spectrum - Part 4: Material Sensing devices - Sub-part 4 -
Exterior material sensing applications for ground based vehicles
Ta slovenski standard je istoveten z: ETSI EN 302 065-4-4 V1.1.1 (2022-06)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications
for ground based vehicles
2 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
3 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 EUT categories . 11
4.2.1 General . 11
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 12
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 13
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 14
4.3.3.3.1 EUT without any active mitigation techniques . 14
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 16
4.3.5 Total Radiated Power (TRP) . 16
4.3.5.1 Applicability. 16
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 17
4.3.6 Listen Before Talk (LBT) . 17
4.3.6.1 Applicability. 17
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 18
ETSI
4 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.