SIST EN 60357:2004/A3:2011
(Amendment)Tungsten halogen lamps (non-vehicle) - Performance specifications (IEC 60357:2002/A3:2011)
Tungsten halogen lamps (non-vehicle) - Performance specifications (IEC 60357:2002/A3:2011)
Amandma A3:2011 je dodatek k standardu SIST EN 60357:2004.
This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications:
- Projection (including cinematograph and still projection)
- Photographic (including studio)
- Floodlighting
- Special purpose
- General purpose
- Stage lighting
For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing.
NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample, submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible.
It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.
Halogen-Glühlampen (Fahrzeuglampen ausgenommen) - Anforderungen an die Arbeitsweise (IEC 60357:2002/A3:2011)
Lampes tungstène-halogène (véhicules exceptés) - Prescriptions de performances (CEI 60357:2002/A3:2011)
Volframove halogenske sijalke (ne za vozila) - Tehnične specifikacije - Dopolnilo A3 (IEC 60357:2002/A3:2011)
Amandma A3:2011 je dodatek k standardu SIST EN 60357:2004.
Ta mednarodni standard določa zahteve delovanja za volframove halogenske sijalke z enim ali dvema vznožkoma, ki imajo ocenjene napetosti do 250 V in so namenjene naslednji uporabi:
- projekciji (vključno s filmsko in nepremično projekcijo);
- fotografiji (vključno s studijsko);
- reflektorjem;
- posebnim namenom;
- splošnim namenom;
- razsvetljavi odra.
Za nekatere zahteve, podane v tem standardu, je podana referenca do »pomembnih tehničnih podatkov«. Za nekatere sijalke so ti tehnični podatki navedeni v tem standardu. Za druge sijalke na področja uporabe tega standarda je pomembne podatke podal proizvajalec sijalk ali odgovorni prodajalec. Zahteve tega standarda se nanašajo samo na tipsko preskušanje.
OPOMBA: Zahteve in tolerance, ki jih dovoljuje ta standard, ustrezajo preskušanju tipskega preskusnega vzorca, ki ga za ta namen predloži proizvajalec. Načelno mora biti ta tipski preskusni vzorec sestavljen iz enot, ki imajo lastnosti, značilne za proizvajalčevo proizvodnjo, in so, kolikor je le mogoče, blizu vrednostim osrednje točke proizvodnje.
Lahko pričakujemo, da bodo ob tolerancah, podanih v tem standardu, proizvodi proizvedeni v skladu s tipskim preskusnim vzorcem ustrezali standardu za večino proizvodnje. Zaradi širjenja proizvodnje je neizogibno, da so včasih proizvodi zunaj določenih toleranc. Za smernice pri vzorčnih načrtih in postopkih za pregled po atributih glej IEC 60410.
General Information
- Status
- Published
- Publication Date
- 09-May-2011
- Technical Committee
- IESV - Lamps and related equipment
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 26-Apr-2011
- Due Date
- 01-Jul-2011
- Completion Date
- 10-May-2011
Relations
- Effective Date
- 01-Jun-2011
Overview
SIST EN 60357:2004/A3:2011 is an international standard that specifies performance requirements for tungsten halogen lamps, excluding those intended for vehicle applications. This amendment (A3:2011) updates and supplements the European Standard EN 60357:2003 (equivalent to IEC 60357:2002/A3:2011). The standard covers single-capped and double-capped tungsten halogen lamps with rated voltages up to 250 V, defining key performance criteria relevant for a wide range of professional and general-purpose lighting applications.
By establishing a set of clear and harmonized performance specifications, this standard helps manufacturers, vendors, and users ensure consistent lamp quality and suitability for demanding applications such as projection, studio work, and specialized lighting environments.
Key Topics
- Performance Specifications: Defines requirements for luminous output, rated wattage, rated voltage, and lamp-operating characteristics.
- Product Scope: Applies to a full spectrum of tungsten halogen lamps used in:
- Projection (cinematographic and still)
- Photographic (studio and general photography)
- Floodlighting
- Special and general-purpose lighting
- Stage and theater lighting
- Reference Data Sheets: Some lamp types are detailed within the standard via specific data sheets. For other types within the standard’s scope, the manufacturer or vendor provides the key specifications.
- Type Testing Only: The requirements pertain exclusively to type testing of representative samples, not to every unit produced.
- Production Tolerances: Acknowledges permissible manufacturing variances, aiming for the majority of production within specified limits.
- Sampling Guidance: For inspection and sampling methodology, the standard refers to IEC 60410 on attribute inspection procedures.
Applications
Tungsten halogen lamps standardized by SIST EN 60357:2004/A3:2011 are essential in various fields where precise, high-quality illumination is required:
- Projection and Cinematography: Reliable performance is vital for consistent light output in projectors, film, and slide displays.
- Photography and Studio Lighting: Ensures stable color temperature and bright, flicker-free operation, ideal for studio sets and photographic environments.
- Floodlighting: Provides robust, high-output lighting suited for large areas, exhibitions, or outdoor events.
- Stage and Theater Lighting: Detailed performance specifications support creative lighting effects and help meet the rigorous demands of performance venues.
- Special Applications: Supports various fields, from scientific instrumentation to architectural feature lighting, where lamp reliability and consistent output are priorities.
- General Purpose Use: Fully compatible with general non-vehicle lighting needs, ensuring safety and efficiency.
By adhering to this standard, users benefit from dependable quality, predictable performance, and compatibility with lighting systems designed for specified lamp types.
Related Standards
- IEC 60357: The foundational international standard for tungsten halogen lamp performance.
- EN 60357: European adoption of the IEC standard, aligned with regional requirements.
- IEC 60410: Provides procedures for sampling plans and attribute inspections referenced for production and compliance verification.
- IEC 60061-1: Specifies lamp caps and holders, relevant for ensuring physical compatibility and safety.
Keywords: tungsten halogen lamps, performance specifications, projection lighting, stage lighting, photographic lighting, non-vehicle lamps, lamp standards, IEC 60357, EN 60357, type testing, SIST, quality assurance.
By implementing SIST EN 60357:2004/A3:2011, organizations and manufacturers can ensure their tungsten halogen lamps consistently meet industry-accepted benchmarks for performance, safety, and quality.
Get Certified
Connect with accredited certification bodies for this standard
IMQ S.p.A. (Certification)
Italian electrical product certification.
SLG Prüf- und Zertifizierungs GmbH
German testing and certification body.
UL Solutions
Global safety science company with testing, inspection and certification.
Sponsored listings
Frequently Asked Questions
SIST EN 60357:2004/A3:2011 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Tungsten halogen lamps (non-vehicle) - Performance specifications (IEC 60357:2002/A3:2011)". This standard covers: Amandma A3:2011 je dodatek k standardu SIST EN 60357:2004. This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: - Projection (including cinematograph and still projection) - Photographic (including studio) - Floodlighting - Special purpose - General purpose - Stage lighting For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample, submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.
Amandma A3:2011 je dodatek k standardu SIST EN 60357:2004. This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: - Projection (including cinematograph and still projection) - Photographic (including studio) - Floodlighting - Special purpose - General purpose - Stage lighting For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample, submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.
SIST EN 60357:2004/A3:2011 is classified under the following ICS (International Classification for Standards) categories: 29.140.20 - Incandescent lamps. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 60357:2004/A3:2011 has the following relationships with other standards: It is inter standard links to SIST EN 60357:2004. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 60357:2004/A3:2011 is associated with the following European legislation: EU Directives/Regulations: 1194/2012, 244/2009, 874/2012; Standardization Mandates: M/495 AMD 3, M/495 AMD 3. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 60357:2004/A3:2011 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2011
9ROIUDPRYHKDORJHQVNHVLMDONH QH]DYR]LOD 7HKQLþQHVSHFLILNDFLMH'RSROQLOR
$ ,(& $
Tungsten halogen lamps (non-vehicle) - Performance specifications (IEC
60357:2002/A3:2011)
Halogen-Glühlampen (Fahrzeuglampen ausgenommen) - Anforderungen an die
Arbeitsweise (IEC 60357:2002/A3:2011)
Lampes tungstène-halogène (véhicules exceptés) - Prescriptions de performances (CEI
60357:2002/A3:2011)
Ta slovenski standard je istoveten z: EN 60357:2003/A3:2011
ICS:
29.140.20 Žarnice z žarilno nitko Incandescent lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60357/A3
NORME EUROPÉENNE
April 2011
EUROPÄISCHE NORM
ICS 29.140.20
English version
Tungsten halogen lamps (non-vehicle) -
Performance specifications
(IEC 60357:2002/A3:2011)
Lampes tungstène-halogène (véhicules Halogen-Glühlampen (Fahrzeuglampen
exceptés) - ausgenommen) -
Prescriptions de performances Anforderungen an die Arbeitsweise
(CEI 60357:2002/A3:2011) (IEC 60357:2002/A3:2011)
This amendment A3 modifies the European Standard EN 60357:2003; it was approved by CENELEC on
2011-03-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60357:2003/A3:2011 E
Foreword
The text of document 34A/1394/CDV, future amendment 3 to IEC 60357:2002, prepared by SC 34A,
Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as amendment A3 to EN 60357:2003 on 2011-03-03.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
(dop) 2011-12-03
an identical national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-03-03
with the amendment have to be withdrawn
__________
Endorsement notice
The text of amendment 3:2011 to the International Standard IEC 60357:2002 was approved by
CENELEC as an amendment to the European Standard without any modification.
__________
IEC 60357
Edition 3.0 2011-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 3
AMENDEMENT 3
The sheets contained in this amendment are to be inserted in IEC 60357
Les feuilles de cet amendement sont à insérer dans la CEI 60357
Tungsten halogen lamps (non-vehicle) – Performance specifications
Lampes tungstène-halogène (véhicules exceptés) – Prescriptions de
performances
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX E
ICS 29.140.20 ISBN 978-2-88912-332-2
60357 Amend. 3 © IEC:2011
FOREWORD
This amendment has been prepared by subcommittee 34A: Lamps, of IEC technical committee
34: Lamps and related equipment.
The text of this amendment is based on the following documents:
CDV Report on voting
34A/1394/CDV 34A/1437/RVC
Full information on the voting for the approval of this amendment can be found in t
...