SIST EN 301 908-13 V13.1.1:2020
(Main)IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
The present document applies to the following radio equipment type:
• User Equipment for Evolved Universal Terrestrial Radio Access (E-UTRA).
This radio equipment type is capable of operating in all or any part of the frequency bands given in tables from 1-1 through 1-5.
Table 1-1: E-UTRA UE operating bands
NOTE 1: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.2] is given in annex A.
Table 1-1A: Sub-bands for band 46
Table 1-2: E-UTRA UE Intra-band contiguous CA operating bands
Table 1-3: E-UTRA UE Inter-band CA operating bands (two bands)
Table 1-4: E-UTRA UE Inter-band CA operating bands (three bands)
Table 1-5: Intra-band non-contiguous CA operating bands (with two sub-blocks)
E-UTRA NB-IoT is designed to operate in the E-UTRA operating bands 1, 3, 8, 20, 28 and 65 defined in table 1-1. The present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP™ Releases 8, 9, 10, 11, 12, and 13 defined in ETSI TS 136 101 [3]. This includes the requirements for E-UTRA UE operating bands and E-UTRA CA operating bands from 3GPP™ Release 13 defined in ETSI TS 136 101 [3].
NOTE 2: For Band 20: For user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (total radiated power), as described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. For user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra - 13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)
Ta dokument se uporablja za radijsko opremo naslednje vrste:
• uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA).
Ta vrsta radijske opreme lahko deluje v vseh delih frekvenčnih pasov iz preglednic od 1-1 do 1-5.
Preglednica 1-1: Operativni pasovi E-UTRA UE
OPOMBA 1: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.2] je podano v dodatku A.
Preglednica 1-1A: Podpasovi za pas 46
Preglednica 1-2: Medpasovno združevanje soležnih operativnih pasov CA E-UTRA UE
Preglednica 1-3: Medpasovno združevanje operativnih pasov CA E-UTRA UE (dva pasova)
Preglednica 1-4: Medpasovno združevanje operativnih pasov CA E-UTRA UE (trije pasovi)
Preglednica 1-5: Medpasovno združevanje nesoležnih operativnih pasov CA (z dvema podblokoma)
E-UTRA NB-IoT je zasnovan za delovanje v operativnih pasovih E-UTRA 1, 3, 8, 20, 28 in 65, ki so opredeljeni v preglednici 1-1. Ta dokument zajema zahteve za uporabniško opremo E-UTRA FDD in E-UTRA TDD iz izdaj 8, 9, 10, 11, 12 in 13 dokumenta 3GPP™, kot je opredeljeno v dokumentu ETSI TS 136 101 [3]. To vključuje zahteve za operativne pasove E-UTRA UE in operativne pasove CA E-UTRA iz izdaje 13 dokumenta 3GPP™, kot je opredeljeno v dokumentu ETSI TS 136 101 [3].
OPOMBA 2: Za pas 20: Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.6] in Sklepu Odbora za elektronske komunikacije (09)03 [i.7]. Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.6] in Sklepu Odbora za elektronske komunikacije (09)03 [i.7]. Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj.
General Information
- Status
- Published
- Public Enquiry End Date
- 24-Nov-2019
- Publication Date
- 14-Jan-2020
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 12-Dec-2019
- Due Date
- 16-Feb-2020
- Completion Date
- 15-Jan-2020
- Directive
- Harmonized Standard2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/ECOJ Ref: L 289 (DATUM UMIKA Z DNEM 10.5.2024)
Buy Documents
ETSI EN 301 908-13 V13.0.1 (2019-08) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
ETSI EN 301 908-13 V13.1.1 (2019-11) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
Overview
SIST EN 301 908-13 V13.1.1:2020 is a harmonised European standard developed by SIST for IMT cellular networks, specifically focusing on Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE). This standard ensures that user equipment (typically mobile devices) used in LTE and LTE-Advanced networks can access and use radio spectrum efficiently, fulfilling regulatory and technical requirements under the Radio Equipment Directive (2014/53/EU).
The standard applies to E-UTRA UE operating across multiple frequency bands, supporting legacy and advanced cellular technologies as specified by 3GPP Releases 8-13. It addresses key compliance aspects for UE, such as transmitter and receiver performance, spectrum emission, and carrier aggregation operations. The document guarantees that radio equipment avoids causing harmful interference and promotes the efficient use of the radio spectrum across Europe.
Key Topics
SIST EN 301 908-13 V13.1.1:2020 covers a comprehensive range of technical and regulatory topics for E-UTRA UEs, including:
- Operating Bands
- Defines supported frequency bands and carrier aggregation modes for E-UTRA UE, allowing operation in various markets and regions.
- Technical Requirements for Transmitters
- Output power limits (maximum/minimum)
- Spectrum emission masks
- Spurious emission controls
- Carrier aggregation (intra-band and inter-band, contiguous and non-contiguous)
- Technical Requirements for Receivers
- Adjacent Channel Selectivity (ACS)
- Blocking characteristics
- Spurious response and emissions
- Reference sensitivity levels
- Intermodulation performance
- Compliance with Essential Requirements
- Ensures conformity with Article 3.2 of the European Radio Equipment Directive (RED), referencing EU legislation and CEPT/ECC decisions.
- Testing and Conformance
- Defines test methods and criteria for verifying UE performance under challenging environmental and operational conditions.
Applications
This standard is essential for manufacturers, testing laboratories, and regulatory authorities involved in the development, certification, and market access of mobile devices within LTE/LTE-Advanced networks. Key applications include:
- Mobile Device Design and Certification
- Ensures that smartphones, tablets, and IoT modules comply with spectrum and radio performance requirements before market launch.
- Operator Network Deployment
- Supports quality of service and network reliability by specifying minimum receiver sensitivity, output power, and spectrum efficiency.
- Interoperability in Global Markets
- Facilitates cross-border trade by harmonising equipment requirements for multiple frequency bands and carrier aggregation schemes.
- IoT and M2M (Machine-to-Machine) Devices
- Supports NB-IoT operation in specific E-UTRA bands, enabling wide-area IoT connectivity for industrial and consumer applications.
- Regulatory Compliance and Market Access
- Provides a basis for demonstrating equipment compliance with EU legislation, streamlining approval processes and market entry.
Related Standards
Organizations involved in E-UTRA UE deployment should also be familiar with the following relevant standards:
- ETSI EN 301 908-1 - General requirements for IMT cellular network equipment
- ETSI TS 136 101 - 3GPP technical specification detailing E-UTRA and LTE requirements for UE
- SIST EN 301 908 Series - Comprehensive suite detailing requirements for various cellular technologies and equipment types
- Directive 2014/53/EU - Radio Equipment Directive (RED), foundation for essential requirements in Europe
- Commission Decision 2010/267/EU and ECC Decision (09)03 - Provide guidelines on spectrum usage and power requirements for mobile devices
SIST EN 301 908-13 V13.1.1:2020 is critical for ensuring that LTE user equipment meets harmonised European requirements, enabling reliable mobile communications and supporting the expanding mobile broadband and IoT ecosystems.
Buy Documents
ETSI EN 301 908-13 V13.0.1 (2019-08) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
ETSI EN 301 908-13 V13.1.1 (2019-11) - IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 301 908-13 V13.1.1:2020 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)". This standard covers: The present document applies to the following radio equipment type: • User Equipment for Evolved Universal Terrestrial Radio Access (E-UTRA). This radio equipment type is capable of operating in all or any part of the frequency bands given in tables from 1-1 through 1-5. Table 1-1: E-UTRA UE operating bands NOTE 1: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.2] is given in annex A. Table 1-1A: Sub-bands for band 46 Table 1-2: E-UTRA UE Intra-band contiguous CA operating bands Table 1-3: E-UTRA UE Inter-band CA operating bands (two bands) Table 1-4: E-UTRA UE Inter-band CA operating bands (three bands) Table 1-5: Intra-band non-contiguous CA operating bands (with two sub-blocks) E-UTRA NB-IoT is designed to operate in the E-UTRA operating bands 1, 3, 8, 20, 28 and 65 defined in table 1-1. The present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP™ Releases 8, 9, 10, 11, 12, and 13 defined in ETSI TS 136 101 [3]. This includes the requirements for E-UTRA UE operating bands and E-UTRA CA operating bands from 3GPP™ Release 13 defined in ETSI TS 136 101 [3]. NOTE 2: For Band 20: For user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (total radiated power), as described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. For user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.
The present document applies to the following radio equipment type: • User Equipment for Evolved Universal Terrestrial Radio Access (E-UTRA). This radio equipment type is capable of operating in all or any part of the frequency bands given in tables from 1-1 through 1-5. Table 1-1: E-UTRA UE operating bands NOTE 1: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.2] is given in annex A. Table 1-1A: Sub-bands for band 46 Table 1-2: E-UTRA UE Intra-band contiguous CA operating bands Table 1-3: E-UTRA UE Inter-band CA operating bands (two bands) Table 1-4: E-UTRA UE Inter-band CA operating bands (three bands) Table 1-5: Intra-band non-contiguous CA operating bands (with two sub-blocks) E-UTRA NB-IoT is designed to operate in the E-UTRA operating bands 1, 3, 8, 20, 28 and 65 defined in table 1-1. The present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP™ Releases 8, 9, 10, 11, 12, and 13 defined in ETSI TS 136 101 [3]. This includes the requirements for E-UTRA UE operating bands and E-UTRA CA operating bands from 3GPP™ Release 13 defined in ETSI TS 136 101 [3]. NOTE 2: For Band 20: For user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (total radiated power), as described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. For user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.
SIST EN 301 908-13 V13.1.1:2020 is classified under the following ICS (International Classification for Standards) categories: 33.060.99 - Other equipment for radiocommunications; 33.070.99 - Other mobile services. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 301 908-13 V13.1.1:2020 is associated with the following European legislation: EU Directives/Regulations: 2014/53/EU. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 301 908-13 V13.1.1:2020 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
2 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
Reference
REN/MSG-TFES-13-13
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 12
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 17
3.1 Terms . 17
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 33
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 33
4.2.3.3.1 Definition. 33
4.2.3.3.2 Limits . 33
4.2.3.3.3 Conformance . 33
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI
4 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 34
4.2.4 Transmitter Spurious Emissions . 34
4.2.4.1 Transmitter spurious emissions for Single Carrier . 34
4.2.4.1.1 Definition. 34
4.2.4.1.2 Limits . 34
4.2.4.1.3 Conformance . 38
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 38
4.2.4.2.1 Definition. 38
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 44
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 44
4.2.4.3.1 Definition. 44
4.2.4.3.2 Limits . 44
4.2.4.3.3 Conformance . 44
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 44
4.2.4.4.1 Definition. 44
4.2.4.4.2 Limits . 44
4.2.4.4.3 Conformance . 45
4.2.4.5 Transmitter spurious emissions for category NB1 . 45
4.2.4.5.1 Definition. 45
4.2.4.5.2 Limits . 45
4.2.4.5.3 Conformance . 45
4.2.5 Transmitter Minimum Output Power . 45
4.2.5.1 Transmitter minimum output power for Single Carrier. 45
4.2.5.1.1 Definition. 45
4.2.5.1.2 Limits . 45
4.2.5.1.3 Conformance . 45
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 46
4.2.5.2.1 Definition. 46
4.2.5.2.2 Limits . 46
4.2.5.2.3 Conformance . 46
4.2.5.3 Transmitter minimum output power for UL-MIMO . 46
4.2.5.3.1 Definition. 46
4.2.5.3.2 Limits . 46
4.2.5.3.3 Conformance . 47
4.2.5.4 Transmitter minimum output power for category NB1 . 47
4.2.5.4.1 Definition. 47
4.2.5.4.2 Limits . 47
4.2.5.4.3 Conformance . 47
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 47
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 47
4.2.6.1.1 Definition. 47
4.2.6.1.2 Limits . 47
4.2.6.1.3 Conformance . 48
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 48
4.2.6.2.1 Definition. 48
4.2.6.2.2 Limits . 49
4.2.6.2.3 Conformance . 49
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 50
4.2.6.3.1 Definition. 50
4.2.6.3.2 Limits . 50
4.2.6.3.3 Conformance . 50
4.2.7 Receiver Blocking Characteristics . 50
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 50
4.2.7.1.1 Definition. 50
4.2.7.1.2 Limits . 50
4.2.7.1.3 Conformance . 52
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 52
ETSI
5 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
4.2.7.2.1 Definition. 52
4.2.7.2.2 Limits . 53
4.2.7.2.3 Conformance . 55
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 56
4.2.7.3.1 Definition. 56
4.2.7.3.2 Limits . 56
4.2.7.3.3 Conformance . 57
4.2.8 Receiver Spurious Response . 57
4.2.8.1 Receiver Spurious Response for Single Carrier . 57
4.2.8.1.1 Definition. 57
4.2.8.1.2 Limits . 57
4.2.8.1.3 Conformance . 58
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 58
4.2.8.2.1 Definition. 58
4.2.8.2.2 Limits . 58
4.2.8.2.3 Conformance . 58
4.2.8.3 Receiver Spurious Response for category NB1 . 58
4.2.8.3.1 Definition. 58
4.2.8.3.2 Limits . 58
4.2.8.3.3 Conformance . 59
4.2.9 Receiver Intermodulation Characteristic . 59
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 59
4.2.9.1.1 Definition. 59
4.2.9.1.2 Limits . 59
4.2.9.1.3 Conformance . 59
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 60
4.2.9.2.1 Definition. 60
4.2.9.2.2 Limits . 60
4.2.9.2.3 Conformance . 60
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 60
4.2.9.3.1 Definition. 60
4.2.9.3.2 Limits . 61
4.2.9.3.3 Conformance . 61
4.2.10 Receiver Spurious Emissions . 61
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 61
4.2.10.1.1 Definition. 61
4.2.10.1.2 Limits . 61
4.2.10.1.3 Conformance . 61
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 61
4.2.10.2.1 Definition. 61
4.2.10.2.2 Limits . 62
4.2.10.2.3 Conformance . 62
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 62
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 62
4.2.11.1.1 Definition. 62
4.2.11.1.2 Limits . 62
4.2.11.1.3 Conformance . 63
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 63
4.2.11.2.1 Definition. 63
4.2.11.2.2 Limits for CA UTRA . 64
4.2.11.2.3 Limits for CA EUTRA . 65
4.2.11.2.4 Conformance . 65
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 65
4.2.11.3.1 Definition. 65
4.2.11.3.2 Limits . 66
4.2.11.3.3 Conformance . 67
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 67
4.2.11.4.1 Definition. 67
4.2.11.4.2 Limits . 67
4.2.11.4.3 Conformance . 67
4.2.11.5 Transmitter adjacent channel leakage power ratio for category NB1 . 67
ETSI
6 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
4.2.11.5.1 Definition. 67
4.2.11.5.2 Limits . 67
4.2.11.5.3 Conformance . 68
4.2.12 Receiver Reference Sensitivity Level . 68
4.2.12.0 General . 68
4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 68
4.2.12.1.1 Definition. 68
4.2.12.1.2 Limits . 68
4.2.12.1.3 Conformance . 68
4.2.12.2 Receiver Reference Sensitivity Level for Carrier Aggregation in DL-only bands . 69
4.2.12.2.1 Definition. 69
4.2.12.2.2 Limits . 69
4.2.12.2.3 Conformance . 70
4.2.12.3 Receiver Reference Sensitivity Level for category NB1 . 70
4.2.12.3.1 Definition. 70
4.2.12.3.2 Limits . 70
4.2.12.3.3 Conformance . 70
4.2.12.4 Receiver Reference Sensitivity Level for UE category 0 . 70
4.2.12.4.1 Definition. 70
4.2.12.4.2 Limits . 70
4.2.12.4.3 Conformance . 71
4.2.12.5 Receiver Reference Sensitivity Level for UE category M1 . 71
4.2.12.5.1 Definition. 71
4.2.12.5.2 Limits . 71
4.2.12.5.3 Conformance . 72
5 Testing for compliance with technical requirements . 73
5.1 Environmental conditions for testing . 73
5.2 Interpretation of the measurement results . 73
5.3 Essential radio test suites . 73
5.3.0 General . 73
5.3.1 Transmitter Maximum Output Power . 73
5.3.1.1 Transmitter maximum output power for Single Carrier . 73
5.3.1.1.1 Method of test . 73
5.3.1.1.2 Test requirements . 74
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 74
5.3.1.2.1 Method of test . 74
5.3.1.2.2 Test requirements . 75
5.3.1.2A Transmitter maximum output power for inter-band Carrier Aggregation (DL CA and UL CA) . 75
5.3.1.2A.1 Method of test . 75
5.3.1.2A.2 Test requirements . 76
5.3.1.3 Transmitter maximum output power for UL-MIMO . 76
5.3.1.3.1 Method of test . 76
5.3.1.3.2 Test requirements . 77
5.3.1.4 Transmitter maximum output power for category NB1 . 77
5.3.1.4.1 Method of Test . 77
5.3.1.4.2 Test requirements . 78
5.3.1.5 Transmitter maximum output power for UE category 0 . 78
5.3.1.5.1 Method of test . 78
5.3.1.5.2 Test requirements . 78
5.3.1.6 Transmitter maximum output power for UE category M1 . 78
5.3.1.6.1 Method of test . 78
5.3.1.6.2 Test requirements . 79
5.3.2 Transmitter Spectrum Emission Mask . 79
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 79
5.3.2.1.1 Method of test . 79
5.3.2.1.2 Test requirements . 80
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 80
5.3.2.2.1 Method of test . 80
5.3.2.2.2 Test requirements . 81
ETSI
7 Draft ETSI EN 301 908-13 V13.0.1 (2019-08)
5.3.2.2A Transmitter spectrum emission mask for inter-band Carrier Aggregation (DL CA and UL CA) . 81
5.3.2.2A.1 Method of test . 81
5.3.2.2A.2 Test requirements . 82
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 82
5.3.2.3.1 Method of test . 82
5.3.2.3.2 Test requirements . 83
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 83
5.3.2.4.1 Method of test . 83
5.3.2.4.2 Test requirements . 84
5.3.2.5 Transmitter spectrum emission mask for category NB1 . 84
5.3.2.5.1 Method of test . 84
5.3.2.5.2 Test requirements . 84
5.3.2.6 Transmitter spectrum emission mask for UE category 0 . 85
5.3.2.6.1 Method of test . 85
5.3.2.6.2 Test requirements . 85
5.3.2.7 Transmitter spectrum emission mask for UE category M1 . 85
5.3.2.7.1 Method of test . 85
5.3.2.7.2 Test requirements . 86
5.3.3 Transmitter Spurious Emissions . 86
5.3.3.1 Transmitter spurious emissions for Single Carrier . 86
5.3.3.1.1 Method of test . 86
5.3.3.1.2 Test requirements . 87
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 87
5.3.3.2.1 Method of test . 87
5.3.3.2.2 Test requirements . 88
5.3.3.2A Transmitter spurious emissions for inter-band Carrier Aggregation (DL CA and UL CA) . 88
5.3.3.2A.1 Method of test . 88
5.3.3.2A.2 Test requirements . 89
5.3.3.3 Transmitter spurious emissions for UL-MIMO . 89
5.3.3.3.1 Method of test . 89
5.3.3.3.2 Test requirements . 90
5.3.3.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 90
5.3.3.4.1 Method of test . 90
5.3.3.4.2 Test requirements .
...
ETSI EN 301 908-13 V13.1.1 (2019-11)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
2 ETSI EN 301 908-13 V13.1.1 (2019-11)
Reference
REN/MSG-TFES-13-13
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 908-13 V13.1.1 (2019-11)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 11
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 17
3.1 Terms . 17
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 33
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 33
4.2.3.3.1 Definition. 33
4.2.3.3.2 Limits . 33
4.2.3.3.3 Conformance . 33
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI
4 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 34
4.2.4 Transmitter Spurious Emissions . 34
4.2.4.1 Transmitter spurious emissions for Single Carrier . 34
4.2.4.1.1 Definition. 34
4.2.4.1.2 Limits . 34
4.2.4.1.3 Conformance . 38
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 38
4.2.4.2.1 Definition. 38
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 44
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 44
4.2.4.3.1 Definition. 44
4.2.4.3.2 Limits . 44
4.2.4.3.3 Conformance . 44
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 44
4.2.4.4.1 Definition. 44
4.2.4.4.2 Limits . 44
4.2.4.4.3 Conformance . 45
4.2.4.5 Transmitter spurious emissions for category NB1 . 45
4.2.4.5.1 Definition. 45
4.2.4.5.2 Limits . 45
4.2.4.5.3 Conformance . 45
4.2.5 Transmitter Minimum Output Power . 45
4.2.5.1 Transmitter minimum output power for Single Carrier. 45
4.2.5.1.1 Definition. 45
4.2.5.1.2 Limits . 45
4.2.5.1.3 Conformance . 45
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 46
4.2.5.2.1 Definition. 46
4.2.5.2.2 Limits . 46
4.2.5.2.3 Conformance . 46
4.2.5.3 Transmitter minimum output power for UL-MIMO . 46
4.2.5.3.1 Definition. 46
4.2.5.3.2 Limits . 46
4.2.5.3.3 Conformance . 47
4.2.5.4 Transmitter minimum output power for category NB1 . 47
4.2.5.4.1 Definition. 47
4.2.5.4.2 Limits . 47
4.2.5.4.3 Conformance . 47
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 47
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 47
4.2.6.1.1 Definition. 47
4.2.6.1.2 Limits . 47
4.2.6.1.3 Conformance . 48
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 48
4.2.6.2.1 Definition. 48
4.2.6.2.2 Limits . 49
4.2.6.2.3 Conformance . 49
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 50
4.2.6.3.1 Definition. 50
4.2.6.3.2 Limits . 50
4.2.6.3.3 Conformance . 50
4.2.7 Receiver Blocking Characteristics . 50
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 50
4.2.7.1.1 Definition. 50
4.2.7.1.2 Limits . 50
4.2.7.1.3 Conformance . 52
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 52
ETSI
5 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.7.2.1 Definition. 52
4.2.7.2.2 Limits . 53
4.2.7.2.3 Conformance . 55
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 56
4.2.7.3.1 Definition. 56
4.2.7.3.2 Limits . 56
4.2.7.3.3 Conformance . 57
4.2.8 Receiver Spurious Response . 57
4.2.8.1 Receiver Spurious Response for Single Carrier . 57
4.2.8.1.1 Definition. 57
4.2.8.1.2 Limits . 57
4.2.8.1.3 Conformance . 58
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 58
4.2.8.2.1 Definition. 58
4.2.8.2.2 Limits . 58
4.2.8.2.3 Conformance . 58
4.2.8.3 Receiver Spurious Response for category NB1 . 58
4.2.8.3.1 Definition. 58
4.2.8.3.2 Limits . 58
4.2.8.3.3 Conformance . 59
4.2.9 Receiver Intermodulation Characteristic . 59
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 59
4.2.9.1.1 Definition. 59
4.2.9.1.2 Limits . 59
4.2.9.1.3 Conformance . 59
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 60
4.2.9.2.1 Definition. 60
4.2.9.2.2 Limits . 60
4.2.9.2.3 Conformance . 60
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 60
4.2.9.3.1 Definition. 60
4.2.9.3.2 Limits . 61
4.2.9.3.3 Conformance . 61
4.2.10 Receiver Spurious Emissions . 61
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 61
4.2.10.1.1 Definition. 61
4.2.10.1.2 Limits . 61
4.2.10.1.3 Conformance . 61
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 61
4.2.10.2.1 Definition. 61
4.2.10.2.2 Limits . 62
4.2.10.2.3 Conformance . 62
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 62
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 62
4.2.11.1.1 Definition. 62
4.2.11.1.2 Limits . 62
4.2.11.1.3 Conformance . 63
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 63
4.2.11.2.1 Definition. 63
4.2.11.2.2 Limits for CA UTRA . 64
4.2.11.2.3 Limits for CA EUTRA . 65
4.2.11.2.4 Conformance . 65
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 65
4.2.11.3.1 Definition. 65
4.2.11.3.2 Limits . 66
4.2.11.3.3 Conformance . 67
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 67
4.2.11.4.1 Definition. 67
4.2.11.4.2 Limits . 67
4.2.11.4.3 Conformance . 67
4.2.11.5 Transmitter adjacent channel leakage power ratio for category NB1 . 67
ETSI
6 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.11.5.1 Definition. 67
4.2.11.5.2 Limits . 67
4.2.11.5.3 Conformance . 68
4.2.12 Receiver Reference Sensitivity Level . 68
4.2.12.0 General . 68
4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 68
4.2.12.1.1 Definition. 68
4.2.12.1.2 Limits . 68
4.2.12.1.3 Conformance . 68
4.2.12.2 Receiver Reference Sensitivity Level for Carrier Aggregation in DL-only bands . 69
4.2.12.2.1 Definition. 69
4.2.12.2.2 Limits . 69
4.2.12.2.3 Conformance . 70
4.2.12.3 Receiver Reference Sensitivity Level for category NB1 . 70
4.2.12.3.1 Definition. 70
4.2.12.3.2 Limits . 70
4.2.12.3.3 Conformance . 70
4.2.12.4 Receiver Reference Sensitivity Level for UE category 0 . 70
4.2.12.4.1 Definition. 70
4.2.12.4.2 Limits . 70
4.2.12.4.3 Conformance . 71
4.2.12.5 Receiver Reference Sensitivity Level for UE category M1 . 71
4.2.12.5.1 Definition. 71
4.2.12.5.2 Limits . 71
4.2.12.5.3 Conformance . 72
5 Testing for compliance with technical requirements . 73
5.1 Environmental conditions for testing . 73
5.2 Interpretation of the measurement results . 73
5.3 Essential radio test suites . 73
5.3.0 General . 73
5.3.1 Transmitter Maximum Output Power . 73
5.3.1.1 Transmitter maximum output power for Single Carrier . 73
5.3.1.1.1 Method of test . 73
5.3.1.1.2 Test requirements . 74
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 74
5.3.1.2.1 Method of test . 74
5.3.1.2.2 Test requirements . 75
5.3.1.2A Transmitter maximum output power for inter-band Carrier Aggregation (DL CA and UL CA) . 75
5.3.1.2A.1 Method of test . 75
5.3.1.2A.2 Test requirements . 76
5.3.1.3 Transmitter maximum output power for UL-MIMO . 76
5.3.1.3.1 Method of test . 76
5.3.1.3.2 Test requirements . 77
5.3.1.4 Transmitter maximum output power for category NB1 . 77
5.3.1.4.1 Method of Test . 77
5.3.1.4.2 Test requirements . 78
5.3.1.5 Transmitter maximum output power for UE category 0 . 78
5.3.1.5.1 Method of test . 78
5.3.1.5.2 Test requirements . 78
5.3.1.6 Transmitter maximum output power for UE category M1 . 78
5.3.1.6.1 Method of test . 78
5.3.1.6.2 Test requirements . 79
5.3.2 Transmitter Spectrum Emission Mask . 79
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 79
5.3.2.1.1 Method of test . 79
5.3.2.1.2 Test requirements . 80
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 80
5.3.2.2.1 Method of test . 80
5.3.2.2.2 Test requirements . 81
ETSI
7 ETSI EN 301 908-13 V13.1.1 (2019-11)
5.3.2.2A Transmitter spectrum emission mask for inter-band Carrier Aggregation (DL CA and UL CA) . 81
5.3.2.2A.1 Method of test . 81
5.3.2.2A.2 Test requirements . 82
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 82
5.3.2.3.1 Method of test . 82
5.3.2.3.2 Test requirements . 83
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 83
5.3.2.4.1 Method of test . 83
5.3.2.4.2 Test requirements . 84
5.3.2.5 Transmitter spectrum emission mask for category NB1 . 84
5.3.2.5.1 Method of test . 84
5.3.2.5.2 Test requirements . 84
5.3.2.6 Transmitter spectrum emission mask for UE category 0 . 85
5.3.2.6.1 Method of test . 85
5.3.2.6.2 Test requirements . 85
5.3.2.7 Transmitter spectrum emission mask for UE category M1 . 85
5.3.2.7.1 Method of test . 85
5.3.2.7.2 Test requirements . 86
5.3.3 Transmitter Spurious Emissions . 86
5.3.3.1 Transmitter spurious emissions for Single Carrier . 86
5.3.3.1.1 Method of test . 86
5.3.3.1.2 Test requirements . 87
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 87
5.3.3.2.1 Method of test . 87
5.3.3.2.2 Test requirements . 88
5.3.3.2A Transmitter spurious emissions for inter-band Carrier Aggregation (DL CA and UL CA) . 88
5.3.3.2A.1 Method of test . 88
5.3.3.2A.2 Test requirements . 89
5.3.3.3 Transmitter spurious emissions for UL-MIMO . 89
5.3.3.3.1 Method of test . 89
5.3.3.3.2 Test requirements . 90
5.3.3.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 90
5.3.3.4.1 Method of test . 90
5.3.3.4.2 Test requirements .
...
SLOVENSKI STANDARD
01-marec-2020
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra -
13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 13:
Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
Ta slovenski standard je istoveten z: ETSI EN 301 908-13 V13.1.1 (2019-11)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
ETSI EN 301 908-13 V13.1.1 (2019-11)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
2 ETSI EN 301 908-13 V13.1.1 (2019-11)
Reference
REN/MSG-TFES-13-13
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 908-13 V13.1.1 (2019-11)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 11
Introduction . 12
1 Scope . 13
2 References . 16
2.1 Normative references . 16
2.2 Informative references . 17
3 Definition of terms, symbols and abbreviations . 17
3.1 Terms . 17
3.2 Symbols . 21
3.3 Abbreviations . 23
4 Technical requirements specifications . 24
4.1 Environmental profile . 24
4.2 Conformance requirements . 24
4.2.0 General . 24
4.2.1 Introduction. 24
4.2.2 Transmitter Maximum Output Power . 25
4.2.2.1 Transmitter maximum output power for Single Carrier . 25
4.2.2.1.1 Definition. 25
4.2.2.1.2 Limits . 26
4.2.2.1.3 Conformance . 26
4.2.2.2 Transmitter output power for Carrier Aggregation (DL CA and UL CA) . 26
4.2.2.2.1 Definition. 26
4.2.2.2.2 Limits . 27
4.2.2.2.3 Conformance . 28
4.2.2.3 Transmitter output power for UL-MIMO . 28
4.2.2.3.1 Definition. 28
4.2.2.3.2 Limits . 28
4.2.2.3.3 Conformance . 28
4.2.2.4 Transmitter output power for category NB1 . 29
4.2.2.4.1 Definition. 29
4.2.2.4.2 Limits . 29
4.2.2.4.3 Conformance . 29
4.2.2.5 Transmitter output power for UE category M1 . 29
4.2.2.5.1 Definition. 29
4.2.2.5.2 Limits . 29
4.2.2.5.3 Conformance . 30
4.2.3 Transmitter Spectrum Emission Mask . 30
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 30
4.2.3.1.1 Definition. 30
4.2.3.1.2 Limits . 30
4.2.3.1.3 Conformance . 31
4.2.3.2 Transmitter spectrum emission mask for Carrier Aggregation (DL CA and UL CA) . 31
4.2.3.2.1 Definition. 31
4.2.3.2.2 Limits . 31
4.2.3.2.3 Conformance . 33
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 33
4.2.3.3.1 Definition. 33
4.2.3.3.2 Limits . 33
4.2.3.3.3 Conformance . 33
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 33
4.2.3.4.1 Definition. 33
4.2.3.4.2 Limits . 33
ETSI
4 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.3.4.3 Conformance . 33
4.2.3.5 Transmitter spectrum emission mask for category NB1 . 33
4.2.3.5.1 Definition. 33
4.2.3.5.2 Limits . 33
4.2.3.5.3 Conformance . 34
4.2.4 Transmitter Spurious Emissions . 34
4.2.4.1 Transmitter spurious emissions for Single Carrier . 34
4.2.4.1.1 Definition. 34
4.2.4.1.2 Limits . 34
4.2.4.1.3 Conformance . 38
4.2.4.2 Transmitter spurious emissions for Carrier Aggregation (DL CA and UL CA) . 38
4.2.4.2.1 Definition. 38
4.2.4.2.2 Limits . 38
4.2.4.2.3 Conformance . 44
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 44
4.2.4.3.1 Definition. 44
4.2.4.3.2 Limits . 44
4.2.4.3.3 Conformance . 44
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 44
4.2.4.4.1 Definition. 44
4.2.4.4.2 Limits . 44
4.2.4.4.3 Conformance . 45
4.2.4.5 Transmitter spurious emissions for category NB1 . 45
4.2.4.5.1 Definition. 45
4.2.4.5.2 Limits . 45
4.2.4.5.3 Conformance . 45
4.2.5 Transmitter Minimum Output Power . 45
4.2.5.1 Transmitter minimum output power for Single Carrier. 45
4.2.5.1.1 Definition. 45
4.2.5.1.2 Limits . 45
4.2.5.1.3 Conformance . 45
4.2.5.2 Transmitter minimum output power for Carrier Aggregation (DL CA and UL CA) . 46
4.2.5.2.1 Definition. 46
4.2.5.2.2 Limits . 46
4.2.5.2.3 Conformance . 46
4.2.5.3 Transmitter minimum output power for UL-MIMO . 46
4.2.5.3.1 Definition. 46
4.2.5.3.2 Limits . 46
4.2.5.3.3 Conformance . 47
4.2.5.4 Transmitter minimum output power for category NB1 . 47
4.2.5.4.1 Definition. 47
4.2.5.4.2 Limits . 47
4.2.5.4.3 Conformance . 47
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 47
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 47
4.2.6.1.1 Definition. 47
4.2.6.1.2 Limits . 47
4.2.6.1.3 Conformance . 48
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 48
4.2.6.2.1 Definition. 48
4.2.6.2.2 Limits . 49
4.2.6.2.3 Conformance . 49
4.2.6.3 Receiver Adjacent Channel Selectivity (ACS) for category NB1 . 50
4.2.6.3.1 Definition. 50
4.2.6.3.2 Limits . 50
4.2.6.3.3 Conformance . 50
4.2.7 Receiver Blocking Characteristics . 50
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 50
4.2.7.1.1 Definition. 50
4.2.7.1.2 Limits . 50
4.2.7.1.3 Conformance . 52
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 52
ETSI
5 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.7.2.1 Definition. 52
4.2.7.2.2 Limits . 53
4.2.7.2.3 Conformance . 55
4.2.7.3 Receiver Blocking Characteristics for category NB1 . 56
4.2.7.3.1 Definition. 56
4.2.7.3.2 Limits . 56
4.2.7.3.3 Conformance . 57
4.2.8 Receiver Spurious Response . 57
4.2.8.1 Receiver Spurious Response for Single Carrier . 57
4.2.8.1.1 Definition. 57
4.2.8.1.2 Limits . 57
4.2.8.1.3 Conformance . 58
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 58
4.2.8.2.1 Definition. 58
4.2.8.2.2 Limits . 58
4.2.8.2.3 Conformance . 58
4.2.8.3 Receiver Spurious Response for category NB1 . 58
4.2.8.3.1 Definition. 58
4.2.8.3.2 Limits . 58
4.2.8.3.3 Conformance . 59
4.2.9 Receiver Intermodulation Characteristic . 59
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 59
4.2.9.1.1 Definition. 59
4.2.9.1.2 Limits . 59
4.2.9.1.3 Conformance . 59
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 60
4.2.9.2.1 Definition. 60
4.2.9.2.2 Limits . 60
4.2.9.2.3 Conformance . 60
4.2.9.3 Receiver Intermodulation Characteristics for category NB1 . 60
4.2.9.3.1 Definition. 60
4.2.9.3.2 Limits . 61
4.2.9.3.3 Conformance . 61
4.2.10 Receiver Spurious Emissions . 61
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 61
4.2.10.1.1 Definition. 61
4.2.10.1.2 Limits . 61
4.2.10.1.3 Conformance . 61
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 61
4.2.10.2.1 Definition. 61
4.2.10.2.2 Limits . 62
4.2.10.2.3 Conformance . 62
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 62
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 62
4.2.11.1.1 Definition. 62
4.2.11.1.2 Limits . 62
4.2.11.1.3 Conformance . 63
4.2.11.2 Transmitter adjacent channel leakage power ratio for Carrier Aggregation (DL CA and UL CA). 63
4.2.11.2.1 Definition. 63
4.2.11.2.2 Limits for CA UTRA . 64
4.2.11.2.3 Limits for CA EUTRA . 65
4.2.11.2.4 Conformance . 65
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 65
4.2.11.3.1 Definition. 65
4.2.11.3.2 Limits . 66
4.2.11.3.3 Conformance . 67
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 67
4.2.11.4.1 Definition. 67
4.2.11.4.2 Limits . 67
4.2.11.4.3 Conformance . 67
4.2.11.5 Transmitter adjacent channel leakage power ratio for category NB1 . 67
ETSI
6 ETSI EN 301 908-13 V13.1.1 (2019-11)
4.2.11.5.1 Definition. 67
4.2.11.5.2 Limits . 67
4.2.11.5.3 Conformance . 68
4.2.12 Receiver Reference Sensitivity Level . 68
4.2.12.0 General . 68
4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 68
4.2.12.1.1 Definition. 68
4.2.12.1.2 Limits . 68
4.2.12.1.3 Conformance . 68
4.2.12.2 Receiver Reference Sensitivity Level for Carrier Aggregation in DL-only bands . 69
4.2.12.2.1 Definition. 69
4.2.12.2.2 Limits . 69
4.2.12.2.3 Conformance . 70
4.2.12.3 Receiver Reference Sensitivity Level for category NB1 . 70
4.2.12.3.1 Definition. 70
4.2.12.3.2 Limits . 70
4.2.12.3.3 Conformance . 70
4.2.12.4 Receiver Reference Sensitivity Level for UE category 0 . 70
4.2.12.4.1 Definition. 70
4.2.12.4.2 Limits . 70
4.2.12.4.3 Conformance . 71
4.2.12.5 Receiver Reference Sensitivity Level for UE category M1 . 71
4.2.12.5.1 Definition. 71
4.2.12.5.2 Limits . 71
4.2.12.5.3 Conformance . 72
5 Testing for compliance with technical requirements . 73
5.1 Environmental conditions for testing . 73
5.2 Interpretation of the measurement results . 73
5.3 Essential radio test suites . 73
5.3.0 General . 73
5.3.1 Transmitter Maximum Output Power . 73
5.3.1.1 Transmitter maximum output power for Single Carrier . 73
5.3.1.1.1 Method of test . 73
5.3.1.1.2 Test requirements . 74
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 74
5.3.1.2.1 Method of test . 74
5.3.1.2.2 Test requirements . 75
5.3.1.2A Transmitter maximum output power for inter-band Carrier Aggregation (DL CA and UL CA) . 75
5.3.1.2A.1 Method of test . 75
5.3.1.2A.2 Test requirements . 76
5.3.1.3 Transmitter maximum output power for UL-MIMO . 76
5.3.1.3.1 Method of test . 76
5.3.1.3.2 Test requirements . 77
5.3.1.4 Transmitter maximum output power for category NB1 . 77
5.3.1.4.1 Method of Test . 77
5.3.1.4.2 Test requirements . 78
5.3.1.5 Transmitter maximum output power for UE category 0 . 78
5.3.1.5.1 Method of test . 78
5.3.1.5.2 Test requirements . 78
5.3.1.6 Transmitter maximum output power for UE category M1 . 78
5.3.1.6.1 Method of test . 78
5.3.1.6.2 Test requirements . 79
5.3.2 Transmitter Spectrum Emission Mask . 79
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 79
5.3.2.1.1 Method of test . 79
5.3.2.1.2 Test requirements . 80
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 80
5.3.2.2.1 Method of test . 80
5.3.2.2.2 Test requirements . 81
ETSI
7 ETSI EN 301 908-13 V13.1.1 (2019-11)
5.3.2.2A Transmitter spectrum emission mask for inter-band Carrier Aggregation (DL CA and UL CA) . 81
5.3.2.2A.1 Method of test . 81
5.3.2.2A.2 Test requirements . 82
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 82
5.3.2.3.1 Method of test . 82
5.3.2.3.2 Test requirements . 83
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 83
5.3.2.4.1 Method of test . 83
5.3.2.4.2 Test requirements . 84
5.3.2.5 Transmitter spectrum emission mask for category NB1 . 84
5.3.2.5.1 Method of test . 84
5.3.2.5.2 Test requirements . 84
5.3.2.6 Transmitter spectrum emission mask for UE category 0 . 85
5.3.2.6.1 Method of test . 85
5.3.2.6.2 Test requirements . 85
5.3.2.7 Transmitter spectrum emission mask for UE category M1 . 85
5.3.2.7.1 Method of test . 85
5.3.2.7.2 Test requirements . 86
5.3.3 Transmitter Spurious Emissions . 86
5.3.3.1 Transmitter spurious emissions for Single Carrier . 86
5.3.3.1.1 Method of test . 86
5.3.3.1.2 Test requirements . 87
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 87
5.3.3.2.1 Method of test . 87
5.3.3.2.2 Test requirements . 88
5.3.3.2A Transmitter spurious emissions for inter-band Carrier Aggregation (DL CA and UL CA) .
...