SIST EN ISO 105-P02:2005

SLOVENSKI STANDARD
01-marec-2005
1DGRPHãþD
SIST EN ISO 105-P02:1999
Tekstilije - Preskušanje barvne obstojnosti - Del P02: Barvna obstojnost pri
plisiranju: parno plisiranje (ISO 105-P02:2002)
Textiles - Tests for colour fastness - Part P02: Colour fastness to pleating: Steam
pleating (ISO 105-P02:2002)
Textilien - Farbechtheitsprüfungen - Teil P02: Farbechtheit gegen Plissieren:
Dampfplissieren (ISO 105-P02:2002)
Textiles - Essais de solidité des teintures - Partie P02: Solidité des teintures au plissage:
Plissage a la vapeur (ISO 105-P02:2002)
Ta slovenski standard je istoveten z: EN ISO 105-P02:2004
ICS:
59.080.01 Tekstilije na splošno Textiles in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 105-P02
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 59.080.01 Supersedes EN ISO 105-P02:1995
English version
Textiles - Tests for colour fastness - Part P02: Colour fastness
to pleating: Steam pleating (ISO 105-P02:2002)
Textiles - Essais de solidité des teintures - Partie P02: Textilien - Farbechtheitsprüfungen - Teil P02: Farbechtheit
Solidité des teintures au plissage: Plissage à la vapeur gegen Plissieren: Dampfplissieren (ISO 105-P02:2002)
(ISO 105-P02:2002)
This European Standard was approved by CEN on 21 December 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 105-P02:2004: E
worldwide for CEN national Members.

Foreword
The text of ISO 105-P02:2002 has been prepared by Technical Committee ISO/TC 38 "Textiles”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
105-P02:2004 by Technical Committee CEN/TC 248 "Textiles and textile products", the
secretariat of which is held by BSI.

This document supersedes EN ISO 105-P02:1995.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2005, and conflicting national
standards shall be withdrawn at the latest by June 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 105-P02:2002 has been approved by CEN as EN ISO 105-P02:2004 without any
modifications.
INTERNATIONAL ISO
STANDARD 105-P02
Third edition
2002-09-15
Textiles — Tests for colour fastness —
Part P02:
Colour fastness to pleating: Steam pleating
Textiles — Essais de solidité des teintures —
Partie P02: Solidité des teintures au plissage: Plissage à la vapeur

Reference number
ISO 105-P02:2002(E)
©
ISO 2002
ISO 105-P02:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved

ISO 105-P02:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 105 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 105-P02 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 1, Tests for coloured
textiles and colorants.
This third edition cancels and replaces the second edition (ISO 105-P02:1993), of which it constitutes a minor
revision.
ISO 105 was previously published in thirteen “parts”, each designated by a letter (e.g. “Part A”), with publication
dates between 1978 and 1985. Each part contained a series of “sections”, each designated by the respective part
letter and by a two-digit serial number (e.g. “Section A01”). These sections are now being republished as separate
documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of
these parts is given in ISO 105-A01.

INTERNATIONAL STANDARD ISO 105-P02:2002(E)

Textiles — Tests for colour fastness —
Part P02:
Colour fastness to pleating: Steam pleating
1 Scope
1.1 This part of ISO 105 specifies a method for determining the resistance of the colour of textiles of all kinds
and in all forms to the action of steam-pleating processes. The materials are not pleated during the test, and it is
emphasized that the test is not intended for assessing the quality of the pleating process.
1.2 Three tests differing in severity are provided; one or more of them may be used depending on the
requirements.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 105. For dated references, subsequent amendments to, or revisi
...