ISO 105-B10:2011
(Main)Textiles — Tests for colour fastness — Part B10: Artificial weathering — Exposure to filtered xenon-arc radiation
Textiles — Tests for colour fastness — Part B10: Artificial weathering — Exposure to filtered xenon-arc radiation
ISO 105-B10:2011 specifies a procedure for exposing textiles to artificial weathering in xenon-arc apparatus, including the action of liquid water and water vapour, in order to determine the weather resistance of the colour of textiles. The exposure is carried out in a test chamber with a filtered xenon-arc light source simulating solar spectral irradiance according to CIE 85:1989, Table 4. The method can be used either for determining the colour fastness or the ageing behaviour of the textile under test. The method is also applicable to white (bleached or optically brightened) textiles.
Textiles — Essais de solidité des coloris — Partie B10: Exposition aux intempéries artificielles — Exposition au rayonnement filtré d'une lampe à arc au xénon
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 105-B10
First edition
2011-10-01
Textiles — Tests for colour fastness —
Part B10:
Artificial weathering — Exposure to
filtered xenon-arc radiation
Textiles — Essais de solidité des coloris —
Partie B10: Exposition aux intempéries artificielles — Exposition au
rayonnement filtré d’une lampe à arc au xénon
Reference number
ISO 105-B10:2011(E)
©
ISO 2011
ISO 105-B10:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 105-B10:2011(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Principle .2
5 Apparatus and reference materials .3
5.1 Laboratory light source .3
5.2 Test chamber .4
5.3 Radiometer .4
5.4 Temperature sensors .4
5.5 Wetting and humidity-control equipment .6
5.6 Specimen holders .6
5.7 Spectrophotometer .6
5.8 Colour-matching lamp .6
5.9 Grey scale for assessing change in colour .7
5.10 Reference materials .7
5.11 Metal or clear plastic sheet (PMA) .7
6 Test specimens .7
6.1 For artificial weathering with water spray .7
6.2 For artificial weathering without water spray .8
7 Exposure conditions .8
7.1 Sets of exposure conditions .8
7.2 Exposure duration .8
7.3 Correlation .8
8 Procedure .9
8.1 Checking of the apparatus .9
8.2 Mounting of the test specimens .9
8.3 Exposure .9
9 Assessment .9
9.1 Colour change .9
9.2 Ageing behaviour .10
10 Test report .10
Annex A (informative) Typical applications and test durations .12
Bibliography .13
© ISO 2011 – All rights reserved iii
ISO 105-B10:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 105-B10 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 1, Tests for
coloured textiles and colorants.
ISO 105 consists of many parts designated by a part letter and a two-digit serial number (e.g. A01), under the
general title Textiles — Tests for colour fastness. A complete list of these parts is given in ISO 105-A01.
iv © ISO 2011 – All rights reserved
ISO 105-B10:2011(E)
Introduction
All four exposure conditions described in this part of ISO 105 are different from the method described in
ISO 105-B04. This part of ISO 105 is not intended to replace ISO 105-B04 but to specify additional test options.
Nevertheless, ISO/TC 38 might consider withdrawing ISO 105-B04 at a later date, after the textile industry has
been able to achieve comprehensive experience using this part of ISO 105.
© ISO 2011 – All rights reserved v
INTERNATIONAL STANDARD ISO 105-B10:2011(E)
Textiles — Tests for colour fastness —
Part B10:
Artificial weathering — Exposure to filtered xenon-arc radiation
1 Scope
This part of ISO 105 specifies a procedure for exposing textiles to artificial weathering in xenon-arc apparatus,
including the action of liquid water and water vapour, in order to determine the weather resistance of the colour
of textiles. The exposure is carried out in a test chamber with a filtered xenon-arc light source simulating
solar spectral irradiance according to CIE 85:1989, Table 4. The method can be used either for determining
the colour fastness or the ageing behaviour of the textile under test. The method is also applicable to white
(bleached or optically brightened) textiles.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 105-A01:2010, Textiles — Tests for colour fastness — Part A01: General principles of testing
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 105-A05, Textiles — Tests for colour fastness — Part A05: Instrumental assessment of change in colour
for determination of grey scale rating
ISO 139, Textiles — Standard atmospheres for conditioning and testing
ISO 4892-1, Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance
ISO 9370, Plastics — Instrumental determination of radiant exposure in weathering tests — General guidance
and basic test method
1)
CIE Publication No. 15, Colorimetry (Third edition)
CIE Publication No. 51.2, A method for assessing the quality of daylight simulators for colorimetry
CIE Publication No. 85:1989, Solar spectral irradiance
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
reference material
material of known performance
3.2
reference specimen
portion of the reference material that is to be exposed
1) Commission Internationale de l’Éclairage, CIE Central Bureau, Kegelgasse 27, A-1030 Vienna, Austria; http://www.cie.
co.at.
© ISO 2011 – All rights reserved 1
ISO 105-B10:2011(E)
3.3
control material
material which is of similar composition and construction to the test material and which is exposed at the same
time for comparison with the test material
3.4
control specimen
portion of the control material that is to be exposed
3.5
radiant exposure
H
amount of the radiant energy, to which a specimen has been exposed, given by the equation
H = ∫ E ⋅ dt
where
E is the irradiance, in watts per square metre;
t is the exposure time, in seconds.
NOTE 1 H is expressed in joules per square metre.
NOTE 2 If the irradiance E is constant throughout the whole exposure time, the radiant exposure H is given simply by
the product of E and t.
3.6
ageing behaviour
change in a property of a textile specimen during artificial weathering
NOTE One measure of ageing is the radiant exposure H in the wavelength range below 400 nm or at a specified
wavelength, e.g. 340 nm. The ageing behaviour of a textile exposed to artificial weathering, or to artificial radiation,
depends on the type of textile, the conditions of exposure of the textile, the property selected for monitoring the progress
of the ageing process and the degree of change in this property.
3.7
ageing criterion
given degree of change in a selected property of the textile under test
NOTE The ageing criterion is specified or agreed upon.
4 Principle
A specimen of the textile to be tested is exposed to artificial radiation from a xenon-arc lamp with or without
periodical wetting. The colour fastness is assessed by comparing the change in colour of the specimen using
the grey scale.
The ageing behaviour is assessed by measuring the degree of change of a selected property, e.g. tensile
strength, compared to an unexposed specimen, using the appropriate test method. The ageing criterion has to
be agreed on by the interested parties and should preferably be one that is important for the practical end-use
of the textile under test.
2 © ISO 2011 – All rights reserved
ISO 105-B10:2011(E)
5 Apparatus and reference materials
5.1 Laboratory light source
5.1.1 General
The light source shall be one or more quartz-jacketed xenon-arc lamps, which emit radiation from about 270 nm
in the ultraviolet through the visible spectrum and into the infrared. In order to simulate global solar radiation at
the earth’s surface as described in CIE 85:1989, Table 4, so-called daylight filters shall be used to remove short
wavelength UV radiation <290 nm. In addition, filters to remove infrared radiation may be used to prevent unrealistic
heating of test specimens that may cause thermal degradation not experienced during outdoor exposures.
NOTE Solar spectral irradiance for a number of different atmospheric conditions is described in CIE 85:1989. In
accordance with other International Standards, this part of ISO 105 uses Table 4 in CIE 85:1989 as a benchmark for solar
spectral irradiance.
The xenon-arc light source may be either air-cooled or water-cooled. Size, form and number of xenon-arc
lamps will depend on the type of apparatus. An irradiance-controlled light source shall be used.
The variation in irradiance over the area covered by the specimens shall not exceed ±10 % of the mean. If this
cannot be achieved, specimens shall be periodically repositioned to provi
...
NORME ISO
INTERNATIONALE 105-B10
Première édition
2011-10-01
Textiles — Essais de solidité des coloris —
Partie B10:
Exposition aux intempéries artificielles —
Exposition au rayonnement filtré d’une
lampe à arc au xénon
Textiles — Tests for colour fastness —
Part B10: Artificial weathering — Exposure to filtered xenon-arc radiation
Numéro de référence
ISO 105-B10:2011(F)
©
ISO 2011
ISO 105-B10:2011(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2011
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord écrit
de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés
ISO 105-B10:2011(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application .1
2 Références normatives .1
3 Termes et définitions .1
4 Principe .2
5 Appareillage et matériaux de référence .3
5.1 Source de lumière de laboratoire .3
5.2 Enceinte d’essai .4
5.3 Radiomètre .4
5.4 Capteurs de température .4
5.5 Matériel de régulation du mouillage et de l’humidité .6
5.6 Supports d’éprouvette .6
5.7 Spectrophotomètre .7
5.8 Source lumineuse pour l’évaluation des couleurs .7
5.9 Échelle de gris pour l’évaluation de la dégradation de la coloration .7
5.10 Matériaux de référence .7
5.11 Feuille de métal ou de plastique transparent (PMA) .7
6 Éprouvettes .7
6.1 Intempéries artificielles par pulvérisation d’eau .7
6.2 Intempéries artificielles sans pulvérisation d’eau .8
7 Conditions d’exposition .8
7.1 Ensembles de conditions d’exposition .8
7.2 Durée d’exposition .9
7.3 Corrélation .9
8 Mode opératoire .9
8.1 Vérification de l’appareillage .9
8.2 Montage des éprouvettes .9
8.3 Exposition .10
9 Évaluation .10
9.1 Dégradation de la coloration .10
9.2 Comportement au vieillissement .10
10 Rapport d’essai .11
Annexe A (informative) Applications et durées d’essai types .12
Bibliographie .13
© ISO 2011 – Tous droits réservés iii
ISO 105-B10:2011(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux de
normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général confiée aux
comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales,
en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur publication
comme Normes internationales requiert l’approbation de 75 % au moins des comités membres votants.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de droits
de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de ne pas avoir
identifié de tels droits de propriété et averti de leur existence.
L’ISO 105-B10 a été élaborée par le comité technique ISO/TC 38, Textiles, sous-comité SC 1, Essais des
textiles colorés et des colorants.
L’ISO 105 se compose de nombreuses parties désignées par une lettre et deux chiffres (par exemple A01),
sous le titre général Textiles — Essais de solidité des coloris. Une liste complète de ces parties est donnée
dans l’ISO 105-A01.
iv © ISO 2011 – Tous droits réservés
ISO 105-B10:2011(F)
Introduction
Les quatre conditions d’exposition décrites dans la présente partie de l’ISO 105 diffèrent de la méthode décrite
dans l’ISO 105-B04. La présente partie de l’ISO 105 n’est pas destinée à remplacer l’ISO 105-B04 mais à
spécifier des options d’essai supplémentaires. Toutefois, le Comité technique ISO/TC 38 est susceptible de
retirer ultérieurement l’ISO 105-B04, lorsque l’industrie textile aura acquis une expérience suffisante de la
présente partie de l’ISO 105.
© ISO 2011 – Tous droits réservés v
NORME INTERNATIONALE ISO 105-B10:2011(F)
Textiles — Essais de solidité des coloris —
Partie B10:
Exposition aux intempéries artificielles — Exposition au
rayonnement filtré d’une lampe à arc au xénon
1 Domaine d’application
La présente partie de l’ISO 105 spécifie un mode opératoire d’exposition des textiles aux intempéries artificielles
à l’aide d’un appareillage à arc au xénon avec action de l’eau et de la vapeur d’eau dans le but de déterminer la
résistance des coloris des textiles aux intempéries. L’exposition a lieu dans une enceinte d’essai munie d’une
source de lumière filtrée à arc au xénon qui simule l’éclairement énergétique spectral solaire, conformément
à la publication CIE 85:1989, Tableau 4. La méthode permet de déterminer soit la solidité des coloris, soit le
comportement au vieillissement du textile soumis à l’essai. La méthode est applicable également aux textiles
blancs (blanchis ou traités aux azurants optiques).
2 Références normatives
Les documents de référence suivants sont indispensables pour l’application du présent document. Pour les
références datées, seule l’édition citée s’applique. Pour les références non datées, la dernière édition du
document de référence s’applique (y compris les éventuels amendements).
ISO 105-A01:2010, Textiles — Essais de solidité des coloris — Partie A01: Principes généraux pour
effectuer les essais
ISO 105-A02, Textiles — Essais de solidité des teintures — Partie A02: Échelle de gris pour l’évaluation
des dégradations
ISO 105-A05, Textiles — Essais de solidité des teintures — Partie A05: Évaluation instrumentale du changement
de couleur pour conversion en degrés de l’échelle de gris
ISO 139, Textiles — Atmosphères normales de conditionnement et d’essai
ISO 4892-1, Plastiques — Méthodes d’exposition à des sources lumineuses de laboratoire — Partie 1: Guide général
ISO 9370, Plastiques — Détermination au moyen d’instruments de l’exposition énergétique lors d’essais
d’exposition aux intempéries — Lignes directrices générales et méthode d’essai fondamentale
Publication CIE N° 15, Colorimétrie (Troisième édition)
Publication CIE N° 51.2, Une méthode d’évaluation de la qualité des simulateurs de lumière du jour pour la colorimétrie
1))
Publication CIE N° 85:1989, Distribution spectrale de l’éclairement solaire
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s’appliquent.
3.1
matériau de référence
matériau de performances connues
)
1) Commission Internationale de l’Éclairage, CIE Central Bureau, Kegelgasse 27, A-1030 Vienne, Autriche; http://
www.cie.co.at.
© ISO 2011 – Tous droits réservés 1
ISO 105-B10:2011(F)
3.2
éprouvette de référence
portion du matériau de référence à exposer
3.3
matériau témoin
matériau de composition et de construction semblables à celles du matériau d’essai, exposé au même moment
pour être comparé au matériau d’essai
3.4
éprouvette témoin
portion du matériau témoin à exposer
3.5
exposition énergétique
H
quantité d’énergie rayonnante à laquelle une éprouvette a été exposée, donnée par l’équation
H =⋅Etd
∫
où
E est l’éclairement énergétique, en watts par mètre carré;
t est la durée d’exposition, en secondes
NOTE 1 H est exprimée en joules par mètre carré.
NOTE 2 Si l’éclairement énergétique, E, est constant pendant toute la durée de l’exposition, l’exposition énergétique,
H, est simplement donnée par le produit de E et t.
3.6
comportement au vieillissement
modification d’une propriété d’une éprouvette de textile au cours de l’exposition aux intempéries artificielles
NOTE L’exposition énergétique, H, dans la gamme de longueurs d’ondes inférieures à 400 nm ou à une longueur
d’onde spécifiée, par exemple 340 nm, constitue une mesure du vieillissement. Le comportement au vieillissement des
textiles exposés aux intempéries artificielles, ou à un rayonnement artificiel, dépend du type de textile, des conditions
d’exposition, de la propriété retenue pour suivre l’évolution du processus de vieillissement et du degré de modification de
cette propriété.
3.7
critère de vieillissement
degré donné de modification d’une propriété choisie pour le textile soumis à l’essai
NOTE Le critère de vieillissement est spécifié ou convenu.
4 Principe
Une éprouvette du textile à soumettre à l’essai est exposée à un rayonnement artificiel au moyen d’une lampe
à arc au xénon, avec ou sans mouillage périodique. La solidité des coloris est évaluée par comparaison de la
dégradation de la coloration de l’éprouvette à l’aide de l’échelle de gris.
Le comportement au vieillissement est évalué en mesurant le degré de modification d’une propriété donnée, par
exemple la résistance à la traction, et en le comparant à celui d’une éprouvette non exposée, suivant une méthode
d’essai adaptée. Le critère de vieillissement doit être décidé d’un commun accord entre les parties intéressées et
il convient de retenir un critère pertinent pour l’application à laquelle le textile soumis à l’essai est destiné.
2 © ISO 2011 – Tous droits réservés
ISO 105-B10:2011(F)
5 Appareillage et matériaux de référence
5.1 Source de lumière de laboratoire
5.1.1 Généralités
La source de lumière doit être constituée d’une ou plusieurs lampes à arc au xénon en quartz qui émettent
un rayonnement à partir d’environ 270 nm dans l’ultraviolet jusqu’à l’infrarouge en passant par le spectre
visible. Afin de simuler le rayonnement solaire global à la surface de la Terre, comme décrit dans la publication
CIE 85:1989,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.