ISO 9528:2022

INTERNATIONAL ISO
STANDARD 9528
Third edition
2022-01
Aerospace — Standard-weight
polytetrafluoroethylene (PTFE) hose
assemblies, classification 204 °C/
21 000 kPa — Procurement
specification
Aéronautique et espace — Tuyauteries flexibles en
polytétrafluoroéthylène (PTFE), série normale, classification
204 °C/21 000 kPa — Spécification d'approvisionnement
Reference number
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
4.1 General . 1
4.2 Qualification . 2
4.3 Materials . 2
4.3.1 General . 2
4.3.2 Metals . 2
4.4 Construction . 2
4.4.1 General . 2
4.4.2 Inner tube . 3
4.4.3 Reinforcement . 3
4.4.4 Fittings . 3
4.5 Inner tube . 3
4.5.1 Density and relative density . 3
4.5.2 Tensile strength . 3
4.5.3 Elongation . 3
4.5.4 Tube roll . 4
4.5.5 Tube proof-pressure . 4
4.5.6 Electrical conductivity . 4
4.6 Hose . 4
4.6.1 Dimensional requirements. 4
4.6.2 Physical requirements. 4
4.6.3 Bore check . 4
4.7 Screw threads . . 4
4.8 Part numbering of interchangeable parts . 4
4.9 Identification of products . 4
4.9.1 General . 4
4.9.2 Fittings . 6
4.9.3 Hose assembly . 6
4.10 Workmanship . 6
4.10.1 General . 6
4.10.2 Dimensions and tolerances . 6
4.10.3 Cleaning . 6
4.11 Hose assembly — Test and performance requirements . 6
4.11.1 Proof pressure . 6
4.11.2 Elongation and contraction . 6
4.11.3 Volumetric expansion . 6
4.11.4 Leakage . 7
4.11.5 Thermal shock . 7
4.11.6 Impulse. 7
4.11.7 Assembly flexibility . 7
4.11.8 Stress degradation . 7
4.11.9 Pneumatic surge . 7
4.11.10 Pneumatic effusion . 8
4.11.11 Repeated installation . 9
4.11.12 Burst pressure at room temperature . 9
4.11.13 Electrical conductivity . 9
4.11.14 Fire resistance . 9
5 Quality assurance . 9
5.1 Responsibility for inspection. 9
iii
5.2 Classification of inspections . 10
5.3 Qualification inspections . 10
5.3.1 Qualification test samples . 10
5.3.2 Test report, test samples and data for the purchaser. 10
5.3.3 Qualification testing .12
5.3.4 Criteria for requalification .12
5.4 Quality conformance inspections .12
5.4.1 General .12
5.4.2 Individual tests .12
5.4.3 Sampling tests .12
5.4.4 Periodic control tests .13
5.4.5 Rejection and re-test . .13
5.4.6 Changes in inspection procedures . 13
5.4.7 Destructive test sample .13
5.5 Test conditions . 14
5.5.1 Assembly, ends and hose . 14
5.5.2 End connections . 14
5.5.3 Test fluids . . 14
5.5.4 Temperature measurements .
...