EN 13445-5:2009/A2:2011

SLOVENSKI STANDARD
01-november-2011
1HRJUHYDQHWODþQHSRVRGHGHO3UHJOHGLQSUHVNXãDQMH'RSROQLOR$
Unfired pressure vessels - Part 5 : Inspection and testing
Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
Récipients sous pression non soumis à la flamme - Partie 5: Inspection et contrôle
Ta slovenski standard je istoveten z: EN 13445-5:2009/A2:2011
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13445-5:2009/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 23.020.30
English Version
Unfired pressure vessels - Part 5: Inspection and testing
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
5: Inspection et contrôles
This amendment A2 modifies the European Standard EN 13445-5:2009; it was approved by CEN on 8 July 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-5:2009/A2:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to Annex A .4

Foreword
This document (EN 13445-5:2009/A2:2011) has been prepared by Technical Committee CEN/TC 54 “Unfired
pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-5:2009 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting
national standards shall be withdrawn at the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This document includes the text of the amendment itself. The corrected pages of EN 13445-5 will be delivered
as issue 3 of the standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
1 Modification to Annex A
Delete the existing Annex A and substitute the following.
Annex A
(normative)
Inspection and testing of serially produced pressure vessels
A.1 Introduction
Inspection and testing of serially produced vessels manufactured according to this standard may have
reduction according to this Annex A. The vessel shall be within the limitations of this Annex to be classified as
serially produced and have model acceptance as defined in 3.10 according to this Annex.
This Annex describes the level of inspection and testing of serially produced pressure vessels in accordance
with this standard to permit reduced levels of NDT during serial production. The inspection and testing plan
has to be described in the documents that are part of model acceptance.
NOTE See Clause 3 of this Part 5 for terms and definitions which are specifically relevant to serially produced
pressure vessels of this annex.
A.2 Limitations for vessels permitted to
...