EN 16307-3:2023

SLOVENSKI STANDARD
01-junij-2023
Vozila za talni transport - Varnostne zahteve in preverjanje - 3. del: Dodatne
zahteve za tovornjake z dvignjenim položajem upravljavca in tovornjake, posebej
zasnovane za vožnjo z dvignjenim bremenom (dodatne zahteve k EN 16307-1)
Industrial trucks - Safety requirements and verification - Part 3 Supplementary
requirements for trucks with elevating operator position and trucks specifically designed
to travel with elevated loads (additional requirements to EN 16307-1)
Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 3:
Zusätzliche Anforderungen für Flurförderzeuge mit hebbarem Fahrerplatz und
Flurförderzeuge, die zum Fahren mit angehobener Last ausgelegt sind (zusätzliche
Anforderungen zu EN 16307-1)
Chariots de manutention - Exigences de sécurité et vérification - Partie 3: Exigences
supplémentaires pour chariots avec poste de conduite élevable et pour chariots
spécialement conçus pour une conduite avec des charges en élévation (exigences
complémentaires à l'EN 16307 1)
Ta slovenski standard je istoveten z: EN 16307-3:2023
ICS:
53.060 Industrijski tovornjaki Industrial trucks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16307-3
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2023
EUROPÄISCHE NORM
ICS 53.060
English Version
Industrial trucks - Safety requirements and verification -
Part 3: Supplementary requirements for trucks with
elevating operator position and trucks specifically
designed to travel with elevated loads (additional
requirements to EN 16307-1)
Chariots de manutention - Exigences de sécurité et Flurförderzeuge - Sicherheitstechnische
vérification - Partie 3 : Exigences supplémentaires pour Anforderungen und Verifizierung - Teil 3: Zusätzliche
chariots avec poste de conduite élevable et pour Anforderungen für Flurförderzeuge mit hebbarem
chariots spécialement conçus pour une conduite avec Fahrerplatz und Flurförderzeuge, die zum Fahren mit
des charges en élévation (exigences complémentaires à angehobener Last ausgelegt sind (zusätzliche
l'EN 16307-1) Anforderungen zu EN 16307-1)
This European Standard was approved by CEN on 9 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16307-3:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Safety requirements and/or protective measures . 6
4.1 General. 6
4.2 Brakes – Operation without guidance systems . 6
4.3 Operator fall protection . 6
5 Verification of the safety requirements and/or protective/risk reduction measures 6
6 Information for use . 7
6.1 Instruction handbooks. 7
6.2 Marking . 7
6.2.1 Fall protection devices . 7
6.2.2 Fall hazard . 7
Annex A (informative) List of significant hazards . 8
Bibliography . 9

European foreword
This document (EN 16307-3:2023) has been prepared by Technical Committee CEN/TC 150 “Industrial
trucks - Safety”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2023, and conflicting national standards shall
be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
The EN 16307 series, under the general title Industrial trucks — Safety requirements and verification,
consists of the following parts:
— Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks,
variable-reach trucks and burden-carrier trucks;
— Part 2: Supplementary requirements for self-propelled variable-reach trucks;
— Part 3: Supplementary requirements for trucks with elevating operator position and trucks specifically
designed to travel with elevated loads (additional requirements to EN 16307-1);
— Part 5: Supplementary requirements for pedestrian-propelled trucks;
— Part 6: Supplementary requirements for burden and personnel carriers.
This document is intended to be used with:
— EN ISO 3691-1:2015 , Industrial trucks — Safety requirements and verification — Part 1: Self-
propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier
trucks (ISO 3691-1:2011); and
— EN ISO 3691-3:2016 , Industrial trucks — Safety requirements and verification — Part 3: Additional
requirements for trucks with elevating operator position and trucks specifically designed to travel with
elevated loads (ISO 3691-3:2016); and
— EN 16307-1:2020, Industrial trucks — Safety requirements and verification — Part 1: Supplementary
requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and
burden-carrier trucks.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
This document is a type-C standard as stated in EN ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to mac
...