EN 13100-2:2004

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neporušitveno preskušanje zvarjenih spojev plastomernih polizdelkov - 2. del: Rentgensko (radiografsko) preskušanjeZerstörungsfreie Prüfung von Schweißverbindungen thermoplastischer Kunststoffe - Teil 2: RöntgenprüfungEssais non destructifs des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 2: Contrôle radiographique par rayons XNon-destructive testing of welded joints in thermoplastics semi-finished products - Part 2: X-ray radiographic testing83.140.01Izdelki iz gume in polimernih materialov na splošnoRubber and plastics products in general25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN 13100-2:2004SIST EN 13100-2:2005en01-marec-2005SIST EN 13100-2:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13100-2November 2004ICS 25.160.40English versionNon-destructive testing of welded joints in thermoplastics semi-finished products - Part 2: X-ray radiographic testingEssais non destructifs des assemblages soudés surproduits semi-finis en thermoplastiques - Partie 2: Contrôleradiographique par rayons XZerstörungsfreie Prüfung von Schweißverbindungenthermoplastischer Kunststoffe - Teil 2: RöntgenprüfungThis European Standard was approved by CEN on 14 October 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13100-2:2004: ESIST EN 13100-2:2005

Minimum image quality values.14 A.1 Single-wall technique; IQI on source side.14 A.2 Double-wall technique; double image; IQI on source side.15 A.3 Double-wall thickness; single or double image; IQI on film side.15 Annex B (informative)
Recommended number of exposures when using the perpendicular, double-wall, single-image and single-wall off-centre techniques for a circumferential butt weld.16
mm t Nominal thickness mm w Penetrated thickness mm
S Radiation source — F Film — α Inclination angle
SDR Dn/t — 5 General 5.1 Security Measures Local or national or international safety precautions when using ionising radiation shall be strictly applied. WARNING NOTICE - Exposure of any part of the human body to X-rays can be highly injurious to health. Wherever X-ray equipment is in use, appropriate legal requirements shall be applied.
5.2 Surface preparation and stage of manufacture Prior to radiography the joint shall be cleaned to remove all traces of dirt etc. from the component surface, which might later cause difficulty in detecting defects. In the case of heated tool butt welded pipes, the external weld bead shall be removed prior to radiography. SIST EN 13100-2:2005
...