EN 1982:2017

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Bloki za pretaljevanje in ulitkiKupfer und Kupferlegierungen - Blockmetalle und GussstückeCuivre et alliages de cuivre - Lingots et pièces mouléesCopper and copper alloys - Ingots and castings77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 1982:2017SIST EN 1982:2017en01-november-2017SIST EN 1982:2017SLOVENSKI
STANDARDSIST EN 1982:20081DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1982
September
t r s y ICS
y yä s w rä u r Supersedes EN
s { z tã t r r zEnglish Version
Copper and copper alloys æ Ingots and castings Cuivre et alliages de cuivre æ Lingots et pièces moulées Kupfer und Kupferlegierungen æ Blockmetalle und Gussstücke This European Standard was approved by CEN on
{ July
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s { z tã t r s y ESIST EN 1982:2017

Guidance for the ordering and supply of copper and copper alloy castings . 21 Annex B (informative)
Optional supplementary testing procedures for ingots and castings . 23 Annex C (normative)
Unalloyed copper . 26 Annex D (normative)
Copper-chromium alloys . 27 Annex E (normative)
Copper-zinc alloys . 28 Annex F (normative)
Copper-zinc-aluminium alloys . 29 Annex G (normative)
Copper-zinc-lead alloys . 33 Annex H (normative)
Copper-zinc-silicon alloys . 42 Annex I (normative)
Other copper-zinc alloys . 44 Annex J (normative)
Copper-tin alloys . 48 Annex K (normative)
Copper-tin-zinc-lead alloys . 53 Annex L (normative)
Copper-tin-lead alloys . 59 Annex M (normative)
Copper-aluminium alloys . 63 Annex N (normative)
Copper-manganese alloys . 68 Annex O (normative)
Copper-nickel alloys . 69 Annex P (normative)
Copper-silicon-zinc alloys . 73 Annex ZA (informative)
Relationship between this European Standard and the Essential Safety Requirements of Directive 2014/68/EU aimed to be covered . 75 Bibliography . 76
Casting EN 1982 — CuAl10Fe5Ni5-C — GS — XXXX
or
Casting EN 1982 — CC333G — GS — XXXX Denomination
Number of this European Standard
Material designation
Casting process
Pattern number
Ingots conforming to this standard, in material designated either CuAl10Fe5Ni5-B or CB333G, shall be designated as follows: Ingot EN 1982 — CuAl10Fe5Ni5-B or Ingot EN 1982 — CB333G 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on the enquiry and order the following information: a) quantity of product required (mass or number of castings); b) denomination (ingot or casting); c) number of this European Standard (EN 1982); d) material designation (see Annex C to Annex P); e) for castings, the casting process to be used (see 4.2 and Annex C to Annex P); f) for castings, full details of the casting(s), i.e. a fully dimensioned drawing, or identification of the casting by, for instance, reference to a pattern, die or drawing number (see Annex A); g) for copper castings and for copper-chromium castings (see Table C.1 and Table D.1), whether the electrical conductivity is to be determined, and if so the test details and sampling rate (see 8.3) and for copper sand castings, whether Grade A, B or C electrical conductivity is required (see Table C.1); SIST EN 1982:2017
...