EN ISO 8130-11:2010
(Main)Coating powders - Part 11: Inclined-plane flow test (ISO 8130-11:1997)
General Information
- Abstract
Specifies a method for determining the flow characteristics of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal. the result of the test described gives an indication of the degree of melt flow that may occur during the curing of the coating powder. This characteristic contributes to the coherence of the coating, to its surface appearance and to the degree of coverage over sharp edges. The test acts as a useful method for checking for batch to batch variation in the behaviour of a given coating powder. Correlation between the results from coating powders of differing composition is not to be expected. This method is unlikely to yield meaningful results with coating powders which have gel times of less than one minute at the test temperature when characterised according to ISO 8130-6.
- Status
- Withdrawn
- Publication Date
- 09-Nov-2010
- Withdrawal Date
- 22-Sep-2026
- Technical Committee
- CEN/TC 139 - Paints and varnishes
- Drafting Committee
- CEN/TC 139 - Paints and varnishes
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 08-May-2019
- Completion Date
- 23-Sep-2026
Relations
- Replaced By
EN ISO 8130-11:2019 - Coating powders - Part 11: Inclined-plane flow test (ISO 8130-11:2019) - Effective Date
- 15-May-2019
- Effective Date
- 25-Aug-2026
- Effective Date
- 25-Aug-2026
- Effective Date
- 25-Aug-2026
- Effective Date
- 25-Aug-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN ISO 8130-11:2010 is a standard published by the European Committee for Standardization (CEN). Its full title is "Coating powders - Part 11: Inclined-plane flow test (ISO 8130-11:1997)". This standard covers: Specifies a method for determining the flow characteristics of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal. the result of the test described gives an indication of the degree of melt flow that may occur during the curing of the coating powder. This characteristic contributes to the coherence of the coating, to its surface appearance and to the degree of coverage over sharp edges. The test acts as a useful method for checking for batch to batch variation in the behaviour of a given coating powder. Correlation between the results from coating powders of differing composition is not to be expected. This method is unlikely to yield meaningful results with coating powders which have gel times of less than one minute at the test temperature when characterised according to ISO 8130-6.
Specifies a method for determining the flow characteristics of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal. the result of the test described gives an indication of the degree of melt flow that may occur during the curing of the coating powder. This characteristic contributes to the coherence of the coating, to its surface appearance and to the degree of coverage over sharp edges. The test acts as a useful method for checking for batch to batch variation in the behaviour of a given coating powder. Correlation between the results from coating powders of differing composition is not to be expected. This method is unlikely to yield meaningful results with coating powders which have gel times of less than one minute at the test temperature when characterised according to ISO 8130-6.
EN ISO 8130-11:2010 is classified under the following ICS (International Classification for Standards) categories: 87.040 - Paints and varnishes. The ICS classification helps identify the subject area and facilitates finding related standards.
EN ISO 8130-11:2010 has the following relationships with other standards: It is inter standard links to EN ISO 8130-11:2019, ISO 8130-9:1992, ISO 8130-2:1992, ISO 8130-3:1992, ISO 8130-6:1992, EN ISO 9787:1999, EN ISO 11593:1997, EN ISO 8373:1996. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN ISO 8130-11:2010 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
3UDãNDVWLSUHPD]LGHO 3UHVNXVWHþHQMDQDQDJQMHQLSRYUãLQL ,62
Coating powders - Part 11: Inclined-plane flow test (ISO 8130-11:1997)
Pulverlacke - Teil 10: Prüfung des Fließverhaltens auf einer geneigten Platte (ISO 8130-
10:1997)
Poudres pour revêtement - Partie 11: Essai d'écoulement sur plan incliné (ISO 8130-
11:1997)
Ta slovenski standard je istoveten z: EN ISO 8130-11:2010
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 8130-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 87.040
English Version
Coating powders - Part 11: Inclined-plane flow test (ISO 8130-
11:1997)
Poudres pour revêtement - Partie 11: Essai d'écoulement Pulverlacke - Teil 11: Prüfung des Fließverhaltens auf einer
sur plan incliné (ISO 8130-11:1997) geneigten Platte (ISO 8130-11:1997)
This European Standard was approved by CEN on 16 October 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-11:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 8130-11:1997 has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO 8130-11:2010
by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the
latest by May 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8130-11:1997 has been approved by CEN as a EN ISO 8130-11:2010 without any
modification.
IS0
INTERNATIONAL
8130-l 1
STANDARD
First edition
1997-06-o 1
Coating powders -
Part 11:
Inclined-plane flow test
Poudres pour revgtement -
Partie I 1: Essai d’kcoulement sur p/an inch6
Reference number
IS0 8130-11:1997(E)
Iso 8130=11:1997(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on
that committee. International organizations, governmental and non-
in liaison with ISO, also take part in the work. IS0
governmental,
collaborates closelv with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a
vote.
International Standard IS0 813041 was prepared by Technical Committee
ISO/TC 35, Paints and varnishes, Subcommittee SC 9, General test methods
forpaints and varnishes.
IS0 8130 consists of the following parts, under the general title Coating
powders:
Part 1: Determination ofparticle size distribution by sieving
Part 2: Determination of density by gas comparison pyknometer (referee
method)
Part 3: Determination of density by liquid displacementpyknometer
0 ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without permission in writing from the
publisher.
International Organization for Standardization
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Internet central@iso.ch
x.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
0 IS0 IS0 8130-11:1997(E)
Part 4: Calculation of lower explosion limit
Part 5: Determination offlow propetiies of a powder/air mixture
Part 6 Determination of gel time of tbermosetting coating powders at a
given temperature
Part 7: Determination of loss of mass on stoving
Part 8: Assessment of the stoyage stability of thermosetting powders
Pati 9: Sampling
Part 10: Determination of deposition efficiency
Part 11: Inclined-plane flow test
Part 12: Determination of compatibility
This page intentionally left blank
IS0 8130~11:1997(E)
INTERNATIONAL STANDARD @ IS0
Coating powders -
Part 11:
Inclined-plane flow test
1 Scope
This Part of IS0 8130 is one of a series of sta
...