EN 1175-1:1998

EN 1175-1:1998 is a standard published by the European Committee for Standardization (CEN). Its full title is "Safety of industrial trucks - Electrical requirements - Part 1: General requirements for battery powered trucks". This standard covers: 1.1 This standard specifies electrical and related mechanical safety requirements for design and construction of the electrical installation in battery powered industrial trucks hereinafter referred to as trucks, with nominal voltages of the truck system up to 240 V. The Annex A is normative and gives requirements for "Connectors for traction batteries". Annex B is normative and contains "Electric motors - Output and test rules" and Annex C is normative and contains "Electromagnetic contactors". NOTE 1: Reference is made to this standard in other standards which cover the non-electrical requirements of the various industrial truck types. NOTE 2: This standard does not address the subject of charging of traction batteries (CENELEC TC 21X is preparing safety standards for battery charging). NOTE 3: This standard does not address the subject of electromagnetic compatibility (EMC). NOTE 4: The special requirements for operation in potentially explosive atmospheres are not covered in this standard. 1.2 The requirements of this standard are applicable, when trucks are operated under the following climatic conditions: - Average ambient temperature for continuous duty: +25 øC; - Maximum ambient temperature, short term (up to 1 h): +40 øC; - Lowest ambient temperature for trucks intended for use in normal indoor conditions: +5 øC; - Lowest ambient temperature for trucks intended for use in normal outdoor conditions: -20 øC; - Altitude: up to 2000 m; - Relative humidity: in the range 30 % to 95 % (non condensing). 1.3 This standard covers specific hazards (listed in clause 4), which could occur during the intended use of trucks. For hazards occurring during construction, transportation, commissioning, de-commissioning and disposal, reference should be made to EN 292:1991.

1.1 This standard specifies electrical and related mechanical safety requirements for design and construction of the electrical installation in battery powered industrial trucks hereinafter referred to as trucks, with nominal voltages of the truck system up to 240 V. The Annex A is normative and gives requirements for "Connectors for traction batteries". Annex B is normative and contains "Electric motors - Output and test rules" and Annex C is normative and contains "Electromagnetic contactors". NOTE 1: Reference is made to this standard in other standards which cover the non-electrical requirements of the various industrial truck types. NOTE 2: This standard does not address the subject of charging of traction batteries (CENELEC TC 21X is preparing safety standards for battery charging). NOTE 3: This standard does not address the subject of electromagnetic compatibility (EMC). NOTE 4: The special requirements for operation in potentially explosive atmospheres are not covered in this standard. 1.2 The requirements of this standard are applicable, when trucks are operated under the following climatic conditions: - Average ambient temperature for continuous duty: +25 øC; - Maximum ambient temperature, short term (up to 1 h): +40 øC; - Lowest ambient temperature for trucks intended for use in normal indoor conditions: +5 øC; - Lowest ambient temperature for trucks intended for use in normal outdoor conditions: -20 øC; - Altitude: up to 2000 m; - Relative humidity: in the range 30 % to 95 % (non condensing). 1.3 This standard covers specific hazards (listed in clause 4), which could occur during the intended use of trucks. For hazards occurring during construction, transportation, commissioning, de-commissioning and disposal, reference should be made to EN 292:1991.

EN 1175-1:1998 is classified under the following ICS (International Classification for Standards) categories: 53.060 - Industrial trucks. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 1175-1:1998 has the following relationships with other standards: It is inter standard links to EN 1175-1:1998+A1:2010, EN 15000:2008, EN 12312-1:2001+A1:2009, EN 12312-5:2005+A1:2009, EN 1679-1:1998+A1:2011, EN 1175-3:1998+A1:2010, EN 1459:1998+A3:2012, EN 1175-1:1998/FprA1. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 1175-1:1998 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC, 98/37/EC; Standardization Mandates: M/BC/CEN/91/1. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

EN 1175-1:1998 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.