EN ISO 12215-5:2008/A1:2014

SLOVENSKI STANDARD
01-oktober-2014
0DODSORYLOD.RQVWUXNFLMDWUXSDLQ]DKWHYDQHODVWQRVWLGHO1DþUWRYDQLWODNL]D
WUXSHQDþUWRYDQHQDSHWRVWLLQGRORþDQMHODVWQRVWL'RSROQLOR,62
$PG
Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls,
design stresses, scantlings determination - Amendment 1 (ISO 12215-5:2008/Amd
1:2014)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 5:
Entwurfsdrücke für Einrumpffahrzeuge, Entwurfsspannungen, Ermittlung der
Dimensionierung - Änderung 1 (ISO 12215-5:2008/Amd 1:2014)
Petits navires - Construction de coques et échantillonnage - Partie 5: Pressions de
conception pour monocoques, contraintes de conception, détermination de
l'échantillonnage - Amendement 1 (ISO 12215-5:2008/Amd 1:2014)
Ta slovenski standard je istoveten z: EN ISO 12215-5:2008/A1:2014
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 12215-5:2008/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 47.080
English Version
Small craft - Hull construction and scantlings - Part 5: Design
pressures for monohulls, design stresses, scantlings
determination - Amendment 1 (ISO 12215-5:2008/Amd 1:2014)
Petits navires - Construction de coques et échantillonnage - Kleine Wasserfahrzeuge - Rumpfbauweise und
Partie 5: Pressions de conception pour monocoques, Dimensionierung - Teil 5: Entwurfsdrücke für
contraintes de conception, détermination de Einrumpffahrzeuge, Entwurfsspannungen, Ermittlung der
l'échantillonnage - Amendement 1 (ISO 12215-5:2008/Amd Dimensionierung - Änderung 1 (ISO 12215-5:2008/Amd
1:2014) 1:2014)
This amendment A1 modifies the European Standard EN ISO 12215-5:2008; it was approved by CEN on 28 May 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-5:2008/A1:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4

Foreword
This document (EN ISO 12215-5:2008/A1:2014) has been prepared by Technical Committee ISO/TC 188
“Small craft” in collaboration with CCMC.
This Amendment to the European Standard EN ISO 12215-5:2008 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by January 2015, and
conflicting national standards shall be withdrawn at the latest by January 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12215-5:2018/Amd 1:2014 has been approved by CEN as EN ISO 12215-5:2008/A1:2014
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive 94/25/EC as amended by Directive 2003/44/EC.
Once this International Standard is cited in the Official Journal of the European Union under that Directive and
has been implemented as a national standard in at least one Member State, compliance with the normative
clauses of ISO 12215-5 given in Table ZA.1 confers, within the limits of the scope of ISO 12215-5, a
presumption of conformity with the corresponding Essential Requirements of that Directive and associated
EFTA regulations.
Table ZA.1 — Correspondence between this International Standard and Directive 94/25
...