EN ISO 19932-2:2025

SLOVENSKI STANDARD
01-oktober-2025
Nadomešča:
SIST EN ISO 19932-2:2013
Oprema za zaščito poljščin - Nahrbtni škropilniki - 2. del: Preskusne metode (ISO
19932-2:2025)
Equipment for crop protection - Knapsack sprayers - Part 2: Test methods (ISO 19932-
2:2025)
Pflanzenschutzgeräte - Tragbare Geräte - Teil 2: Prüfverfahren (ISO 19932-2:2025)
Matériel de protection des cultures - Pulvérisateurs à dos - Partie 2: Méthodes d'essai
(ISO 19932-2:2025)
Ta slovenski standard je istoveten z: EN ISO 19932-2:2025
ICS:
65.060.40 Oprema za nego rastlin Plant care equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19932-2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2025
EUROPÄISCHE NORM
ICS 65.060.40 Supersedes EN ISO 19932-2:2013
English Version
Equipment for crop protection - Knapsack sprayers - Part
2: Test methods (ISO 19932-2:2025)
Matériel de protection des cultures - Pulvérisateurs à Pflanzenschutzgeräte - Tragbare Geräte - Teil 2:
dos - Partie 2: Méthodes d'essai (ISO 19932-2:2025) Prüfverfahren (ISO 19932-2:2025)
This European Standard was approved by CEN on 29 June 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19932-2:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC amended by Directive 2009/127/EC
aimed to be covered . 4
European foreword
This document (EN ISO 19932-2:2025) has been prepared by Technical Committee ISO/TC 23 "Tractors
and machinery for agriculture and forestry" in collaboration with Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2026, and conflicting national standards
shall be withdrawn at the latest by February 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19932-2:2013.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 19932-2:2025 has been approved by CEN as EN ISO 19932-2:2025 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC amended by Directive
2009/127/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" and "M/471 Mandate to
CEN for standardisation in the field of machinery for pesticide application" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 2009/127/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC amended by Directive 2009/127/EC
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC amended by
Directive 2009/127/EC
1. ESSENTIAL HEALTH AND
SAFETY REQUIREMENTS
1.1.2. (a) 5
1.1.2. (c) 5
1.1.2. (e) 8
1.1.3. Materials and products 5.3.8
1.1.5. Design of machinery to 5.6
facilitate its handling
1.1.6. Ergonomics 5.6.
1.2. CONTROL SYSTEMS
1.2.1. Safety and reliability of 5.3.1, 5.3.2
control systems
1.2.2. Control devices 5.3.1, 5.4.
1.2.3. Starting 5.3.1.
1.2.4. Stopping 5.3.1.
1.2.4.1. Normal stop 5.3.1.
1.2.4.2. Operational stop 5.3.1.
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC amended by
Directive 2009/127/EC
1.2.4.3. Emergency stop Not covered
1.2.5. Selection of control or  Not covered
operating modes
1.2.6. Failure of the power  Not covered
supply
1.3. PROTECTION AGAINST
MECHANICAL HAZARDS
1.3.1. Risk of loss of stability 5.3.4
1.3.2. Risk of break-up during  Not covered
operation
1.3.3. Risks due to falling or 5.3.3, 8.2.
ejected objects
1.3.4. Risks due to surfaces,  Not covered
edges or angles
1.3.7. Risks related to moving  Not covered
parts
1.5. RISKS DUE TO OTHER
HAZARDS
1.5.13. Emissions of hazardous 5.3.4, 5.4, 5.5, 6.2, 7.1, 8.1.1.
materials and substances
2. SUPPLEMENTARY ESSENTIAL
HEALTH AND SAFETY
REQUIREMENTS FOR CERTAIN
CATEGORIES OF MACHINERY
2.4.2. General 5.3.2, 5.3.4, 5.5, 5.6, 6.2, 6.3, 7.1,
7.2, 8.1.1, 8.1.2, 8.2.
2.4.3. Controls and monitoring 5.3.1, 5.3.5
2.4.4. Filling and emptying 5.3.5, 5.3.6, 5.3.7, 5.4, 6.2, 7.1,
8.1.1.
2.4.5. Applications of pesticides  Not covered
2.4.5.1. Application rate 5.3.1, 5.3.2, 6.1.
2.4.5.2. Distribution, deposition  Not covered
and drift of pesticide
2.4.5.3. Tests 5, 6, 7, 8.
2.4.5.4. Losses during stoppage 5.3.1
2.4.6. Maintenance  Not covered
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC amended by
Directive 2009/127/EC
2.4.6.1. Cleaning 5.3.7.
2.4.6.2. Servicing  Not covered
2.4.7. Inspections  Not covered
2.4.8. Marking of nozzles,  Not covered
strainers and filters
2.4.9. Indication of pesticide in  Not covered
use
2.4.10. Instructions  Not covered
WARNING 1 Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 19932-2
Third edition
Equipment for crop protection —
2025-06
Knapsack sprayers —
Part 2:
Test methods
Matériel de protection des cultures — Pulvérisateurs à dos —
Partie 2: Méthodes d'essai
Reference number
ISO 19932-2:2025(en) © ISO 2025

ISO 19932-2:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 19932-2:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test liquids and equipment . 1
5 General . 2
5.1 Test conditions .2
5.2 Sprayer .2
5.3 Functional tests .3
5.3.1 Spray liquid shut-off device reliability .3
5.3.2 Spray liquid output .3
5.3.3 Load carrying straps and their fixation points .3
5.3.4 Stability .3
5.3.5 Contents gauge scale and total volume .3
5.3.6 Filling rate .4
5.3.7 Emptying .4
5.3.8 Absorbency of harness .5
5.4 Pressure test .
...