CEN/TS 16360:2012

SLOVENSKI STANDARD
01-oktober-2012
%DUYHLQODNL3UHPD]LLQSUHPD]QLVLVWHPL]D]DãþLWROHVDY]XQDQMLXSRUDEL
2FHQMHYDQMHUD]WH]QRVWLILOPD]YWLVNRYDQMHPSUHPD]DQDOHVHQLSRGODJL
Paints and varnishes - Coating materials and coating systems for exterior wood -
Assessment of film extensibility by indentation of a coating on a wooden substrate
Beschichtungsstoffe - Beschichtungsstoffe und Beschichtungssysteme für Holz im
Außenbereich - Beurteilung der Verformbarkeit durch Eindrücken einer Beschichtung auf
einem Holzsubstrat
Peintures et vernis - Produits de peintures et systèmes de peintures pour bois en
extérieur - Évaluation de l'extensibilité du feuil par poinçonnement d'un revêtement sur
un support en bois
Ta slovenski standard je istoveten z: CEN/TS 16360:2012
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN/TS 16360
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
July 2012
ICS 87.040
English Version
Paints and varnishes - Coating materials and coating systems
for exterior wood - Assessment of film extensibility by
indentation of a coating on a wooden substrate
Peintures et vernis - Produits de peintures et systèmes de Beschichtungsstoffe - Beschichtungsstoffe und
peintures pour bois en extérieur - Évaluation de Beschichtungssysteme für Holz im Außenbereich -
l'extensibilité du feuil par poinçonnement d'un revêtement Beurteilung der Verformbarkeit durch Eindrücken einer
sur un support en bois Beschichtung auf einem Holzsubstrat
This Technical Specification (CEN/TS) was approved by CEN on 9 April 2012 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16360:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Principle .5
5 Apparatus .5
6 Procedure .7
6.1 Wood panels .7
6.2 Coating application.7
6.3 Assessment of film extensibility .7
7 Test report .7
Bibliography .9

Foreword
This document (CEN/TS 16360:2012) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
A suitable extensibility of a coating film on wood in exterior use is of importance to follow dimensional changes
of the wood and to resist some mechanical impacts without formation of cracks in the coating film. The simple
method described in this document gives evidence on extensibility of a coating film on wood on an ordinal
sc
...