FprEN ISO 10249

SLOVENSKI STANDARD
01-januar-2026
Tekoča gnojila - Predhodni vizualni pregled in priprava vzorcev za fizikalno
preskušanje (ISO/FDIS 10249:2025)
Fluid fertilizers - Preliminary visual examination and preparation of samples for physical
testing (ISO/FDIS 10249:2025)
Flüssige Düngemittel - Visuelle Vorprüfung und Vorbereitung von Proben für
physikalische Prüfungen (ISO/FDIS 10249:2025)
Engrais liquides - Examen visuel préliminaire et préparation des échantillons pour essais
physiques (ISO/FDIS 10249:2025)
Ta slovenski standard je istoveten z: FprEN ISO 10249
ICS:
65.080 Gnojila Fertilizers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

FINAL DRAFT
International
Standard
ISO/FDIS 10249
ISO/TC 134
Fluid fertilizers — Preliminary
Secretariat: INSO
visual examination and preparation
Voting begins on:
of samples for physical testing
Engrais liquides — Examen visuel préliminaire et préparation des
Voting terminates on:
échantillons pour essais physiques
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 10249:2025(en) © ISO 2025

FINAL DRAFT
ISO/FDIS 10249:2025(en)
International
Standard
ISO/FDIS 10249
ISO/TC 134
Fluid fertilizers — Preliminary
Secretariat: INSO
visual examination and preparation
Voting begins on:
of samples for physical testing
Engrais liquides — Examen visuel préliminaire et préparation des
Voting terminates on:
échantillons pour essais physiques
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 10249:2025(en) © ISO 2025

ii
ISO/FDIS 10249:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Preparation of test sample . 1
4.1 General .1
4.2 Conditioning of container .1
4.3 Opening of container .1
5 Procedure . 2
5.1 Procedures for solutions .2
5.1.1 Visual examination .2
5.1.2 Mixing .2
5.2 Procedures for suspensions . . .2
5.2.1 Visual examination .2
5.2.2 Mixing (where appropriate) .3
5.2.3 Blending and reduction of a series of samples .3
6 Labelling of sample containers . . 4
7 Sample test report . 4
Bibliography . 5

iii
ISO/FDIS 10249:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO’s adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This doc
...