EN ISO 12625-6:2005

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tissue papir in proizvodi iz tissue papirja - 6. del: Ugotavljanje gramature (ISO 12625-6:2005)Tissue-Papier und Tissue-Produkte - Teil 6: Bestimmung der flächenbezogenen Masse (ISO 12625-6:2005)Papier-tissu et produits en tissu - Partie 6: Détermination du grammage (ISO 12625-6:2005)Tissue paper and tissue products - Part 6: Determination of grammage (ISO 12625-6:2005)85.080.20Tissue papirTissue paperICS:Ta slovenski standard je istoveten z:EN ISO 12625-6:2005SIST EN ISO 12625-6:2005en01-maj-2005SIST EN ISO 12625-6:2005SLOVENSKI
STANDARDSIST EN 12625-6:20001DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12625-6
February 2005 ICS 85.060 Supersedes EN 12625-6:1999 English version
Tissue paper and tissue products - Part 6: Determination of grammage (ISO 12625-6:2005)
Papier-tissu et produits en tissu - Partie 6: Détermination du grammage (ISO 12625-6:2005)
Tissue-Papier und Tissue-Produkte - Teil 6: Bestimmung der flächenbezogenen Masse (ISO 12625-6:2005) This European Standard was approved by CEN on 24 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12625-6:2005: ESIST EN ISO 12625-6:2005

Foreword
This document (EN ISO 12625-6:2005) has been prepared by Technical Committee CEN/TC 172 "Pulp, paper and board", the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 6 "Paper, board and pulps".
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn at the latest by August 2005.
This document supersedes EN 12625-6:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Reference numberISO 12625-6:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO12625-6First edition2005-02-01Tissue paper and tissue products — Part 6: Determination of grammage Papier-tissu et produits en tissu — Partie 6: Détermination du grammage
ISO 12625-6:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 12625-6:2005(E) © ISO 2005 – All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Principle.2 5 Apparatus.2 6 Conditioning.2 7 Preparation of test pieces.2 8 Procedure.3 9 Calculation.3 10 Test report.4 11 Precision.4 Bibliography.5
ISO 12625-6:2005(E) iv © ISO 2005 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12625-6 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 172, Pulp, paper and board, in collaboration with Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee SC 2, Test methods and quality specifications for paper and board, in accordance w
...