FprEN ISO 17662
(Main)Welding - Calibration, verification and validation of equipment used for welding, including ancillary activities (ISO/FDIS 17662:2025)
Welding - Calibration, verification and validation of equipment used for welding, including ancillary activities (ISO/FDIS 17662:2025)
This document specifies requirements for calibration, verification and validation of equipment used for:
— control of process variables during fabrication,
— control of the properties of equipment used for welding or welding allied processes,
where the resulting output cannot be readily or economically documented by subsequent monitoring, inspection and testing. This involves process variables influencing the fitness-for-purpose and in particular the safety of the fabricated product.
NOTE This document is based on the lists of process variables stated in International Standards for specification of welding procedures, in particular, but not exclusively in the ISO 15609 series. Future revisions of these International Standards can result in addition or deletion of parameters considered necessary to specify.
Some guidance is, in addition, given in Annex B for requirements for calibration, verification and validation as part of acceptance testing of equipment used for welding or allied processes.
This document does not specify requirements to calibrate, verify and validate as part of inspection, testing, non-destructive testing or measuring of final welded products performed in order to verify product conformance.
This document applies only to calibration, verification and validation of equipment for use in production or on site.
This document does not apply to the manufacture and installation of equipment for welding. Requirements for new equipment are formulated in directives and product codes (standards), as necessary.
Annex C provides information when other parties are involved in calibration, verification and validation activities.
Schweißen - Kalibrierung, Verifizierung und Validierung von Einrichtungen einschließlich ergänzender Tätigkeiten, die beim Schweißen verwendet werden (ISO/FDIS 17662:2025)
Dieses Dokument legt die Anforderungen an die Kalibrierung, Verifizierung und Validierung von Einrichtungen fest, die verwendet werden für:
das Überwachen der Prozessgrößen während der Fertigung,
das Überwachen der Eigenschaften der beim Schweißen oder bei verwandten Prozessen verwendeten Einrichtungen,
die Fälle, wenn die erzielten Ergebnisse durch anschließende Überwachung, Inspektion und Prüfung nicht einfach oder wirtschaftlich dokumentiert werden können. Dies schließt die Einflussgrößen der Prozesse, die auf die Gebrauchseigenschaften und besonders auf die Sicherheit des hergestellten Erzeugnisses einwirken, mit ein.
ANMERKUNG Dieses Dokument beruht auf Aufstellungen von Prozessgrößen, die in den Internationalen Normen für die Schweißanweisungen, im Besonderen, aber nicht ausschließlich, in der Normenreihe ISO 15609, festgelegt sind. Bei späteren Überarbeitungen dieser Internationalen Normen können festzulegende Parameter ergänzt oder gestrichen werden.
Anhang B enthält zusätzlich einige Hinweise für die Anforderungen an die Kalibrierung, Verifizierung und Validierung als Teil der Abnahmeprüfung für die beim Schweißen oder bei verwandten Prozessen verwendeten Einrichtungen.
Dieses Dokument legt keine Anforderungen an die Kalibrierung, Verifizierung und Validierung als Teil der Inspektion, der Prüfung, der zerstörungsfreien Prüfung oder der Messung der geschweißten Endprodukte fest, die durchgeführt werden, um die Übereinstimmung des Produkts zu verifizieren.
Dieses Dokument gilt nur für die Kalibrierung, Verifizierung und Validierung der Einrichtungen, die bei der Produktion oder in der Werkstatt verwendet werden.
Dieses Dokument gilt nicht für die Herstellung und Installation von Schweißeinrichtungen. Die Anforderungen an neue Einrichtungen sind gegebenenfalls in Richtlinien und Produktvorschriften (Normen) festgelegt.
Anhang C informiert darüber, zu welchem Zeitpunkt andere Parteien in die Kalibrierungs-, Verifizierungs- und Validierungstätigkeiten einbezogen sind.
Soudage - Étalonnage, vérification et validation du matériel utilisé pour le soudage, y compris pour les procédés connexes (ISO/FDIS 17662:2025)
Le présent document spécifie les exigences relatives à l’étalonnage, la vérification et la validation du matériel utilisé pour:
— la maîtrise des variables du processus en cours de production;
— la maîtrise des caractéristiques du matériel utilisé pour le soudage ou les activités connexes;
quand l’élément résultant ne peut pas être ultérieurement vérifié dans des conditions simples ou économiques par une surveillance, des contrôles et des essais. Il implique les variables du processus qui influent sur l’aptitude à l’emploi et en particulier sur la sécurité du produit fabriqué.
NOTE Le présent document est basé sur des listes de variables de processus indiquées dans les Normes Internationales de descriptifs de modes opératoires de soudage, en particulier, mais pas exclusivement, dans les séries de normes ISO 15609. De futures révisions de ces Normes internationales pourront avoir pour résultat l’ajout ou la suppression de paramètres ayant été jugés comme devant être spécifiés.
Des conseils sont également donnés en Annexe B pour les exigences relatives à l’étalonnage, la vérification et la validation dans le cadre des essais de réception du matériel utilisé pour le soudage ou les activités connexes.
Le présent document ne spécifie pas les exigences relatives à l’étalonnage, la vérification et la validation dans le cadre du contrôle, d’essais destructifs, d’essais non destructifs ou du mesurage de produits finals soudés, effectués pour vérifier la conformité du produit.
Le présent document s'applique uniquement à l’étalonnage, la vérification, et la validation du matériel pour une utilisation en production ou sur site.
Le présent document ne s'applique pas à la fabrication et à l’installation du matériel de soudage. Les exigences relatives au matériel neuf sont formulées dans les directives et les codes (ou normes) de produits applicables.
L’Annexe C fournit des informations lorsque d'autres parties sont impliquées dans des activités d'étalonnage, de vérification et de validation.
Varjenje - Umerjanje, preverjanje in validacija opreme za varjenje, vključno s pomožnimi dejavnostmi (ISO/FDIS 17662:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 17662:2024
01-september-2024
Varjenje - Umerjanje, preverjanje in validacija opreme za varjenje, vključno s
pomožnimi dejavnostmi (ISO/DIS 17662:2024)
Welding - Calibration, verification and validation of equipment used for welding, including
ancillary activities (ISO/DIS 17662:2024)
Schweißen - Kalibrierung, Verifizierung und Validierung von Einrichtungen einschließlich
ergänzender Tätigkeiten, die beim Schweißen verwendet werden (ISO/DIS 17662:2024)
Soudage - Étalonnage, vérification et validation du matériel utilisé pour le soudage, y
compris pour les procédés connexes (ISO/DIS 17662:2024)
Ta slovenski standard je istoveten z: prEN ISO 17662
ICS:
25.160.30 Varilna oprema Welding equipment
oSIST prEN ISO 17662:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 17662:2024
oSIST prEN ISO 17662:2024
DRAFT
International
Standard
ISO/DIS 17662
ISO/TC 44/SC 10
Welding — Calibration, verification
Secretariat: DIN
and validation of equipment used
Voting begins on:
for welding, including ancillary
2024-07-03
activities
Voting terminates on:
2024-09-25
Soudage — Étalonnage, vérification et validation du matériel
utilisé pour le soudage, y compris pour les procédés connexes
ICS: 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 17662:2024(en)
oSIST prEN ISO 17662:2024
DRAFT
ISO/DIS 17662:2024(en)
International
Standard
ISO/DIS 17662
ISO/TC 44/SC 10
Welding — Calibration, verification
Secretariat: DIN
and validation of equipment used
Voting begins on:
for welding, including ancillary
activities
Voting terminates on:
Soudage — Étalonnage, vérification et validation du matériel
utilisé pour le soudage, y compris pour les procédés connexes
ICS: 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 17662:2024(en)
ii
oSIST prEN ISO 17662:2024
ISO/DIS 17662:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 3
4.1 General .3
4.2 Frequency .4
4.3 Requirements .4
4.4 Process data .5
4.5 Material properties .5
5 Process data common to more than one welding/brazing process . 5
5.1 Process data common to all welding/brazing processes .5
5.2 Requirements specific to several welding/brazing processes .7
5.3 Requirements specific to arc welding (group 1) .8
6 Metal arc welding without gas protection (group 11) . 9
7 Plasma arc welding (group 15) .10
8 Resistance welding (groups 21, 22, 23, 24, and 25) .10
9 Gas welding (group 3) .11
10 Friction welding (group 42) .12
11 Laser beam welding (group 52) .12
12 Electron beam welding (group 51) . 14
13 Stud welding (group 78) .15
14 Brazing and soldering (group 9) . .16
14.1 General .16
14.2 Manual and mechanized flame brazing (group 912) .16
14.3 Induction brazing (group 916) .16
14.4 Resistance brazing (group 918) .17
14.5 Furnace brazing in protective atmosphere (group 921) .17
14.6 Vacuum brazing (group 922) .18
14.7 Furnace brazing in open atmosphere (group 921) .19
14.8 Dip-bath brazing (group 923), salt-bath brazing (group 924) and flux-bath brazing
(group 925) . 20
14.9 Infrared soldering (group 941) . 20
15 Preheat and/or post weld heat treatment .21
15.1 Preheat .21
15.2 Post weld heat treatment .21
16 Post weld cleaning .22
17 Flame cutting (group 81) and other ancillary processes .22
Annex A (informative) Details for stud welding .23
Annex B (informative) Acceptance testing of equipment .25
Annex C (informative) Parties involved .26
Bibliography .27
iii
oSIST prEN ISO 17662:2024
ISO/DIS 17662:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 10, Qual
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.