EN 3375-008:2009

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Elektrische Leitungen für Digitaldatenübertragungen - Teil 008: Einfach geschirmt - Quad 100 Ohm - Typ KD - ProduktnormSérie aérospatiale - Câbles électriques pour transmission de données numériques - Partie 008: Simple tresse - Quarte en étoile 100 Ohms - Type KD - Norme de produitAerospace series - Cable, electrical, for digital data transmission - Part 008: Single braid - Star Quad 100 ohms - Type KD - Product standard49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 3375-008:2009SIST EN 3375-008:2009en01-maj-2009SIST EN 3375-008:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3375-008March 2009ICS 49.060 English VersionAerospace series - Cable, electrical, for digital data transmission- Part 008: Single braid - Star Quad 100 ohms - Type KD -Product standardSérie aérospatiale - Câbles électriques pour transmissionde données numériques - Partie 008: Simple tresse -Quarte en étoile 100 Ohms - Type KD - Norme de produitLuft- und Raumfahrt - Elektrische Leitungen fürDigitaldatenübertragungen - Teil 008: Einfach geschirmt -Quad 100 Ohm - Typ KD - ProduktnormThis European Standard was approved by CEN on 30 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3375-008:2009: ESIST EN 3375-008:2009

EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical cables. 1) EN 9133, Aerospace series — Quality management systems — Qualification procedure for aerospace standard parts. TR 6058, Aerospace series — Cable code identification list. 2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3475-100 apply. 4 Required characteristics 4.1 Configuration, dimensions, tolerances and mass The configuration, dimensions and tolerances shall be in accordance with Figure 1 and Table 1. Mass: ≤ 41 kg/km. Dimensions are in millimetres.
* All parts quoted in Table 3. 1) Published as ASD Prestandard at the date of publication of this standard. 2) Published as ASD Technical Report at the date of publication of this standard. SIST EN 3375-008:2009

NOTE No. of elements in accordance with Table 2. Figure 1 — Configuration, dimensions and tolerances Table 1 — Dimensions, tolerances and general characteristics Stranded conductor (∅ A) 0,598 mm ≤ ∅ ≤ 0,656 mm a
Insulation diameter (single wire) 1,35 mm ≤ ∅ ≤ 1,52 mm a Braid, shield Strand diameter: 0,10 mm Outer diameter of cable (∅ B) < 5,0 mm Colour of the jacket g Light blue Colour of components c Pair 1: Red (+), Blue (−) Pair 2: Yellow (+), Green (−) Minimum bending radius for dynamic installation 10 × Max. outer diameter Minimum bending radius in static 5 × Max. outer diameter a Adapted tools are requested for stripping.
4.2 Material The material and surface treatment shall be
...